ページ1に含まれる内容の要旨
203 Eng Fr Cndn manual 12/21/98 11:19 AM Page 1
®
®
MultiSync
MultiSync
™
™
IntelliBase
IntelliBase
USB Hub
USB Hub
and Audio
and Audio
User’s Manual
User’s Manual
ページ2に含まれる内容の要旨
203 Eng Fr Cndn manual 12/21/98 11:19 AM Page 2 Index Contents 1 Quick Start 2-20 ™ IntelliBase Control Panel 21 Controls 22-23 Specifications 24 Troubleshooting 25 References 26 Limited Warranty 27 Table des matières Contenu 31 Démarrage rapide 32-50 mc Tableau de commande IntelliBase 51 Commandes 52 Caractéristiques 54 Dépannage 55 Références 56 Garantie limitée 57
ページ3に含まれる内容の要旨
203 Eng Fr Cndn manual 12/21/98 11:19 AM Page 3 IMPORTANT The lightning flash with arrowhead, within an CAUTION: TO PREVENT THE RISK OF The exclamation point within an equilateral equilateral triangle, is intended to alert the triangle is intended to alert the user to the ELECTRIC SHOCK, DO NOT REMOVE COVER user to the presence of uninsulated presence of important operating and (OR BACK). NO USER- SERVICEABLE PARTS “dangerous voltage” within the product’s maintenance (servicing) instructio
ページ4に含まれる内容の要旨
203 Eng Fr Cndn manual 12/21/98 11:19 AM Page 4 Connecting the Power Cord AC Wall Socket CAUTION: To prevent electric shock do not use this (polarized) plug with an extension cord, receptacle or other outlet unless the Long slot blades can be fully inserted to prevent blade is neutral exposure. (ground) side. WARNING Insert the wide TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE blade into the TO RAIN OR MOISTURE. ground side slot. The FCC Wants You to Know ® ™ 1.
ページ5に含まれる内容の要旨
® Audio Management Software
Version 1.0 — Important —
To help us in our continuing efforts to better serve and support you, and to bring you new and innovative products, please take a few moments to register your new NEC MultiSync monitor.
By returning this card, we confirm your date of purchase and records the model and serial numbers. This facilitates our ability to process warranty claims, especially if your original proof of purchase is lost.
Thank you for your time and for cho
ページ6に含まれる内容の要旨
203 Eng Fr Cndn manual 12/21/98 11:19 AM Page 6 Quick Start ™ How to attach IntelliBase USB Hub and Audio to your ® MultiSync brand monitor THE INTELLIBASE USB HUB AND AUDIO WILL ONLY WORK WITH THE MULTISYNC BRAND MONITORS LISTED BELOW. DO NOT ATTEMPT TO CONNECT THE INTELLIBASE WITH ANY OTHER MONITOR BRANDS. MAKE SURE THE MONITOR IS DISCONNECTED FROM THE SYSTEM AND IS UNPLUGGED FROM THE WALL OUTLET BEFORE ANY WORK IS DONE ON THE MONITOR. FOR ALL 21” MULTISYNC MONITORS IT IS ADVISED THAT TWO P
ページ7に含まれる内容の要旨
203 Eng Fr Cndn manual 12/21/98 11:19 AM Page 7 ® MultiSync Monitor Model Names MultiSync 50, MultiSync 70, XV15 and XV15+ Step 1 With the monitor MONITOR IN POSITION TO REMOVE THE BASE AND ATTACH unplugged from your INTELLIBASE USB HUB AND AUDIO system and the wall BASE outlet, carefully turn the monitor upside down on a firm table so that the base is facing up as shown in Figure 1. Figure 1 Step 2 Using a Phillips screwdriver, remove the screw securing the original base to the monitor as sh
ページ8に含まれる内容の要旨
203 Eng Fr Cndn manual 12/21/98 11:20 AM Page 8 Figure 2B Step 3 Locate Adapter Plate “A” that is supplied with ADAPTER PLATE (A) ™ the IntelliBase GUIDE SPINDLE THROUGH CENTER SPINDLE and secure it to HOLE ON ADAPTER PLATE (A) the spindle using the screw that was removed in Step 2 as shown in Figure 2B. Step 4 Locate the two Figure 2C screws that are supplied with INTELLIBASE ROTATE ADAPTER the IntelliBase (BOTTOM VIEW) PLATE UNTIL IT ALIGNS WITH and attach the THROUGH HOLES IntelliBase to
ページ9に含まれる内容の要旨
203 Eng Fr Cndn manual 12/21/98 11:20 AM Page 9 ® MultiSync Monitor Model Names MultiSync XE15, XE17, XP15, XP17, XV17, XV17+, A500, A500+ A700, A700+, A900, E500, E700, E900, E900+, M500, M700 and P750 MONITOR IN POSITION TO Step 1 With the monitor REMOVE THE BASE AND ATTACH INTELLIBASE USB HUB AND AUDIO unplugged from your system and wall BASE outlet, carefully turn the monitor upside down on a firm table so that the base is facing up as shown in Figure 1. Figure 1 Step 2 Using your thumbs,
ページ10に含まれる内容の要旨
203 Eng Fr Cndn manual 12/21/98 11:20 AM Page 10 ORIGINAL MOUNTING Step 3 Using a Phillips screwdriver, remove Figure 3B the screw securing RETAIN the two base halves THESE PARTS TO together as shown USE IN NEW in Figure 3B. MOUNTING Retain the screw and black nylon washer for use in the next step. NEW MOUNTING Step 4 Locate Adapter Plate “B” that is supplied with Figure 3C ™ the IntelliBase and BASE secure it to the spindle using the screw and black nylon washer that was removed in Step 2 AD
