ページ1に含まれる内容の要旨
MultiModem® GPRS
External Wireless USB Modem
Data/Fax/Voice
MTCBA-G-UF1
MTCBA-G-UF2
User Guide
ページ2に含まれる内容の要旨
User Guide for MultiModem® GPRS External Data/Fax/Voice USB Wireless Modem Models MTCBA-G-UF1 & MTCBA-G-UF2 P/N S000346F, Revision F Copyright © 2006 by Multi-Tech Systems, Inc. All rights reserved. This publication may not be reproduced, in whole or in part, without prior expressed written permission from Multi-Tech Systems, Inc. Multi-Tech Systems, Inc. makes no representation or warranties with respect to the contents hereof and specifically disclaims any implied warrant
ページ3に含まれる内容の要旨
Contents CHAPTER 1: PRODUCT DESCRIPTION AND SPECIFICATIONS .................................................................5 PRODUCT DESCRIPTION ..............................................................................................................................................5 Package Contents...................................................................................................................................................5 Interfaces.......................
ページ4に含まれる内容の要旨
SAFETY.....................................................................................................................................................................37 General Safety ......................................................................................................................................................37 Vehicle Safety .......................................................................................................................................
ページ5に含まれる内容の要旨
Chapter 1 – Description & Specifications Chapter 1: Product Description and Specifications Product Description The Multi-Tech MultiModem® GPRS is an external data/fax/voice wireless modem with an USB interface. It also supports mobile originated short message service (SMS) and mobile-terminated SMS. Designed for global use, it offers standards-based multi-band GSM/GPRS Class 10 performance. This ready-to-deploy, standalone modem allows developers to add wireless communication to produc
ページ6に含まれる内容の要旨
Chapter 1 – Description & Specifications Antenna/RF Specifications GSM 850 Frequency RX 869 to 894 MHz Frequency TX 824 to 849 MHz RF Power Stand 2W at 12.5% duty cycle Impedance 50 ohms <2 VSWR Typical Radiated Gain 0 dBi on azimuth plane GSM 1800 GSM 1900 Frequency RX 1805 to 1880 MHz 1930 to 1990 MHz Frequency TX 1710 to 1785 MHz 1850 to 1910 MHz RF Power Stand 1W at 12.5% duty cycle 1W at 12.5% duty cycle Impedance 50 ohms <2 VSWR Typical Radiated Gain 0 dBi on azi
ページ7に含まれる内容の要旨
Chapter 1 – Description & Specifications Features • GPRS Class 10 operation • Dual-band 850/1900 or 900/1800 GSM/GPRS • GSM Class 1 and Class 2 Group 3 FAX • Desktop or panel mounting • Short Message Services including text and PDU, point-to-point, cell broadcast • 14.4K GSM circuit switched data • SMA antenna connector and SIM socket • Serial interface supports DTE speeds to 115.2K • AT command compatible • MNP2 V.42bis data compression • Numerous LEDs provide operational status
ページ8に含まれる内容の要旨
Chapter 1 – Description & Specifications Application Overview Application Types With circuit switched data rates up to 14.4K bps, the MultiModem® GPRS is targeted at applications that periodically need to send or receive data over a wireless network. It is an ideal solution for: Appliances ATM Terminals Automotive Data Collection Gas Pumps Industrial and Medical Remote Monitoring Systems Remote Diagnostics Remote Metering Security Systems Vending/Gaming Machines Other devices
ページ9に含まれる内容の要旨
Chapter 1 – Description & Specifications Benefits/Features in Applications Short Development Time. The MultiModem® GPRS can make your existing and next generation device, machine, or system, communication-ready without requiring any hardware changes to its design. It actually provides faster time-to-market because it relieves the burden and expense of obtaining network and RF approvals. This complete, ready-to-deploy wireless modem allows you to enhance your product while you focus on d
ページ10に含まれる内容の要旨
Chapter 1 – Description & Specifications Functions – GSM Modes MODE DESCRIPTION Standard Dual Band Extended GSM 900 MHz Class 4 (2W) and GSM 1800/1900 MHz Class 1 (1W) Interface USB 12 Mbps. AT command set based on V.25ter and GSM 07.05 & 07.07 SMS Mobile Originated (MO) and Mobile Terminated (MT) SMS Mode Text & PDU point to point. Cell broadcast in accordance with GSM 07.05. Data Asynchronous 2400, 4800, 9600 and 14400 bps. Data Transparent and Non Transparent modes. In Non Transp
ページ11に含まれる内容の要旨
