ページ1に含まれる内容の要旨
Wireless 300N USB Adapter
Model # AWLL6090
User’s Manual
Rev. 1.0
ページ2に含まれる内容の要旨
Table of Contents 1. Introduction .................................................................................................................3 1.1 Package Contents ................................................................................................. 3 1.2 Features ................................................................................................................ 3 2. Installation ................................................................................
ページ3に含まれる内容の要旨
1. Introduction Congratulations on your purchase of the Wireless 300N USB Adapter. Its high bandwidth combined with extended wireless coverage delivers fast and reliable connection for all of your networking applications when used with Airlink101® Wireless 300N Gigabit Router to achieve up to 300Mbps* data rate. A full range of security features such as WEP, WPA-PSK, and WPA2-PSK provide the highest level of wireless network security. The bundled Wireless Utility allows you to set up
ページ4に含まれる内容の要旨
2. Installation This section provides instructions on how to install the Wireless 300N USB Adapter. The driver is installed along with the utility. Step 1 Insert the USB adapter into an available USB port on your computer. Step 2 Windows will launch the Found New Hardware Wizard. The Found New Hardware Wizard appears differently depending on your operating system. Click Cancel to quit the wizard and insert the Installation CD into your CD drive. Step 3 The Autorun sc
ページ5に含まれる内容の要旨
Note: If the Autorun screen doesn’t appear automatically, or if you get a blank white screen or a white screen shows up (your computer doesn’t have Adobe Flash Player installed), go to Start, Run, and type D:\Utility\Setup.exe (where D is the letter of your CD drive) and click OK. Windows Vista users: At this point, you may get a warning message like the one below. Make sure that you click Allow to continue with the installation. 5
ページ6に含まれる内容の要旨
Step 4 Click Next at the welcome screen. Step 5 Click Next to accept the default destination folder. 6
ページ7に含まれる内容の要旨
Step 6 Click Continue Anyway at the Windows Logo Screen. (For Windows 2000, click Yes at the Digital Signature Not Found prompt). 7
ページ8に含まれる内容の要旨
For Windows Vista, click the Install this driver software anyway button when the security warning appears. Step 7 Click Yes, I want to restart my computer now and then Finish to restart your computer. 8
ページ9に含まれる内容の要旨
Step 8 After the computer is restarted, Windows will ask to connect to Windows Update, select No, not this time and click Next. If this screen does not appear, you can skip to section 2.2. Step 9 Select Install the software automatically and click Next. 9
ページ10に含まれる内容の要旨
Step 10 Click Continue Anyway at the Windows Logo Screen. (For Windows 2000, click Yes at the Digital Signature Not Found prompt). 10
ページ11に含まれる内容の要旨
For Windows Vista, click the Install this driver software anyway button when the security warning appears. Step 11 Click Finish. 11
ページ12に含まれる内容の要旨
3. Configuring the Adapter This section describes how to connect your wireless adapter to a wireless network. Note to Windows XP Users: You must disable the Wireless Zero Configuration Utility in order to use the bundled Wireless Utility. Please follow the steps below to disable XP’s wireless utility. Windows Vista users can skip the following instructions and go to Step 1 Double-click on the Wireless Network Connection Icon in the system tray and then click on Properties or A
ページ13に含まれる内容の要旨
Step 1 To open the utility, double click on the Wireless Monitor icon in the system tray at the bottom right-hand corner of your screen. Step 2 Go to the AP List tab, select the SSID (Network Name) of the wireless network you wish to connect to, and click Connect. 13
ページ14に含まれる内容の要旨
If the network you are attempting to connect to is configured for encryption, you will see an orange lock icon next to the network. 14
ページ15に含まれる内容の要旨
When you click on it and click connect, a box will pop up requesting the wireless encryption key for the router. Enter the encryption key into the box and click OK. 15
ページ16に含まれる内容の要旨
Step 3 You should now be connected. You should see “Connected” in the top, right hand corner, and there will be a blue circle around the antenna icon next to the network name. Troubleshooting: If you are experiencing problems with the connection (unable to connect, low signal strength, slow connection speed, not working, unstable wireless connection) you will want to tune your router’s signal by changing channels on the router. You do not need to change the channel on the card,
ページ17に含まれる内容の要旨
restart the wireless computer before trying to connect again. Keep going through the channels until you find one that gives you a stable connection. For instructions on changing channels, refer to the documentation that came with your router. 17
ページ18に含まれる内容の要旨
4. Wireless Monitor This section describes the various functions of the Wireless Monitor that you can configure, including the settings of wireless encryption. 4.1 Wireless Information The Wireless Information box at the top of the window provides you with the status of the current connection, including signal, network name (SSID), IP Address and router channel. 18
ページ19に含まれる内容の要旨
4.2 AP List The AP List tab displays all the available wireless networks detected by the Wireless Adapter. Simply select the wireless network you wish to connect to and click Connect. If you have created multiple profiles, you can use the profile chooser at the bottom to select the specific profile you want to use. Then click Activate to enable that profile. 19
ページ20に含まれる内容の要旨
4.3 Profile Settings This section provides instructions on using the Profile Settings section of the wireless monitor. The My Wireless Networks box lists the different profiles you’ve created for the different networks that you use. Profiles are automatically created and added to this list when you connect to new networks. You can also manually add profiles. To modify an existing profile, select that profile from the My Wireless Networks box and click on modify. To create a n