ページ1に含まれる内容の要旨
SPBD-155E4J1RD
Intelligent SFP Bi-Directional Transceiver Module
for Fast Ethernet, ATM, SONET OC-3/SDH STM-1
FEATURES
RoHS compliant
Digital Diagnostic SFF-8472, Rev. 9.5 MSA
compliant
Simplex LC connector with 1310nm
Transmitter and 1550nm Receiver
Single + 3.3V power supply and TTL logic
interface
Bellcore GR-468 compliant
Laser class 1 product which comply with the
requirements of IEC 60825-1 and IEC 60825-2
Description Application
The SPBD-155xxxxx series are ho
ページ2に含まれる内容の要旨
SPBD-155E4J1RD 1. Absolute Maximum Ratings Parameter Symbol Min. Typ. Max. Unit Note Storage Temperature Ts -40 85 ºC Storage Ambient Humidity HA 5 95 % Power Supply Voltage VCC 0 5 V Signal Input Voltage -0.3 Vcc+0.3 V Optical Input Power (Peak) +4 dBm 2. Recommended Operating Conditions Parameter Symbol Min. Typ. Max. Unit Note Operating Case Temperature TC -5 75 ºC Note (1) Non-condensing Ambient Humidity HA 5 85 % Power Supply Voltage VCC 3.135 3.3 3.465 V P
ページ3に含まれる内容の要旨
SPBD-155E4J1RD 4. Specification of Receiver Parameter Symbol Min. Typ. Max. Unit Note Input Optical Wavelength λ 1480 1600 nm PIN-PD IN Receiver Sensitivity P dBm Note (1) IN -31 Input Saturation Power (Overload) P -3 dBm SAT LOS-Deassert Power P - -31 dBm A LOS-Assert Power P -44 dBm Note (2) D LOS Hysteresis P -P 0.5 2 5 dB A D Optical Reflectance -14 dB Note (3) Output Data Rise/Fall time t /t 1.5 ns Note (4) r f S/X Endurance 10 dB Note (5) Optical Isolatio
ページ4に含まれる内容の要旨
SPBD-155E4J1RD 6. Enhanced Digital Diagnostic Interface The memory map in the following describes an extension to the memory map defined in SFP MSA. The enhanced interface uses the two wire serial bus address 1010001X(A2h) to provide diagnostic information about the module’s present operating conditions. 2 wire address 1010000 X (A0h) 2 wire address 1010001 X (A2h) 0 0 Alarm and Warning Thresholds (56 bytes) Serial ID Defined by SFP MSA 55 (96 bytes) 56 Cal Constants (
ページ5に含まれる内容の要旨
SPBD-155E4J1RD 8. Pin Description SFP Transceiver Electrical Pad Layout Host Board Connector Pad Layout Pin Function Definitions Pin Num. Name Function Plug Seq. Notes 1 VeeT Transmitter Ground 1 Note (1) 2 TX Fault Transmitter Fault Indication 3 Note (2) 3 TX Disable Transmitter Disable 3 Note (3) 4 MOD-DEF2 Module Definition 2 3 Note (4), 2 wire serial ID interface 5 MOD-DEF1 Module Definition 1 3 Note (4), 2 wire serial ID interface 6 MOD-DEF0 Module Definitio
ページ6に含まれる内容の要旨
SPBD-155E4J1RD Notes: 1) Circuit ground is internally isolated from frame (chassis) ground. Tx GND and Rx GND may be internally isolated within the TRx module. 2) TX Fault is an open collector/drain output, which should be pulled up with a 4.7K~10K Ω resistor on the host board. Pull up voltage between 2.0V and VccT+0.3V. The output indicates Low when the transmitter is operating normally, and High with a laser fault including laser end-of-life. In the low state, the output will be pull
ページ7に含まれる内容の要旨
SPBD-155E4J1RD 9. Recommend Interface Circuit VCC 3.3V 1uH Protocol Vcc DELTA SFP Module 1uH RES1 10uF 0.1uF VccT 0.1uF 10k Ohms Tx_Disable Tx_Disable Tx_Fault Tx_Fault TD + 0.01uF Laser Driver 100 Ohms Laser Diode TD - 0.01uF VeeT Protocol IC SerDes IC VccR RES1 10uF 0.1uF RD + 0.01uF Preamp & Quantizer 100 Ohms* Photo Diode RD - 0.01uF Rx_LOS Rx_LOS 3.3V VeeR RES1 RES1 RES1 Mod_def 2 PLD / PAL EEPROM Mod_def 1 Mod_def 0 RES1 = 4.7k to 10k Ohms * Depands on SerDes IC used SFP Host Board
ページ8に含まれる内容の要旨
SPBD-155E4J1RD 10. Outline Dimensions Class 1 Laser Product XXXX nm Tx / Rx XXXX nm Week (52Weeks/Year) : 1月2日=01 Transmitter Wavelength Latch Color Identifier 1310nm Black Yellow 1550nm 8 Revision: S1 04/11/2007 www.deltaww.com DELTA ELECTRONICS, INC. Complies with 21 CFR 1040.10 and 1040.11 Made in x FS
ページ9に含まれる内容の要旨
SPBD-155E4J1RD 11. Regulatory Compliance Feature Test Method Reference Performance Electrostatic Discharge Human Body Model MIL-STD-883E Method 3015.7 (ESD) to the Electrical (HBM) EIA-JESD22-A114 Pins (1) Satisfied with Machine Model (MM) EIA-JESD22-A115 Electrostatic Discharge Contact Discharge IEC/EN 61000-4-2 electrical (ESD) to the Simplex IEC/EN 61000-4-2 characteristics of Air Discharge product spec. Receptacle Radio Frequency IEC/EN 61000-4-3 (2) No physical damage Elec
