ページ1に含まれる内容の要旨
MIMO XR™ 802.11g Cardbus Adapter
Model # AWLC5025
User’s Manual
Ver. 1A
ページ2に含まれる内容の要旨
Table of Contents 1. Introduction................................................................................................................................. 3 1.1 Package Contents.................................................................................................................. 3 2. Installation................................................................................................................................... 4 2.1 Install Driver & Utility...............
ページ3に含まれる内容の要旨
1. Introduction Thank you for purchasing the MIMO XR™ Cardbus Adapter. When used with other Airlink101™ MIMO XR™ wireless products, the wireless signal range extends farther than standard 802.11g products. This Adapter supports 64/128-bit WEP data encryption that protects your wireless network from eavesdropping. It also supports WPA (Wi-Fi Protected Access) feature that combines IEEE 802.1x and TKIP (Temporal Key Integrity Protocol) technologies. Client users are required to authoriz
ページ4に含まれる内容の要旨
2. Installation 2.1 Install Driver & Utility This section provides instructions on how to install the MIMO XR™ Cardbus Adapter. The driver is installed along with the utility. Note: Do not insert the Cardbus Adapter until you have reached the appointed step. For Windows 98SE and ME users, you may be prompted to insert the Windows 98SE or ME CD during the driver installation. Be sure to have your Windows 98SE or ME CD ready. Step 1 Insert the Driver & Utility CD into your CD dri
ページ5に含まれる内容の要旨
Step 2 Click Next at the welcome screen. Step 3 Click Next to accept the default destination folder. 5
ページ6に含まれる内容の要旨
Step 4 Click Continue Anyway at the Windows Logo Screen. (For Windows 2000, click Yes at the Digital Signature Not Found prompt). Step 5 Verify Yes, I want to restart my computer now is selected and click Finish to restart your computer. 6
ページ7に含まれる内容の要旨
Step 6 After your computer is restarted, insert the Cardbus Adapter. Step 7 Select Install the software automatically and click Next. For Windows 98SE and ME, select Search for the best driver for your device and click Next. Verify all the check boxes are checked and click Next. 7
ページ8に含まれる内容の要旨
Step 8 Click Continue Anyway at the Windows Logo Screen. (For Windows 2000, click Yes at the Digital Signature Not Found prompt). Step 9 Click Finish. (Restart the computer for Windows 98SE and ME). 8
ページ9に含まれる内容の要旨
2.2 Verify Driver Installation To verify if the driver has been installed successfully, please perform the following steps. Step 1 Right-click on My Computer from your desktop and select Properties. Step 2 Select the Device Manager tab. (For Windows 2000/XP, select the Hardware tab first then click on Device Manager). 9
ページ10に含まれる内容の要旨
Step 3 Expand Network adapters from the list and verify that Airlink101 MIMO XR Cardbus Adapter is listed and no yellow question mark is beside it. If Airlink101 MIMO XR Cardbus Adapter is not listed, or you see a yellow question mark beside it, please re-install the driver again. 10
ページ11に含まれる内容の要旨
3. Configure the Cardbus Adapter This section describes how to connect your MIMO XR™ Cardbus Adapter to a wireless network. Note to Windows XP Users: You must disable the Wireless Zero Configuration Utility in order to use the bundled Wireless Utility. Please follow the steps below to disable XP’s wireless utility. Step 1 Double-click on the Wireless Network Connection Icon in the system tray and then click on Properties or Advanced. Step 2 Go to the Wireless Networks tab,
ページ12に含まれる内容の要旨
To open the Cardbus Adapter’s utility go to Start > (All) Programs > Airlink101 MIMO Cardbus Utility > Airlink101 MIMO Cardbus Utility. Step 1 Go to the AP List tab, select the SSID (Network Name) of the wireless network you wish to connect to, and click Connect. 12
ページ13に含まれる内容の要旨
Step 2 If encryption is not enabled for the selected access point / router, skip to step 6. Otherwise, enter a Profile Name for your wireless setting and click Next. Step 3 Verify that the Network Name matches the SSID of your wireless network and click Next. 13
ページ14に含まれる内容の要旨
Step 4 Select the proper encryption setting for your wireless router or access point from the drop-down menu and click Next. Step 5 Follow the on-screen instructions to complete the encryption settings. Click Complete when finished. Step 6 You should see a blue circle around the antenna icon indicating a valid connection. 14
ページ15に含まれる内容の要旨
Step 7 Go to the Link Information tab and click on the More button. Step 8 Verify that you are receiving adequate Signal Strength and Link Quality and that you have been assigned a valid IP address (instead of all 0’s). If you do not have adequate Signal Strength, try re-orienting the Access Point and/or the Cardbus Adapter to get a better reception. 15
ページ16に含まれる内容の要旨
4. Configure the Wireless Utility This section describes the various functions of the Wireless Utility that you can configure, including the settings of wireless encryption. 4.1 Link Information The Link Information tab shows the current profile in use as well as details of the current network connection. Click on the More button to see the details of the current network connection. 16
ページ17に含まれる内容の要旨
The Wireless Information displays the current wireless network you are connected to as well as various other statuses such as the Signal Strength and your assigned IP address. 17
ページ18に含まれる内容の要旨
4.2 AP List The AP List tab displays all the available Access Points detected by the Cardbus Adapter. Simply select the desired Access Point you wish to connect to and click Connect. The Site Information displays a list of status for the selected AP, including the Channel number and the Encryption status. 18
ページ19に含まれる内容の要旨
4.3 Configure Encryption Settings This section describes how to configure encryption settings for the Cardbus Adapter. Note: The encryption settings you set for the Adapter must match the same settings of the Access Point/Wireless Router; otherwise, the encryption will not work properly. Step 1 From the AP List tab, select the Access Point/Wireless Router you want to connect to and click Connect. Step 2 Verify the Profile Name is correct and click Next. 19
ページ20に含まれる内容の要旨
Step 3 Verify the Network Name (SSID) is correct and click Next. For WEP Settings: WEP Step 4 Select the appropriate Authentication Mode and Encryption settings and click Next. 20