Chapter 1 – Description & Specifications Specifications General Specifications Mechanical Dimensions & Weight 4.3" w x 2.4" h x 0.94" d; 3.6 oz. (11 cm x 6.1 cm x 2.4 cm; 102 g) Connectors & Fasteners Antenna Connection type: SMA jack Data/Power Connector: USB Series A receptacle Phone Handset: Modular Handset Jack SIM receptacle: (standard) Operating Temperatures 0 to +50°C Humidity Relative humidity 20% to 90% noncondensing Certifications CE Mark EMC: FCC Part 2, 15, 22, 24,
ページ12に含まれる内容の要旨
Chapter 1 – Description & Specifications LED Indicators TD. Transmit Data. Lit when modem is transmitting data. RD. Receive Data. Lit when modem is receiving data. CD. Carrier Detect. Lit when data connection has been established. LS. Line Status. Continuous “on” state indicates that the wireless modem is not registered on the network. Flashing state indicates registration on network. Off state. Modem is off (not ready) or in download mode. TR. Terminal Ready. Commonly call
ページ13に含まれる内容の要旨
Chapter 2 – Installation Chapter 2: Installation Mechanical Mounting To mount the Wireless MultiModem, do the following: 1. Obtain mounting screws (two are needed) that are appropriate for the surface on which you will mount the MultiModem. For example, one might use two 6-32 self-tapping screws 5/8” in length to mount the unit in a truck to the wall of the cab behind the passenger’s seat. 2. Typically, the unit is mounted against a flat surface into which holes can be drilled. The
ページ14に含まれる内容の要旨
Chapter 2 – Installation 3. Slide the mounting brackets into the corresponding slots on the backside of the MultiModem chassis. NOTE: Some MultiModem units will be shipped with a single mounting bracket. Slide it through the channel on the MultiModem chassis and secure it with screws. 4. Attach the MultiModem with two screws to the mounting surface at the desired location on the equipment. Multi-Tech Systems, Inc. MultiModem® GPRS with USB User Guide 14
ページ15に含まれる内容の要旨
Chapter 2 – Installation Inserting SIM/R-UIM Card into Holder (GSM Only) The wireless MultiModem requires a SIM card (Subscriber Identity Module) to operate on a GSM network. Some CDMA networks, mostly in China, require an R-UIM card (Removable User Identity Module). To install the card, do the following: 1. Using your fingernail or a small wedging tool (e.g., a small screwdriver), pry off the SIM cover. 2. Insert the SIM card into the holder. 3. Verify that the SIM card fits into
ページ16に含まれる内容の要旨
Chapter 2 – Installation Connecting the Antenna Connect a suitable antenna to the SMA connector (see “Antenna/RF Specifications” in the User Guide). Antenna Connector (SMA Type) Multi-Tech Systems, Inc. MultiModem® GPRS with USB User Guide 16
ページ17に含まれる内容の要旨
Chapter 2 – Installation Installing Software The wireless USB MultiModem drivers need to be installed in your computer’s program directory. The procedure differs depending on the operating system. This section provides installation procedures for Windows Operating Sytems (Win 98/ME/2000/2003/XP). Linux Operating System drivers are also located on the CD in the Linux_Install directory. Three install wizards guide you through the software Installation. In the following installation process,
ページ18に含まれる内容の要旨
Chapter 2 – Installation Part B: Installing the USB Driver 3. Connect the USB cable between the MultiModem and the PC. 4. After a brief delay, the Welcome to the Found New Hardware Wizard screen appears referring to the TUSB3410 Serial Port device. This is the first of three New Hardware Wizards that will appear. Click on Install from a list or specific location (Advanced). Click Next. 5. Please choose your search and installation options screen appears. Ensure that Search for t
ページ19に含まれる内容の要旨
Chapter 2 – Installation Part C: Associating PC Port with USB Driver 8. Wait while Windows prepares the next phase of the installation (associating the PC port with the USB drive). The Welcome to the Found New Hardware Wizard screen will appear with the Texas Instruments UMP Serial Port as the device to be installed. This is the beginning of the “Found New Hardware” sequence for the port. Click Install from a list or specific location (Advanced). Click Next. 9. Please choose your s
ページ20に含まれる内容の要旨
Chapter 2 – Installation Part D: Installing the Modem INF File 12. Wait while Windows prepares the final phase of the installation.The Welcome to the Found New Hardware Wizard screen appears for the MultiTech – GSM Modem. Click on Install from a list or specific location (Advanced). Then click Next. 13. The Please choose your search and installation options screen appears. Ensure that Search for the best driver in these locations is set and click on Search removable media (floppy,
