ページ1に含まれる内容の要旨
User’s
Guide
LSI21003
PCI to Dual Channel SCSI
Host Adapter
Version 1.0
October 2000
®
S14051
ページ2に含まれる内容の要旨
Electromagnetic Compatibility Notices This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference, and 2. This device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable prote
ページ3に含まれる内容の要旨
This document contains proprietary information of LSI Logic Corporation. The information contained herein is not to be used by or disclosed to third parties without the express written permission of an officer of LSI Logic Corporation. LSI Logic products are not intended for use in life-support appliances, devices, or systems. Use of any LSI Logic product in such applications without written consent of the appropriate LSI Logic officer is prohibited. Document DB15-000165-00, First Edition (Octob
ページ4に含まれる内容の要旨
iv
ページ5に含まれる内容の要旨
Preface This book is the primary reference and user’s guide for the LSI Logic LSI21003. It describes how to install and configure the LSI21003 in a PCI computer system. LSI Logic Technical Support The entire LSI Logic host adapter solution has been designed for ease of use. However, if you require additional assistance, please contact the LSI Logic Technical Support Hot Line at (719) 533-7230. The hours of operation are from 7:30 a.m. to 4:30 p.m. (MST), Monday through Friday. You may also send
ページ6に含まれる内容の要旨
• Chapter 3, Technical Specifications, describes the physical and operational environments of the LSI21003. • Appendix A, Glossary of Terms and Abbreviations, provides definitions of various terminology that is referenced throughout this user’s guide. Related Publications LSI53C1010-33 PCI to Dual Channel Ultra3 SCSI Multifunction Controller Technical Manual, Order Number S14025.A PCI Storage Device Management System SDMS™ 4.0 User’s Guide, Order Number S14007.A Revision Record Revision Date Rem
ページ7に含まれる内容の要旨
Contents Chapter 1 Using the LSI21003 1.1 General Description 1-1 1.2 Features 1-2 1.2.1 PCI Interface 1-2 1.2.2 SCSI Interface 1-2 1.2.3 Board Characteristics 1-3 1.3 Interface Descriptions 1-3 1.3.1 The PCI Interface 1-3 1.3.2 The SCSI Interface 1-4 1.3.3 SCSI Activity LED Interface 1-5 1.3.4 Cabling 1-5 Chapter 2 Installing the LSI21003 2.1 Quick Installation Procedure 2-1 2.2 Detailed Installation Procedure 2-3 2.2.1 Before You Start 2-3 2.2.2 Inserting the Host Adapter 2-4 2.2.3 Connecting
ページ8に含まれる内容の要旨
3.1.5 Safety Characteristics 3-4 3.2 Operational Environment 3-4 3.2.1 The PCI Interface 3-4 3.2.2 The SCSI Interface 3-7 3.3 Subsystem and Subsystem Vendor ID 3-12 Appendix A Glossary of Terms and Abbreviations Index Customer Feedback Figures 2.1 Hardware Connections for the LSI21003 2-5 2.2 Inserting the Host Adapter 2-6 2.3 SCSI Cables 2-7 2.4 Internal SCSI Ribbon Cable to Host Adapter 2-8 2.5 Internal SCSI Ribbon Cable to Internal SCSI Device Connection 2-9 2.6 Connecting Additional Internal
ページ9に含まれる内容の要旨
3.2 PCI Connector J1 Front Side Signals 3-5 3.3 PCI Connector J1 Back Side Signals 3-6 3.4 SCSI Connector J2, Channel A, Internal 3-8 3.5 SCSI Connector J3, Channel A, External 3-9 3.6 SCSI Connector J4, Channel A, Internal 3-10 3.7 SCSI Connector J5, Channel B, Internal 3-11 3.8 Connector J6 Signals 3-12 3.9 Subsystem and Subsystem Vendor ID 3-12 Contents ix
ページ10に含まれる内容の要旨
xContents
ページ11に含まれる内容の要旨
Chapter 1 Using the LSI21003 This chapter provides an overview of the LSI Logic LSI21003 PCI to Dual Channel SCSI Host Adapter board and its interfaces to PCI computer systems. These topics are discussed: • Section 1.1, “General Description,” page 1-1 • Section 1.2, “Features,” page 1-2 • Section 1.3, “Interface Descriptions,” page 1-3 1.1 General Description The LSI21003 provides internal and external SCSI interfaces to PCI computer systems that require BIOS support on the add-in SCSI adapter.
