ページ1に含まれる内容の要旨
HyperNet
PCI 10/100 TX
HYNEC52001
USER GUIDE
Information in this document is subject to change without
notice. All rights reserved. All brand names are registered
trademarks of their respective companies.
ページ2に含まれる内容の要旨
interference in which case the user will be required to correct the interference at his own expense. European Community (EC) Electromagnetic Compatibility Directive. This equipment has been tested and found to comply with the protections requirements of European Emission Standard EN55022 and the Generic European Immunity Standard EN50082-1. This equipment is designed to operate in a domestic environment and as such is tested to the EN55022 ITE domestic emissions limit. The domestic immunity st
ページ3に含まれる内容の要旨
The HyperNet PCI 10/100 Adapter series is highly integrated and cost-effective single-chip adapter range that provides 32-bit performance, PCI bus master capability, and full compliance with Fast Ethernet 100Base-TX specifications. It also supports full- duplex operation, making possible 200Mbps of bandwidth with no additional cost, when connected to an appropriate switch. The HyperNet PCI 10/100 supports a wide selection of network operating systems, including Window NT, Windows 98, Windows 95,
ページ4に含まれる内容の要旨
Features • PCI 32-Bit bus-mastering architecture speeds data transfers between your PC and the network, without burdening the PC’s processor • Autonegotiation, sensing and switching between 10Mbps and 100Mbps operation • Full Duplex capabilities - Independent receive and transmit circuits allow for full duplex operation at both 10Mbps and 100Mbps, giving the Card a maximum throughput of 200Mbps • A Single RJ-45 female connector supports both 10Mbps and 100Mbps operation • Supports all major Net
ページ5に含まれる内容の要旨
If you do not have each of these items, contact your supplier before proceeding further. Static Electricity Warning Static electricity is accumulated naturally in the human body, and can be discharged through electrical components by touching them. This shock can potentially cause permanent internal damage to the component. When installing the adapter, please observe the following precautions: • Discharge yourself before commencing by touching a grounded metal appliance, such as the metal frame
ページ6に含まれる内容の要旨
• Turn OFF the power to the computer to prevent any accidental damage. • Remove your computer's cover (refer to your computer owner's manual). • Select an available PCI expansion slot which supports Bus Master mode, and remove slot cover. Make a note of the slot number (if one is printed on the motherboard, next to this slot). • Carefully install the adapter by firmly pressing the card into the slot which you have chosen, and applying even pressure until the adapter is completely seated in the
ページ7に含まれる内容の要旨
Configuring the PCI 10/100 Adapter PCI Computer with PnP Auto-Configuration Before installing your Hypertec PCI 10/100 Adapter, try to establish whether your PC has PCI PnP Auto configuration. In most cases, the PCI computer will be configured automatically by the system's BIOS during boot up. The BIOS automatically assigns the I/O base address and IRQ to the card for proper operation. PCI Computer without PnP Self-Configuration In rare cases, some PCI computers require additional configuration
ページ8に含まれる内容の要旨
of BIOS for use with PCI adapters. Checking card operation The Adapter provides two LEDs to indicate operation: FDX (Full Duplex) Steady Green Light indicates the connection to a full duplex switch port. LK/ACT (Link/Activity) Steady Green Light indicates an active connection between the adapter and the hub/switch port. Flashing Green Lights indicates data transmission LINK/ACT(Activity) FDX(Full-D uplex) Figure 2. PCI 10/100Base series Adapter LED indicators LK/ ACT FDX
ページ9に含まれる内容の要旨
driver diskette. For more details of the loading procedure for software drivers, please execute the HELP8139.EXE program. If at any time during installation you experience difficulties, please contact Hypertec Technical Support on +44 1488 686844 (01488 686844 in the UK).
ページ10に含まれる内容の要旨
The setup program can view current configuration and run diagnostics on the HyperNet PCI 10/100 series Adapters. This testing includes three separate procedures: • View Current Configuration • Setup New Configuration • Run diagnostics Menu Adapter cannot connect to the network Make sure that the cable is installed properly. The network cable must be securely attached to all connections. If the cable is attached, but the problem persists, try using a different cable. Note: If you're operating at
ページ11に含まれる内容の要旨
TD 4 5 RD 6 7 8 RD 12345678 Figure A-1 show the PCI 10/100BaseTX RJ-45 Connector Pin Assignments Note: The Pin assignments are identical for 10Base-T and 100Base-TX, by using UTP cable. Network cabling In Fast Ethernet 100Base-TX, the cable, quality, distance, and connectors must comply with the EIA/TIA 568 “Commercial Building Wiring Standard”. IEEE 802.3u Specification: The 100Base-TX specification supports 100 Mbps transmission over two of four pairs of twisted Ethernet wiring. In two pair wi
ページ12に含まれる内容の要旨
ページ13に含まれる内容の要旨
Length - 125.4mm Height - 42.3mm LED Indicators: Full Duplex, Link/Activity Operating Temperature: 0°-55°C (32°F-131°F) Operating Humidity: 0% - 90% non-condensing Storage: -20°C-65°C (-4°F–149°F) Ethernet Protocols: IEEE 802.3U (Fast Ethernet, 100Base-TX) IEEE 802.3 (Ethernet, 10Base-T) Data Transfer Rate: 100 or 10 Mbit/sec 200 or 20Mbit/sec Full Duplex Connector: Unshielded RJ-45 female connector. EMI: FCC Class B European standards EN55022 and EN50082-1
ページ14に含まれる内容の要旨
disaster, misuse, abuse or non-Hypertec modification of the product. Additional components installed by the dealer or end user are not covered by this warranty. Apart from the above, no warranty is expressed or implied, including warranty of merchantability or warranty of fitness for use for a particular purpose. The liability of Hypertec is limited to the repair or replacement of the product with a functionally equivalent or better product. Hypertec is not liable for any accidental, general, sp
