ページ1に含まれる内容の要旨
®
Megabit Modem
MM701G2 & MM702G2
User Manual
Product Catalog:
MM701G2 and MM702G2
Document Number: MM70xG2-UM-03
ページ2に含まれる内容の要旨
REVISION HISTORY The Revision History provides a summary of any changes in this manual. Please make sure you are using the latest revision of this manual. April 14, 2006 Revision Release Date Revisions Made 01 April 9, 2004 Initial release. 02 November 22, 2005 Minor changes to factory default restore procedure and rebranding. 03 April 14, 2006 Misc. Technical Updates. This manual is available online at ADC’s website (www.adc.com/documentationlibrary/) or you can order copies of the manual by c
ページ3に含まれる内容の要旨
Table of Contents About This Manual ........................................................................................................xiii Introduction ............................................................................................................................. xiii Organization ........................................................................................................................... 1-xiii Intended Audience .................................................
ページ4に含まれる内容の要旨
Table of Contents April 14, 2006 Change Spanning Tree Setting .............................................................................................. 5-10 Saving Changes ..................................................................................................................... 5-12 Rebooting the Modem ............................................................................................................5-14 Chapter 6: Configuring DSL Parameters .............................
ページ5に含まれる内容の要旨
April 14, 2006 Table of Contents Manage WAN Sessions ...........................................................................................................A-8 Add a New Session ............................................................................................................A-9 Set Up an RFC 1483 Bridged Session ............................................................................A-10 Set Up an RFC 1483 Routed Session ........................................................
ページ6に含まれる内容の要旨
Table of Contents April 14, 2006 vi MM70xG2-UM-03
ページ7に含まれる内容の要旨
List of Figures Figure 1-1. Remove the Modem ......................................................................................... 1-1 Figure 1-2. Set the MDI/MDI-X Switch ................................................................................ 1-3 Figure 1-3. Rear Panel Connections .................................................................................. 1-4 Figure 1-4. Reboot the Modem with the Reset Button ....................................................... 1-6 Figure
ページ8に含まれる内容の要旨
List of Figures April 14, 2006 Figure 5-14.Reboot ............................................................................................................ 5-14 Figure 6-1. DSL Quick Configuration .................................................................................. 6-1 Figure 6-2. G.SHDSL Advanced Configuration ................................................................... 6-3 Figure 7-1. G.SHDSL Advanced Configuration—Configure for Central-Office Mode ......... 7-2 Figure
ページ9に含まれる内容の要旨
April 14, 2006 List of Figures Figure A-7. WAN Session Management .............................................................................A-8 Figure A-8. Create New Session .........................................................................................A-9 Figure A-9. RFC 1433 Routed Session ............................................................................. A-11 Figure A-10.PPPoA Routed Session .............................................................................
ページ10に含まれる内容の要旨
List of Figures April 14, 2006 x MM70xG2-UM-03
ページ11に含まれる内容の要旨
List of Tables Table 1-1. Required Equipment ........................................................................................... 1-2 Table 1-2. LED Status Indicators .......................................................................................... 1-5 Table 5-1. User Access Levels ............................................................................................. 5-2 Table B-1.DSL Port (RJ-11) (2-Wire) ...................................................................
ページ12に含まれる内容の要旨
List of Tables April 14, 2006 xii MM70xG2-UM-03
ページ13に含まれる内容の要旨
ABOUT THIS MANUAL INTRODUCTION ® ® This manual applies to the ADC Megabit Modem versions MM701G2 and MM702G2. These modems can be used in two types of applications: • as an endpoint (CPE) to a DSLAM for Internet and other broadband connection through a service provider • as a LAN extension by implementing a point-to-point connection with another modem of the same model (MM701G2 to MM701G2 or MM702G2 to MM702G2) ORGANIZATION To complete an endpoint installation for an MM701G2 or MM702G2 modem, fo
ページ14に含まれる内容の要旨
About This Manual April 14, 2006 Reader Alert Meaning Alerts you to possible equipment damage from electrostatic discharge ATTENTION Alerts you to possible data loss, service-affecting procedures, or other similar type CAUTION problems Alerts you that failure to take or avoid a specific action might result in hardware damage or WARNING loss of service Alerts you that failure to take or avoid a specific action might result in personal harm DANGER INSPECTING YOUR SHIPMENT Upon receipt of the equ
ページ15に含まれる内容の要旨
LINK TX RX COL PWR SYNC TX RX MAR 1 Chapter INSTALLATION OVERVIEW The MM701G2 and MM702G2 are versatile, high-speed modems that connect an Ethernet LAN to one or more service providers using G.shdsl transmission technology. The connections provide instant and high-speed broadband access to the Internet or to other types of Wide Area Networks (WANs). The MM701G2 and MM702G2 provide the following: • Configuration either as a point-to-point LAN extension or as an end-connection to a DSLAM (see “
ページ16に含まれる内容の要旨
Chapter 1: Installation April 14, 2006 DETERMINE WHAT YOU NEED In addition to what is shipped with the modem, you need the following hardware and software to complete the installation and configuration. Table 1-1. Required Equipment Equipment: Requirement: PC Hardware: Ethernet NIC Card (10 Mbps) installed in each PC and other network equipment that will be connected to the LAN. Verify if the NIC in the device which directly connects to the modem LAN port is half- or full-duplex. The modem LA
ページ17に含まれる内容の要旨
April 14, 2006 Chapter 1: Installation CONNECT CABLES Install cables for the Ethernet port (see “Connect the 10/100Base-T Port” below). Then check “LED Status Indications” on page 1-5. Connect the 10/100Base-T Port Set the modem MDI/MDI-X switch for the 10/100Base-T port to allow the modem to connect directly to other network devices such as a PC, hub, switch, or router. Step Action 1 Set the modem MDI/MDI-X switch (see Figure 1-2) to one of the following: • MDI-X when connecting to a device s
ページ18に含まれる内容の要旨
Chapter 1: Installation April 14, 2006 Step Action 2 Connect the cables to the modem rear panel as shown below in Figure 1-3: • Silver cable to the DSL line port and wall jack • Black Ethernet cable to the 10/100Base-T port and to another Ethernet device such as a PC, hub, or router • Power cable to the modem power connector and to facility power Figure 1-3. Rear Panel Connections 3 Refer to “LED Status Indications” on page 1-5 to verify modem status via LEDs. 1-4 MM70xG2-UM-03
ページ19に含まれる内容の要旨
April 14, 2006 Chapter 1: Installation LED STATUS INDICATIONS The following table summarizes the modem’s operational status as provided by the front panel LEDs. Table 1-2. LED Status Indicators LED State Description PWR On green Modem has power. Off Modem does not have power. LAN LINK On green A PC, hub, or other network device is connected to the modem 10/100Base-T interface. Off No device is connected to the modem 10/100Base-T interface. TX Flashing green Modem is transmitting data to device
ページ20に含まれる内容の要旨
Chapter 1: Installation April 14, 2006 REBOOTING THE MODEM WITH THE RESET BUTTON The reset button on the back panel of your modem is provided to reboot the modem without the need to remove power. Under normal circumstances, you will not have to use the reset button. On rare occasions, however, your modem may not respond. In this case, you need to perform a reset to get your modem running properly again (see “Rebooting the Modem” on page 5-14 for information about rebooting the modem from the
