ページ1に含まれる内容の要旨
™
PXI
PXI-PCI 8330 Series
User Manual
MXI-3 Multi-System Extension Interface for PCI,
CompactPCI, and PXI Bus Computers
PXI-PCI 8330 Series User Manual
July 2000 Edition
Part Number 370251A-01
ページ2に含まれる内容の要旨
Support Worldwide Technical Support and Product Information www.ni.com National Instruments Corporate Headquarters 11500 North Mopac Expressway Austin, Texas 78759-3504 USA Tel: 512 794 0100 Worldwide Offices Australia 03 9879 5166, Austria 0662 45 79 90 0, Belgium 02 757 00 20, Brazil 011 284 5011, Canada (Calgary) 403 274 9391, Canada (Ontario) 905 785 0085, Canada (Québec) 514 694 8521, China 0755 3904939, Denmark 45 76 26 00, Finland 09 725 725 11, France 01 48 14 24 24, Germany 089 741 31 3
ページ3に含まれる内容の要旨
Important Information Warranty The PXI-PCI 8330 Series hardware is warranted against defects in materials and workmanship for a period of one year from the date of shipment, as evidenced by receipts or other documentation. National Instruments will, at its option, repair or replace equipment that proves to be defective during the warranty period. This warranty includes parts and labor. The media on which you receive National Instruments software are warranted not to fail to execute programming i
ページ4に含まれる内容の要旨
Compliance FCC/Canada Radio Frequency Interference Compliance* Determining FCC Class The Federal Communications Commission (FCC) has rules to protect wireless communications from interference. The FCC places digital electronics into two classes. These classes are known as Class A (for use in industrial- commercial locations only) or Class B (for use in residential or commercial locations). Depending on where it is operated, this product could be subject to restrictions in the FCC rules. (In Cana
ページ5に含まれる内容の要旨
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. Canadian Department of Communications This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations. Cet appareil numérique de la classe B respecte toutes les exigences du Règlement sur le matériel brouilleur du Canada. European Union - Compliance to EEC Directives Reader
ページ6に含まれる内容の要旨
Contents About This Manual Conventions ...................................................................................................................ix Related Documentation..................................................................................................x Chapter 1 Introduction About the MXI-3 System...............................................................................................1-1 Description and Features .....................................................
ページ7に含まれる内容の要旨
Contents Appendix B Technical Support Resources Glossary Index Figures Figure 2-1. Installing the PCI MXI-3 ...................................................................... 2-3 Figure 2-2. PXI MXI-3 Before Installation as Secondary....................................... 2-5 Figure 3-1. MXI-3 Block Diagram.......................................................................... 3-2 Figure 3-2. Basic MXI-3 Configurations................................................................. 3-3 F
ページ8に含まれる内容の要旨
About This Manual This manual describes the features, functions, and operation of the PXI-PCI 8330 Series. The four products in this series are the PCI-8330, the PXI-8330, the PCI-8335, and the PXI-8335. The PXI-PCI 8330 Series incorporates MXI-3 technology, which couples two physically separate PCI, CompactPCI, or PXI buses with a data link capable of 1.5 Gbit/s serial data rates. Conventions The following conventions appear in this manual: This icon denotes a note, which alerts you to importan
ページ9に含まれる内容の要旨
About This Manual Related Documentation The following documents contain information that you might find helpful as you read this manual: Set Up Your MXI-3 System Your computer or chassis documentation PXI Specification, revision 1.0 PCI Specification,revision2.2 PCI-PCI Bridge Architecture Specification,revision1.0 PICMG CompactPCI 2.0 R2.1 specification PXI chassis and documentation (PXI bus systems only) PXI-PCI 8330 Series User Manual x www.ni.com
ページ10に含まれる内容の要旨
1 Introduction This chapter describes the PXI-PCI 8330 Series, lists what you need to get started, and explains how to unpack and set up your hardware. The four products in this series are the PCI-8330, the PXI-8330, the PCI-8335, and the PXI-8335. The PXI-PCI 8330 Series incorporates MXI-3 technology. The terms MXI-3, MXI-3 card and MXI-3 system in this manual refer to both the PCI MXI-3 and PXI MXI-3 cards and systems, unless otherwise noted. About the MXI-3 System Description and Features MXI
ページ11に含まれる内容の要旨
