ページ1に含まれる内容の要旨
OPERATING INSTRUCTIONS
FP-1600
FieldPoint 10/100 Ethernet
Network Module
These operating instructions describe the installation, features, and
characteristics of the FP-1600. For more detailed information on
using the network module, refer to the FP-1600 user manual.
Features
The FP-1600 is a FieldPoint network module with the following
features:
• Autonegotiating 10/100 Ethernet network interface
• Built-in high efficiency power supply powers I/O modules
• Network watchdog timer
• SnapShot c
ページ2に含まれる内容の要旨
• Terminal bases and I/O modules, complete list of terminal bases and I/O modules in the National Instruments online catalog at www.natinst.com •Cables • 24 VDC power supply Installation Caution To avoid damaging the FP-1600 and the terminal bases, make sure that power is not applied to the FP-1600 while you install or remove terminal bases. Follow these steps to install the FP-1600: 1. Use a flat-bladed screwdriver to open the DIN rail clip to the unlocked position, as shown in Figure 1.
ページ3に含まれる内容の要旨
Local Bus Connector Lip 35 mm DIN Rail Cover Press Figure 2. Mounting the FP-1600 onto a DIN Rail b. Slide the FP-1600 to the desired position along the DIN rail. c. Lock the FP-1600 to the DIN rail by pushing the rail clip to the locked position. • Installing onto a panel mount accessory, which you can order separately from National Instruments: a. Snap the panel mount accessory onto the module, as shown in Figure 3. Press Figure 3. Mounting the FP-1600 onto a Panel Mount Accessory
ページ4に含まれる内容の要旨
b. Lock the panel mount accessory into place by pushing the rail clip to the locked position. c. Mount the FP-1600 and panel mount accessory onto the desired surface. You can drill pilot holes using the directions in the FieldPoint Network Module Panel Mount Accessory installation guide. 3. Add terminal bases with their local bus connectors firmly mated to the FP-1600 local bus connector. 4. Place the protective cover over the local bus connector of the last terminal base in the bank. Fig
ページ5に含まれる内容の要旨
FieldPoint Bank Status Indicators Ethernet Status Indicators RJ-45 Ethernet Port Power Connector Figure 5. Power and Ethernet Connectors on the FP-1600 Cabling If you need to build your own cables, the following table shows the standard ethernet cable wiring connections for both normal and crossover cables. Table 1. Ethernet Cable Wiring Connections Connector 2 Connector 2 Pin Connector 1 (Normal) (Crossover) 1 white/orange white/orange white/green 2 orange/white orange/white green/white 3
ページ6に含まれる内容の要旨
Figure 6 shows the connector pinouts for FieldPoint Ethernet cables. Connector 1 Connector 2 pin 1 pin 8 pin 1 pin 8 Figure 6. Ethernet Cable Powering the FP-1600 Caution Connect the FP-1600 to the terminal base before applying power to the FP-1600 to avoid damaging the FP-1600 or a terminal base. Each FP-1600 on your network requires an 11–30 VDC power supply. The FP-1600 filters and regulates this supplied power and provides power for all the I/O modules in the bank. Therefore, you do
ページ7に含まれる内容の要旨
v v v c c c 11-30 VDC V + Backup Power To adjacent device – Supply (optional connection) (optional) C 11-30 VDC + Primary Power – Supply Figure 7. FP-1600 Power Connector Pinout Connect the primary power supply to the center V and C pair. You can connect an optional backup power supply to the left V and C pair. The right V and C pair provides a convenient means of connecting power to the V and C terminals of a terminal base. Figure 7 shows this optional connection. Specifications Network
ページ8に含まれる内容の要旨
Compliance Electrical safety ................................designed to meet IEC 1010 EMI emissions/immunity..................CISPR 11 CE Mark Compliance This product meets applicable EU directive(s) as follows: EMC directive Immunity ....................................EN 50082–1:1994 Emissions ..................................EN 55011:1991 Group I Class A at 10 meters Mechanical Dimensions Figure 8 shows the mechanical dimensions of the FP-1600. Dimensions are given in inches [millimeters
