ページ1に含まれる内容の要旨
HP NC522SFP Dual Port 10 GbE Server
Adapter
User Guide
Part Number 537709-001
March 2009 (First Edition)
ページ2に含まれる内容の要旨
© Copyright 2009 Hewlett-Packard Development Company, L.P. The information contained herein is subject to change withoutice t no . The only warranties for HP products and services are set forth in the express warranty statements accompanying such produc ts and services. Nothing herein should be construed as constituting an additional w arranty. HP shall not be liable for technical or editorial errors or omissions contained herein. Intended audience This document is for the person who instal
ページ3に含まれる内容の要旨
Contents Technician notes...........................................................................................................................4 Warnings, cautions, and notes....................................................................................................................4 Downloading files.....................................................................................................................................5 HP contact information.......................
ページ4に含まれる内容の要旨
Technician notes Warnings, cautions, and notes WARNING: Only authorized technicians trained by HP should attempt to repair this equipment. All troubleshooting and repair procedures are detailed to allow only subassembly/module-level repair. Because of th e complexity of the in dividual boards and subassemblies, no one should attempt to make repairs at the component level or to make modifications to any printed wiring board. Im proper repairs can create a safety hazard. WARNI
ページ5に含まれる内容の要旨
NOTE: Any indications of component replacement or printed wiring bo ard modifications may void any warranty. Downloading files 1. Go to the HP website ( http://www.hp.com/#Support). 2. Select Download drivers and software (and firmware) . 3. Type the adapter name in the For product box and then click Go . For example, type NC522SFP. 4. Download the drivers, firmware, or documentation as needed. HP contact information For the name of the nearest HP au thorized reseller: • See
ページ6に含まれる内容の要旨
Introduction Overview The HP NC522SFP Dual Port 10 GbE Server Adapter is a dual port PCI Express (PCIe) 10 Gigabit ProLiant Ethernet adapter. The network connecn is m tio ade through two 10GBASE-SFP+ modules. In addition to standard HP network server adapter features, the NC522SFP is capable of supporting teaming for load balancing and failover, TCP checksum and segmentation (LSO) offload capability, VLAN tagging, jumbo frames, IPv6, and other features. Th NC522S e FP can be installed in
ページ7に含まれる内容の要旨
LED indicator Status Description On (Green) Link to the adapter is established. The adapter is receiving power and the cable connection is good. HP Direct Attach copper cables, fiber optic ca and ble, SFP+ module part numbers are listed in the following tables. Direct attach Part number copper cable (0.5 - 10 m) HP 0.5 m SFP+ 487649-B21 10 GbE Copper Cable HP 1 m SFP+ 487652-B21 10 GbE Copper Cable HP 3 m SFP+ 487655-B21 10 GbE Copper Cable HP 7 m SFP+ 487658-B21
ページ8に含まれる内容の要旨
HP 2 m LC-LC AJ835A Multi-Mode OM3 Fiber Optic Cable HP 5 m LC-LC AJ836A Multi-Mode OM3 Fiber Optic Cable HP 15 m LC-LC AJ837A Multi-Mode OM3 Fiber Optic Cable HP 30 m LC-LC AJ838A Multi-Mode OM3 Fiber Optic Cable HP 50 m LC-LC AJ839A Multi-Mode OM3 Fiber Optic Cable SFP+ module Part number HP BladeSystem 455883-B21 10Gb SR SFP+ HP BladeSystem 455886-B21 10Gb LR SFP+ HP BladeSystem 455889-B21 10Gb LRM SFP+ Introduction 8
ページ9に含まれる内容の要旨
Installing an adapter Installation overview This section describes installation precautions, how to install the adapter, and how to connect the network cable. WARNING: To reduce the risk of personal inju or da ry mage to the equipment, consult the safety information and user documentation prov ided with the server before attempting the installation. Many servers are capable of providing energy le vels that are considered hazardous and are intended to be serviced only by qualified
ページ10に含まれる内容の要旨
