ページ1に含まれる内容の要旨
CardBus 10/100 Fast
Ethernet PC Card
Quick Installation Guide
ページ2に含まれる内容の要旨
HARDWARE INSTALLATION 1. Hold the CardBus PC Card with wide connector toward the slot and the brand label facing upward. 2. Insert the CardBus PC Card and push it firmly into the bottom. (Please see the following figure for reference) Notebook 3. Connect the RJ-45 port of the CardBus 10/100 Ethernet PC Card Adapter to a Category 5 Network cable before loading any network driver. For operation in the 100Mbps (100Base-TX) Ethernet network, a Category 5 unshielded twisted pair
ページ3に含まれる内容の要旨
SOFTWARE INSTALLATION Windows 95 Installation (OSR2 or later) 1. Boot up computer to Windows 95. Make sure the CardBus 10/100 Fast Ethernet PC Card is well connected to the CardBus Socket. 2. Click Next in the Update Device Driver Wizard Windows. 3. Click Others Locations to select a driver manually. 4. Insert the installation disk into the floppy disk drive and type A:\ (Assumed A:\) to specify the location of the installation driver. The driver will be installed automatically.
ページ4に含まれる内容の要旨
Windows 98 Installation 1. Boot up computer to Windows 98. Make sure the CardBus 10/100 Fast Ethernet PC Card is well connected to the CardBus Socket. 2. The system will automatically detect the card and ask for the device driver. Click Next to continue. 3. Select Search for the best driver for your device(Recommended) and click Next to continue. - 3 -
ページ5に含まれる内容の要旨
4. Insert the installation disk into the floppy disk drive and select Floppy disk drives. Click Next to start the search. 5. Click Next to continue when the suitable driver for the device selected. 6. Insert the original Windows 98 CD/disks to reset the system as requested. Click OK to continue. - 4 -
ページ6に含まれる内容の要旨
7. Follow on-screen instruction. Click Finish to complete the installation. 8. Click Yes to restart the system to activate the card. Windows 2000 Installation 1. When the CardBus 10/100 Fast Ethernet PC Card is well connected to the CardBus Socket, the system will detect automatically the card and ask for the necessary device driver. Click Next to continue. 2. Select Search for a suitable driver for my device (recommended) and click Next. - 5 -
ページ7に含まれる内容の要旨
3. Insert the installation disk into the floppy disk drive and select Floppy disk drives and click Next to start the search. 4. Click Next to continue when the appropriate driver for the device is selected. 5. Click Yes in the Digital Signature Not Found window to continue. - 6 -
ページ8に含まれる内容の要旨
6. Follow on-screen instruction to complete installation. 7. Click Finish when the installation done. Window ME Installation 1. Boot up computer to Windows ME. Make sure the CardBus 10/100 Fast Ethernet PC Card is well connected to the CardBus Socket. 2. The system will automatically detect the card and ask for the device driver. Select Automatic search for a better driver (Recommended) and click Next to continue. - 7 -
ページ9に含まれる内容の要旨
3. Insert the installation disk into the disk drive and select Removable Media (Floppy, CD-ROM…) and click Next. 4. Click Next to continue when the appropriate driver for the device is selected. 5. Follow on-screen instruction to complete installation. 6. Click Finish when the installation done. Windows XP Installation 1. Windows will detect automatically the new device which being well connected and prompt you to insert the network device - 8 -
ページ10に含まれる内容の要旨
driver. Click Install from a list or specific location… and click next to continue. 2. Insert the installation disk into the floppy disk driver. Select Search for the removable media(floppy, CD-ROM…) and click Next to proceed. 3. Windows will start searching for the appropriate driver for the installation. When the screen instruction appears as below, click Continue Anyway to proceed. - 9 -
ページ11に含まれる内容の要旨
4. Click Finish when the installation done. - 10 -
