ページ1に含まれる内容の要旨
802.11 b/g/n
Mini Wireless LAN
USB 2.0 Adapter
User’s Manual
ページ2に含まれる内容の要旨
Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio commun
ページ3に含まれる内容の要旨
Table of Contents CHAPTER 1: INTRODUCTION .....................................................1 FEATURES ..............................................................................................1 CHAPTER 2: INSTALLATION.......................................................1 FOR WINDOWS 2000/XP .........................................................2 INSTALL THE SOFTWARE..........................................................................2 INSTALL THE HARDWARE ................
ページ4に含まれる内容の要旨
Statistics...........................................................................................................................34 About ................................................................................................................................35 FOR WINDOWS VISTA...........................................................36 STATION MODE.....................................................................................37 Profile ..................................
ページ5に含まれる内容の要旨
Chapter 1: Introduction The WU5214 (Wireless LAN USB Adapter) is an IEEE802.11b/g/n USB adapter that connects your notebook to a wireless local area network. The WU5214 fully complies with IEEE 802.11n draft 3.0 and IEEE 802.11 b/g standards, delivers reliable, cost-effective, feature rich wireless connectivity at high throughput from an extended distance. The WU5214 is a very small adapter that can connect notebook, handheld or desktop computer equipped with USB interface for wireless
ページ6に含まれる内容の要旨
Installation For Windows 2000/XP Install the Software Note: Do not insert the Wireless LAN USB Adapter into the computer until the InstallShield Wizard finished installing. 1. Exit all Windows programs. Insert the included Installation CD into the computer. The CD-ROM will run automatically. 2. When the License Agreement screen appears, please read the contents and select “I accept the terms of the license agreement “ then click Next to continue. 3. Select the check box to c
ページ7に含まれる内容の要旨
Microsoft Zero Configuration Tool: Choose to use Windows XP’s built-in Zero Configuration Utility (ZCU). Click Next to continue. 5. When prompt to the following message, please click Install to begin the installation. 6. When the following screen appears, click Finish to complete the software installation. - 3 -
ページ8に含まれる内容の要旨
Install the Hardware Note: Insert the Wireless LAN USB Adapter when finished software installation. Insert the Wireless LAN USB Adapter into the USB Port of the computer. The system will automatically detect the new hardware. - 4 -
ページ9に含まれる内容の要旨
Verification To verify if the device is active in the computer. Go to Start > Setting > Control Panel > System > Hardware > Device Manager. Expand the Network Adapters category. If the 802.11n/b/g Mini Wireless LAN USB2.0 Adapter is listed here, it means that the device is properly installed and enabled. - 5 -
ページ10に含まれる内容の要旨
For Windows Vista Install the Software Note: Do not insert the Wireless LAN USB Adapter into the computer until the InstallShield Wizard finished installing. 1. Exit all Windows programs. Insert the included Installation CD into the computer. The CD-ROM will run automatically. 2. When the License Agreement screen appears, please read the contents and select “I accept the terms of the license agreement “ then click Next to continue. - 6 -
ページ11に含まれる内容の要旨
3. When prompt to the following message, please click Install to begin the installation. 4. When the following screen appears, click Finish to complete the software installation. - 7 -
ページ12に含まれる内容の要旨
Install the Hardware Note: Insert the Wireless LAN USB Adapter when finished software installation. Insert the Wireless LAN USB Adapter into the USB Port of the computer. The system will automatically detect the new hardware. Verification To verify if the device is active in the computer. Go to Start > Setting > Control Panel > System > Hardware > Device Manager. Expand the Network Adapters category. If the 802.11n/b/g Mini Wireless LAN USB2.0 Adapter is listed here, it means
ページ13に含まれる内容の要旨
Network Connection IP Address Note: When assigning IP address(es) to computers on the network, remember to have IP address for each computer set on the same subnet mask. If the Broadband Router has been enabled DHCP server function, it won’t be necessary to assign static IP address for PC. 1. To configure a dynamic IP address (i.e. if the broadband Router is enabled the DHCP server), check the Obtain an IP address automatically option. 2. To configure a fixed IP address (if DHCP se
ページ14に含まれる内容の要旨
Chapter 3: Utility Configuration For Windows 2000/XP After the Wireless LAN USB Adapter has been successfully installed, users can use the included Configuration Utility to set the preference. Go to Start (All) Program Intelligent Wireless Intelligent Wireless Utility. Users can also open the Configuration Utility by double clicking or right clicking the icon in the tray to select Launch Config Utility. - 10 -
ページ15に含まれる内容の要旨
Station Mode IMPORTANT NOTICE: Under screen resolution 800 x 600 pixels, if users click the triangle button at the right down corner of the utility windows to expand the station linking information that will NOT be displayed completely. Profile Profile can let users book keeping the favorite wireless setting among home, office, and other public hot-spot. Users may save multiple profiles, and activate the correct one at preference. The Profile manager enables users to Add, Edit, Dele
ページ16に含まれる内容の要旨
Encryption Shows the encryption type. Use 802.1x Whether or not use 802.1x feature. Transmit power, the amount of power used by a radio transceiver to send Tx Power the signal out. Channel Shows the selected channel that is currently in use. Choose from CAM (Constantly Awake Mode) or PSM (Power Saving Power Save Mode Mode.) RTS Threshold Shows the RTS Threshold of the device. Fragment Threshold Shows the Fragment Threshold of the device. Add Click to add a profile from the drop-do
ページ17に含まれる内容の要旨
• The Ad-hoc lets users set a small wireless workgroup easily and quickly. Equipped with the Wireless LAN USB Adapter, users can share files and printers between each PC and laptop. Tx Power: Transmit power, the amount of power used by a radio transceiver to send the signal out. Select the Tx power percentage from the pull-down list including Auto, 100%, 75%, 50%, 25%, 10% and Lowest. Preamble: This function will show up when Ad-hoc network type be selected. A preamble is a signal used
ページ18に含まれる内容の要旨
• Shared: Shared key is when both the sender and the recipient share a secret key. • LEAP: Light Extensible Authentication Protocol. It is an EAP authentication type used primarily in Cisco Aironet WLANs. It encrypts data transmissions using dynamically generated WEP keys, and supports mutual authentication (only with CCX mode enabled.) • WPA/ WPA-PSK/ WPA2/ WPA2-PSK: WPA or WPA-PSK authentications offer two encryption methods, TKIP and AES. For WPA-PSK, select the type of algorithm T
ページ19に含まれる内容の要旨
EAP Method: • PEAP: Protect Extensible Authentication Protocol. PEAP transport securely authentication data by using tunnelling between PEAP clients and an authentication server. PEAP can authenticate wireless LAN clients using only server-side certificates, thus simplifying the implementation and administration of a secure wireless LAN. • TLS / Smart Card: Transport Layer Security. Provides for certificate-based and mutual authentication of the client and the network. It relies on cli
ページ20に含まれる内容の要旨
ID/ PASSWORD: Identity and password for server. • Authentication ID / Password: Identity, password and domain name for server. Only "EAP-FAST" EAP method and "LEAP" authentication can key in domain name. Domain name can be keyed in blank space. • Tunnel ID / Password: Identity and Password for server. Show Password: Check this box to show the passwords that have been entered. OK: Click to save settings and exit this page. Cancel: Click to call off the settings and exit. Client Certif
