ページ1に含まれる内容の要旨
Supplement to the RS/6000 7043 43P Series (SA38-0511
and SA38-0512) IBM
Service Guide and User's Guide
SN32-9080-01
ページ2に含まれる内容の要旨
Second Edition (December 2000) Before using this information and the product it supports, read the information in “Appendix. Notices” on page 15. ©International Business Machines Corporation 2000. All rights reserved. Note to U.S. Government Users - Documentation related to restricted rights - Use, duplication, or disclosure is subject to the restrictions set forth in the GSA ADP Schedule Contract with IBM Corp..
ページ3に含まれる内容の要旨
Contents About This Book .......................v ISO 9000..........................v Online Publications.......................v Related Publications ......................v Trademarks .........................v Chapter 1. 7043–140 and 7043–150 Fansink Removal and Replacement Procedures ........................1 Identifying the Fansink Number...................1 Determining the Fansink Assembly Number to be Replaced .........1 7043–140 and 7043–150 Fansink Removal and Replacement Procedures ...
ページ4に含まれる内容の要旨
iv Supplement to the Service Guide and User’s Guide
ページ5に含まれる内容の要旨
About This Book This supplement provides updates to the following publications: v RS/6000 7043 43P Series User’s Guide, SA38-0511 v RS/6000 7043 43P Series Service Guide, SA38-0512 ISO 9000 ISO 9000 registered quality systems were used in the development and manufacturing of this product. Online Publications RS/6000 and pSeries 680 publications are available online. To access the online books, visit our Web site at: http://www.rs6000.ibm.com/resource/hardware_docs/ Related Publications The follo
ページ6に含まれる内容の要旨
vi Supplement to the Service Guide and User’s Guide
ページ7に含まれる内容の要旨
Chapter 1. 7043–140 and 7043–150 Fansink Removal and Replacement Procedures This chapter provides information on replacing defective 7043–140 and 7043–150 fansinks without having to replace the entire system board. Identifying the Fansink Number The following table contains information to help you determine the correct fansink to be replaced on both the 7043–140 and 7043–150 system boards. Obtain the correct fan(s) before going on-site to replace the fansink assembly. The fan that is not used sh
ページ8に含まれる内容の要旨
Table 2. Fansink numbers by System Board Assembly and FRU Numbers (continued). Machine Type FRU Part Numbers System Board Fansink Number Assembly Part Numbers 7043–150 375MHZ 08L8446, 11K0157, 03N2526, 08L1363, 09P1126 New Version System 11K0459 41L5177, 11K0148 11K0464, Board 41L5912, 41L5518 41L5172, 41L5517 41L5590 41L5588, 41L5911 7043–150 375MHZ 11K0459, 41L5912 11K0017, 11K0650 09P1129 New Version System Board 7043–140 and 7043–150 Fansink Removal and Replacement Procedures This section co
ページ9に含まれる内容の要旨
4. To remove the disk drive bracket, refer to the ²Removing Internal Drive² section of the RS/6000 7043–43P Series Service Guide. Carefully place the bracket assembly on top of the power supply (leave the hard files plugged in). Note: Disconect temporarily any PCI Adapter Card installed in slot 5 in order to remove the disk drive bracket. 5. Locate the CPU fansink on the planar under the disk drive and unplug it. Fansink Location 6. Unclip the heatsink by pushing down and away on the finger tab.