Installing an adapter in a server See the HP ProLiant server documeation for additional information on ho nt w to safely install a PCI Express card in the server. CAUTION: If the server is not PCI Hot Plug comp liant, power it down and unplug the power cord from the power outlet before removing th e server access panel. Failure to do so may damage the adapter or server. 1. Power down the server. 2. Remove the power cord and server access panel. T en remove the h cover bracket
ページ11に含まれる内容の要旨
2. Using a correctly sized Phillips head screwdriver, carefully remove the two board lock screws located at the top and bottom of the connector. 3. Remove the standard profile bracket and place the lo w profile bracket over the connector. Be careful not to damage the connector or bend the low profile bracket. 4. Reinstall the two Phillips screws. 5. Orient the SFP modules with the label side down an d then reinstall the modules all the way into their sockets until they click into place a
ページ12に含まれる内容の要旨
Specifications Cable specifications SFP+ modules or Fiber type Cable grade Minimum modal Operating range copper cable bandwidth @ 850 (meters) nm (MHz-km) 10GBASE-SR 62.5 μm MMF FDDI 160 2 to 26 (short range) 62.5 μm MMF OM1 200 2 to 33 50 μm MMF OM2 500 2 to 82 50 μm MMF OM3 2000 2 to 300 10GBASE-LRM 50, 62.5 μm MMF OM1, OM2, OM3 N/A 0.5 to 220 (long reach multimode) 10GBASE-LR 10 μm SMF B1.1, B1.3 SMF N/A 2 to 10,000 (long range) Direct attached Twin Axial Copper @26 AWG N
ページ13に含まれる内容の要旨
Compliance Standard Other PCIe v2.0 RoHS 6 of 6 IPv4, IPv6 CE ACPI 1.1a Microsoft WHQL (Windows Hardware Quality Labs) Server Design Guide version 3.0 (SDG 3.0) Power and environmental specifications Power and Value environmental specifications Operating Temperature 32° to 131° F (0° to 55° C ) Humidity 10% to 90% Non-operating Temperature -85° to 185° F (-65° to 85° C) Humidity 5% to 95% Power 2.03A @ 12 V and 570 mA @ 3.3
ページ14に含まれる内容の要旨
Regulatory compliance notices Regulatory compliance identification numbers For the purpose of regulatory compliance certification and identification, this s product has been assigned a unique regulatory model number. The regulatory mo del number can be found on the product nameplate label, along with all required approval markings and information. When requesting compliance information for this product, always refer to this re gulatory model number. The re gulatory model number is not th
ページ15に含まれる内容の要旨
Canadian notice This Class A digital apparatus meets all requirements of the Canadian Interf erence-Causing Equipment Regulations. Cet appareil numérique de la classe A respecte tou es les exigenc t es du Rèement su gl r le matériel brouilleur du Canada. Korean class A notice Japanese class A notice Disposal of waste equipment by users in private households in the European Union This symbol on the product or on its packaging in dicates that this produc t must not be dispos
ページ16に含まれる内容の要旨
Electrostatic discharge Preventing electrostatic discharge To prevent damaging the system, be aware of the precautions you need to follow when setting up the system or handling parts. A discharg e of static electricity from a fer or other con ing ductor may damage system boards or other statics- ensitive devices. Thitype of damage may redu s ce the life expectancy of the device. To prevent electrostatic damage: • Avoid hand contact by transporting and st oring products in static-safe co
ページ17に含まれる内容の要旨
Acronyms and abbreviations CSA Canadian Standards Association DMA direct memory access IEEE Institute of Electrical and Electronics Engineers iSCSI Internet Small Computer System Interface PCI Express Peripheral Component Interconnect Express RDMA Remote Direct Memory Access RSS Receive-Side Scaling SFP small form-factor pluggable TOE TCP/IP Offload Engine Acronyms and abbreviations 17
ページ18に含まれる内容の要旨
Index A S adapter LEDs 6 specifications 12, 13 adapters 6 standards 14 B T bracket, low profile 10 technical notes 4 C V cables, networking 11 ventilation 4 compliance 12, 14 contact information 5 W warnings 4 D disposal, waste 15 downloading files 5 E electrostatic discharge 9, 16 environmental specifications 13 F features 6 G grounding methods 16 L LC connector 11 LEDs 6 low profile bracket 10 P PCI (peripheral component in