Chapter 1 Introduction Software Transparency Because the MXI-3 system is a PCI-PCI bridge, all devices on the system appear as local devices in a single PCI system. You do not need to rewrite your device drivers for operation on a MXI-3 system. High Performance MXI-3 supports write posting and read prefetching to enhance performance. MXI-3 buffers and retimes the signals between the buses, maintaining the tight timing and high performance PCI requires. What You Need to Get Started To set up and
ページ12に含まれる内容の要旨
2 Installation This chapter explains how to install the MXI-3 software and hardware. Software Installation Your MXI-3 kit includes a setup program for Microsoft Windows operating systems. The setup program works in the same manner for Windows 2000/NT4/9x. Users of other operating systems can ignore this section. Note The software included for Microsoft Windows is provided so that the performance of National Instruments PXI modules is optimized across a PCI-PCI bridge. The software does not affec
ページ13に含まれる内容の要旨
Chapter 2 Installation Hardware Installation The following are general instructions for installing the PCI MXI-3 and PXI MXI-3 cards. Consult your computer user manual or technical reference manual for specific instructions and warnings. Installing a PCI MXI-3 Card 1. Turn off your computer, but leave it plugged in while installing the PCI-MXI-3 card. The power cord grounds the chassis and protects it from electrical damage while you install the module. Warning To protect both yourself and the c
ページ14に含まれる内容の要旨
Chapter 2 Installation 8. Replace the computer cover. 4 3 2 1 1PCIBusSlot 3 PCI Bus Card-Edge Connector 2 Cut-Outs 4 PCI MXI-3 Board Figure 2-1. Installing the PCI MXI-3 Installing a PXI MXI-3 Card Follow these steps to install the PXI MXI-3 in your PXI or CompactPCI chassis. 1. Turn off your PXI or CompactPCI chassis, but leave it plugged in while installing the PXI MXI-3 card. The power cord grounds the chassis and protects it from electrical damage while you install the module. 2. Select a sl
ページ15に含まれる内容の要旨
Chapter 2 Installation 3. Remove or open any doors or covers blocking access to the slot in which you intend to install the PXI MXI 3. 4. Touch the metal part of the case to discharge any static electricity that might be on your clothes or body. 5. Make sure the injector/ejector handle is in its downward position. Align the PXI MXI-3 card with the card guides on the top and bottom of the system controller slot. Caution Do not raise the injector/ejector handle as you insert the PXI MXI-3 card. It
ページ16に含まれる内容の要旨
ON STANDBY 1 2 3 4 5 6 7 8 Chapter 2 Installation Figure 2-2 shows a PXI MXI-3 card just before installation in the system controller slot of a National Instruments PXI-1000 mainframe. PXI/CompactPCI Chassis PXI MXI-3 PXI/CompactPCI Slot 1 Ejector Handle in Down Position Figure 2-2. PXI MXI-3 Before Installation as Secondary Cabling 1. Connect the appropriate serial cable to both primary and secondary MXI-3 cards. If you are using a fiber-optic cable, be sure to remove the protective caps from t
ページ17に含まれる内容の要旨
3 Hardware Overview This chapter presents an overview of the hardware functions of your MXI-3 system, and explains the operation of each functional unit. Functional Overview The MXI-3 system is a PCI-PCI bridge that needs no software for normal operation. When the desktop PC or the CompactPCI/PXI controller powers on, the system BIOS scans its local PCI bus for devices. When it finds the primary interface of the MXI-3 card, it initiates configuration cycles and searches for PCI devices on the se
ページ18に含まれる内容の要旨
Chapter 3 Hardware Overview Parallel- Serial to-Serial Transmitter Data Port Converter C P P P X C PCI/PXI Copper/ C I I Interface Fiber-Optic I B Port Transceiver u s Serial- Receiver Serial to-Parallel Port Data Converter Figure 3-1. MXI-3 Block Diagram MXI-3 Chassis Expansion By plugging a PXI MXI-3 module into any slot other than Slot 1 of a PXI/CompactPCI chassis and a PXI MXI-3 module into Slot 1 of an additional PXI/CompactPCI chassis and connecting them with a cable, one PXI/CompactPCI c
ページ19に含まれる内容の要旨
Chapter 3 Hardware Overview PC to PXI/CompactPCI PXI/CompactPCI to PXI/CompactPCI Figure 3-2. Basic MXI-3 Configurations Because MXI-3 complies with the standard PCI-to-PCI bridging specification, it can take advantage of a variety of other extension configurations. Figure 3-3 shows how MXI-3 can be used to daisy-chain multiple systems in row, all under the control of the primary system, in this case a PC. © National Instruments Corporation 3-3 PXI-PCI 8330 Series User Manual
ページ20に含まれる内容の要旨
Chapter 3 Hardware Overview Star configurations are also possible using MXI-3 interfaces in the primary system to fine tune performance. Daisy-Chain Configuration Star Configuration Figure 3-3. Additional MXI-3 Configurations Functional Unit Descriptions National Instruments MXI-3 ASIC The MXI-3 ASIC, which contains most of the logic in the two-board system, is a PCI master/slave device using the PCI-PCI bridge register set. MXI-3 uses data queues to store data for transmission, and also uses da