ページ10に含まれる内容の要旨
Replacement 1. If you are replacing a fansink 09P1125, install the new component by hooking the side opposite the finger tab and then pushing the finger tab side down until it locks into position. OR If you are replacing a fansink 09P1126, first remove the paper pull tab to expose the thermal grease underneath. Install the new fansink by hooking the side opposite the finger tab and then pushing the finger tab side down until it locks into position. 2. Plug the new fansink into the system board c
ページ11に含まれる内容の要旨
5. Locate and unplug the fan and disconnect the fansink assembly power cable from the CPU fansink connector (J26). Note: There are two possible fansink connections for this system board: right-angle finger tabs, and wire springs. Fansink Location 6. To remove a fansink with right-angle finger tabs, unclip the heatsink by pushing down and away on the fingertab. Remove the fansink assembly and discard. Note: Do not wipe off the remaining thermal grease from the top of the existing CPU chip on the
ページ12に含まれる内容の要旨
Replacement 1. If you are replacing a fansink 09P1126, first remove the paper pull tab to expose the thermal grease underneath. Install the new fansink by hooking the side opposite the finger tab and then pushing the finger tab side down until it locks into position. OR If you are replacing a fansink 09P1129, remove the adhesive protective paper on the bottom of the heatsink and place the fansink assembly into the metal bracket on the system board assembly. Secure the ends of the wire loop under
ページ13に含まれる内容の要旨
Chapter 2. 7043–150 System Features This chapter contains information specific to both the 250MHz and 375MHz options for the Model 150, and applies to the RS/6000 7043 43P Series User’s Guide and the RS/6000 7043 43P Series Service Guide. All other information is consistent with the system books. System Features Bus Architecture Five 32-bit PCI adapter slots are available: v Slots 2 and 3, primary v Slots 1, 4, and 5, secondary Microprocessor v PowerPC 604e 250 MHz with 1MB parity synchronous L2
ページ14に含まれる内容の要旨
Keyboard and Mouse v Standard: 101–Key Enhanced keyboard v Optional: 101/102 or 106–Key Enhanced Keyboard v Standard: 3-button mouse Front-Panel Display v 4-digit LED diagnostics display Input/Output Ports v 25-pin Parallel v 9-pin Serial (2) v 8-pin Tablet v Keyboard v Mouse v Ultra SCSI (16-bit) v 100/10 Base 5 Ethernet v 100/10 Base T Ethernet v Audio Line-in and Audio Line-out v Microphone v Headphone Security Features v Cover lock v Tie-down (optional) v Power-on password v Privileged-acces
ページ15に含まれる内容の要旨
Setting the SCSI Security Jumpers Note: Carefully read and follow the safety guidelines detailed in the corresponding section of the RS/6000 7043 43P Series User’s Guide, SA38-0511. To increase system unit security, the external SCSI connector can be disabled by changing jumpers inside the system unit. 1. Locate the SCSI security jumpers in the following figure. 2. To disable the external SCSI connector, move the jumper on J35 to the front two pins, and move the jumper on J36 to the rear two pin
ページ16に含まれる内容の要旨
System Board Locations for Model 150 B1 Battery connector J1 Wakeup-on-LAN jumper J2 5x5 Auxiliary 5v connector J3 Audio input connector J4 Internal SCSI connector #2 J5 CD-ROM audio connector J6 CD-ROM audio connector J7 Power connector J8 Power connector J10 Media fan connector J11 Memory Connector 1 10 Supplement to the Service Guide and User’s Guide
ページ17に含まれる内容の要旨
J13 Audio output connector J15 Remote Power-up Jumper J16 Diskette drive connector J17 Microphone jack J18 Reset Connector J19 Memory Connector 3 J20 Power-on Password jumper J22 Headphone jack J23 Serial port connector 2 J24 Serial port connector 1 J25 Tablet port connector J26 CPU fansink connector J27 System fan connector J28 Memory Connector 2 J30 System fan connector J32 Privileged-Access Password jumper J33 Internal SCSI 16-bit connector J35 SCSI security jumper J36 SCSI security jumper J3
ページ18に含まれる内容の要旨
System Board, Cables, and Accessories 12 Supplement to the Service Guide and User’s Guide
ページ19に含まれる内容の要旨
Index FRU Number Units Per Assy Description Number 1 09P0168 1 System Board (250 MHz) 2 27F4212 6 Screw 3 39H8697 1 Hex Standoff 4 19L1808 1-4 64MB DIMM 19L1809 1-4 128MB DIMM 29L3302 1-4 256MB DIMM 5 93H1821 1 Diskette Cable Assembly 6 40H7572 1 SCSI Cable Assembly 7 93H6151 1 Ultra Cable Assembly (Optional) 8 08L1417 1 Riser Card 9 07L9115 1 Vertical Stand 10 40H6328 2 9-pin to 25-pin Serial Port Converters 11 11H2168 1 Display Cable Toroid Kit 12 15F8409 1 Battery 13 65G8850 1 CD-ROM drive au
ページ20に含まれる内容の要旨
14 Supplement to the Service Guide and User’s Guide