ページ11に含まれる内容の要旨
203 Eng Fr Cndn manual 12/21/98 11:20 AM Page 11 Step 6 Locate the two screws that Figure 3E are supplied with the IntelliBase INTELLIBASE and attach ROTATE ADAPTER (BOTTOM VIEW) PLATE UNTIL IT ™ the IntelliBase ALIGNS WITH THROUGH HOLES to the adapter ON THE BASE plate and monitor as shown in Figure 3E. ® Proceed to Page 10 to connect your MultiSync monitor with IntelliBase USB Hub and Audio to your system. MultiSync Monitor Model Names MultiSync XE21, XP21, E1100, E1100+, P1150 and P1250+ F
ページ12に含まれる内容の要旨
203 Eng Fr Cndn manual 12/21/98 11:20 AM Page 12 Step 2 Using a Phillips screwdriver, remove the three screws securing the original base to the monitor. Remove the base by sliding and lifting as shown in Figure 4A. Save these screws for use in Steps 6 and 7. Save the original base for possible future use. Figure 4A ORIGINAL MOUNTING Figure 4B Step 3 Using a Phillips screwdriver, remove RETAIN the screw securing THESE PARTS TO the two base USE IN NEW halves together MOUNTING as shown in Figure
ページ13に含まれる内容の要旨
203 Eng Fr Cndn manual 12/21/98 11:20 AM Page 13 Step 5 After the adapter plate has been attached to Figure 4D the base, snap the base assembly to the monitor. To accomplish this, position all the locking tabs on the base so they mate with the holes in the monitor. Slide the base assembly in place as shown in Figure 4D. Step 6 Using two of the screws that were Figure 4E removed in Step 2, attach the adapter plate assembly to the monitor. To accomplish this, it will be necessary to turn the ad
ページ14に含まれる内容の要旨
203 Eng Fr Cndn manual 12/21/98 11:20 AM Page 14 Step 8 Locate the two Figure 4G screws that are supplied with INTELLIBASE ™ ROTATE ADAPTER the IntelliBase (BOTTOM VIEW) PLATE UNTIL IT and attach the ALIGNS WITH THROUGH HOLES IntelliBase to ON THE BASE the adapter plate and monitor as shown in Figure 4G. ® Proceed below to connect your MultiSync monitor with the IntelliBase USB Hub and Audio to your system. How to connect your MultiSync monitor with IntelliBase USB Hub and Audio to your syste
ページ15に含まれる内容の要旨
203 Eng Fr Cndn manual 12/21/98 11:20 AM Page 15 Step 2 Connect one end of the supplied USB cable to the USB input jack ™ on the rear of the IntelliBase (Detail B) and the other end to the USB output jack of your computer system (Detail A) as shown in Figure 6. Figure 6 – REAR VIEW DETAIL A AUDIO LINE USB SERIES B OUTPUT CONNECTOR DETAIL B SEE DETAIL A SEE DETAIL B Figure 7 Step 3 Connect one end of the supplied AC adapter to the DC input jack on the rear of the IntelliBase and the other end
ページ16に含まれる内容の要旨
203 Eng Fr Cndn manual 12/21/98 11:20 AM Page 16 Note: Steps 5-15 describe USB driver installation for the ® Windows 98 operating system. Other operating systems which support USB may follow a different procedure. Step 5 Turn your computer on. The computer will automatically recognize ™ your IntelliBase . The Add New Hardware Wizard will search for, locate and install the USB Controller and Hub Device drivers needed by the IntelliBase. Step 6 Click on Next > button to begin driver installati
ページ17に含まれる内容の要旨
203 Eng Fr Cndn manual 12/21/98 11:20 AM Page 17 Step 7 Select Search for the best driver for your device and then click the Next > button. Step 8 Click Next > button to select default driver location. 13
ページ18に含まれる内容の要旨
203 Eng Fr Cndn manual 12/21/98 11:20 AM Page 18 Step 9 Click on Next > button to install drivers. The Add New Hardware Wizard will copy the necessary files and install the drivers. ® Step 10 Insert the Windows 98 CD-ROM and then click OK. The required files are copied from the Windows 98 CD-ROM. Note: Depending on system configuration this message may not appear. 14
ページ19に含まれる内容の要旨
203 Eng Fr Cndn manual 12/21/98 11:20 AM Page 19 Step 11 The Hub software has been successfully loaded. Please proceed to Step 12 to load the USB Composite Device. Step 12 Click on Next > button to begin USB Composite Device driver installation. Proceed to follow the screen prompts as previously completed in Steps 5 – 11 to complete installation of the USB Composite Device. 15
ページ20に含まれる内容の要旨
203 Eng Fr Cndn manual 12/21/98 11:20 AM Page 20 Step 13 Click on Next > button to begin USB Human Interface Device driver installation. Proceed to follow the screen prompts as previously completed in Steps 5 – 11 to complete installation of the USB Human Interface Device. Step 14 Click on Next > button to begin USB Audio Device driver installation. Proceed to follow the screen prompts as previously completed in Steps 5 – 11 to complete installation of the USB Audio Device. 16