ページ12に含まれる内容の要旨
1.2 Features This section provides a high level overview of the PCI Interface, the SCSI Interface, and Board Characteristics for the LSI21003. 1.2.1 PCI Interface The PCI interface includes these features: • True PCI multifunction controller for maximum performance • 32-bit (33 MHz) DMA bus master • Bursts up to 128 Dwords across the PCI Bus • Zero wait-state bus master data bursts up to 110 Mbytes/s (@ 33 MHz) • Prefetches up to 8 Dwords of SCRIPTS™ instructions • PCI Universal 3.3 V/5 V bus su
ページ13に含まれる内容の要旨
• Fast, Ultra, Ultra2, and Ultra160 data transfer capability • SCSI Termination Power (TERMPWR) source with autoresetting circuit breaker • Supports SE and LVD signaling with automatic termination – Channel A is SE only with autosense termination – Channel B is SE or LVD with termination permanently enabled • Performs complex bus sequences without interrupts, including restore data pointers • SCSI Plug and Play • Flash ROM for BIOS storage • Serial EEPROM for each channel for user configuration
ページ14に含まれる内容の要旨
functionality for the LSI21003 is contained within the LSI53C1010-33. The chip connects directly to the PCI bus and generates timing protocol in compliance with the PCI specification. The PCI interface operates as a 32-bit DMA bus master. The connection is made through edge connector J1 (see Figure 2.1). The signal definitions and pin numbers conform to the PCI Local Bus Specification Revision 2.2 standard. The LSI21003 conforms to the PCI universal signaling environment for a 5 V or 3.3 V PCI b
ページ15に含まれる内容の要旨
1.3.3 SCSI Activity LED Interface The SCSI activity LED interface is a four-wire arrangement that allows connection of an LED harness to the board. The connector on the host adapter is J6 for both channels. See Table 3.8 on page 3-12 for the signal name and pin numbers on this interface. 1.3.4 Cabling The cable provided in the kit is matched for a Fast/Ultra/Ultra2/Ultra160 SE or LVD operation. This cable also has built-in multimode (SE/LVD) termination since most Ultra160 hard disk drives are n
ページ16に含まれる内容の要旨
1-6 Using the LSI21003
ページ17に含まれる内容の要旨
Chapter 2 Installing the LSI21003 This chapter describes installing the LSI21003 into PCI computer systems and includes these topics: • Section 2.1, “Quick Installation Procedure,” page 2-1 • Section 2.2, “Detailed Installation Procedure,” page 2-3 • Section 2.3, “Setting SCSI IDs,” page 2-22 • Section 2.4, “Setting Interrupts (Exceptional Cases),” page 2-24 • Section 2.5, “Completing the Installation,” page 2-25 2.1 Quick Installation Procedure This section provides quick setup instructions for
ページ18に含まれる内容の要旨
A 32-bit slot should be used. The LSI21003 will work in a 64-bit slot, but only 32 bits are used. The host adapter requires a PCI slot that allows bus master operation. See Figure 2.2 on page 2-6. Step 6. Remove the blank bracket panel on the back of the computer aligned with the PCI slot you intend to use. Save the bracket screw for securing the installed board. Step 7. Carefully insert edge connector J1 of the host adapter into the PCI slot. Make sure the edge connector is properly aligned bef
ページ19に含まれる内容の要旨
2.2 Detailed Installation Procedure This section provides step-by-step instructions for installing your LSI21003 and connecting it to your SCSI peripherals. If you are experienced in these tasks, you may prefer to use Section 2.1, “Quick Installation Procedure.” If you are not confident that you can perform the tasks as described here, LSI Logic suggests getting assistance. 2.2.1 Before You Start Before you start, look through the task list below to get an overall idea of the steps to perform. •
ページ20に含まれる内容の要旨
2.2.2 Inserting the Host Adapter For safe and proper installation, check the user’s manual supplied with your computer and perform the following steps: Step 1. Ground yourself before removing the host adapter board from its package. Note: Static charges on your body can damage electronic components. Handle plug-in boards by the edge; do not touch board components or gold connector contacts. The use of a static ground strap is recommended. Step 2. Remove the LSI21003 from its packing and verify t
