ページ1に含まれる内容の要旨
ページ2に含まれる内容の要旨
Throughout this guide, blocks of text may be accompanied by an icon and printed in bold type or in italic type. These blocks are notes, notices, cautions, and warnings, and they are used as follows: NOTE: A NOTE indicates important information that helps you make better use of your computer system.
ページ3に含まれる内容の要旨
(Rev. 11/3/98) FILE LOCATION: S:\SYSTEMS\SlimFast\ts\ProcUpgrade\028WD\028WDet0toc.fm Precautionary Measures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1 Before You Begin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2 Recording the System Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2 Updating the ESM Firmware . . . . . . . . . . . . . . . . . . .
ページ4に含まれる内容の要旨
(Rev. 11/3/98) FILE LOCATION: S:\SYSTEMS\SlimFast\ts\ProcUpgrade\028WD\028WDet0toc.fm Figure 1-5. Removing the SEC Cartridge and Heat Sink From the PowerEdge 2450. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-10 Figure 1-6. Installing the SEC Cartridge and Heat Sink Into the PowerEdge 2450. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-11 Figure 1-7. Removing a Terminator Card. . . . . . . . . . . . . . . . . . . . . . . . . . .
ページ5に含まれる内容の要旨
(Rev. 11/3/98) FILE LOCATION: S:\SYSTEMS\SlimFast\ts\ProcUpgrade\028WD\028wdeb0.fm
! "# This document provides information on upgrading and installing microprocessors in Dell PowerEdge 2400, 2450, and 4400 systems.
Before you perform any of the procedures in this document, take a few moments to read the following warning for your personal safety and to prevent damage to the sys- tem
ページ6に含まれる内容の要旨
(Rev. 11/3/98) FILE LOCATION: S:\SYSTEMS\SlimFast\ts\ProcUpgrade\028WD\028wdeb0.fm In addition, take note of these safety guidelines when appropriate: When you disconnect a cable, pull on its connector or on its strain-relief loop, not on the cable itself. Some cables have a connector with locking tabs; if you are disconnecting this type of cable, press in on the locking tabs before disconnecting the cable. As you pull connectors apart, keep them evenly aligned to avoid bending any connec
ページ7に含まれる内容の要旨
(Rev. 11/3/98) FILE LOCATION: S:\SYSTEMS\SlimFast\ts\ProcUpgrade\028WD\028wdeb0.fm
If an ESM firmware diskette is included with the upgrade kit, update your ESM firm- ware with the version contained on that diskette by performing the following steps. The latest version of the ESM firmware is available at http://support.dell.com. 1. Insert the ESM firmware diskette into the diskette drive. 2. Reboot the system. 3. After the system completes the boot routine, follow the
ページ8に含まれる内容の要旨
(Rev. 11/3/98) FILE LOCATION: S:\SYSTEMS\SlimFast\ts\ProcUpgrade\028WD\028wdeb0.fm
This section provides instructions for: Removing the cooling shroud, single-edge contact (SEC) cartridge, and heat sink Installing the new SEC cartridge and heat sink and replacing the cooling shroud Reassembling and checking the system "
#
$
% '
:)
ページ9に含まれる内容の要旨
(Rev. 11/3/98) FILE LOCATION: S:\SYSTEMS\SlimFast\ts\ProcUpgrade\028WD\028wdeb0.fm thumbscrew retention pins (2)
4. Remove the SEC cartridge and heat sink as follows. $ *
="=
= *
=
0 <
ページ10に含まれる内容の要旨
(Rev. 11/3/98) FILE LOCATION: S:\SYSTEMS\SlimFast\ts\ProcUpgrade\028WD\028wdeb0.fm heat sink SEC cartridge tab (2) guide-bracket assembly
##
$
%
#
#
0
ページ11に含まれる内容の要旨
(Rev. 11/3/98) FILE LOCATION: S:\SYSTEMS\SlimFast\ts\ProcUpgrade\028WD\028wdeb0.fm heat sink SEC cartridge tab (2) guide-bracket assembly !
&#
%
1. Replace the right-side system cover and front bezel, reconnect your computer and peripherals to their power sources, and turn them on. As the system boots, it detects the presence of the new microprocessor and automatically changes the s
ページ12に含まれる内容の要旨
(Rev. 11/3/98) FILE LOCATION: S:\SYSTEMS\SlimFast\ts\ProcUpgrade\028WD\028wdeb0.fm NOTE: If a setup password has been assigned by someone else, contact your network administrator for information on resetting the chassis intrusion detector. 3. Run the Dell Diagnostics to verify that the new microprocessor is operating correctly. See your User’s Guide and your Installation and Troubleshooting Guide for additional information on running the Dell Diagnostics and troubleshooting any problems th
ページ13に含まれる内容の要旨
(Rev. 11/3/98) FILE LOCATION: S:\SYSTEMS\SlimFast\ts\ProcUpgrade\028WD\028wdeb0.fm air blower power supply tab enclosure slot air blower power cable
"#
4. Remove the SEC cartridge and heat sink as follows. *
=
0 1 <
$ *
="=
ページ14に含まれる内容の要旨
(Rev. 11/3/98) FILE LOCATION: S:\SYSTEMS\SlimFast\ts\ProcUpgrade\028WD\028wdeb0.fm heat sink SEC cartridge tab guide-bracket assembly $
$ DELL CONFIDENTIAL - Preliminary 9/11/00 1-10 Microprocessor Upgrade Installation Guide
ページ15に含まれる内容の要旨
(Rev. 11/3/98) FILE LOCATION: S:\SYSTEMS\SlimFast\ts\ProcUpgrade\028WD\028wdeb0.fm
##
$
%
0
"
233/-! 1. Slide the SEC cartridge and
ページ16に含まれる内容の要旨
(Rev. 11/3/98) FILE LOCATION: S:\SYSTEMS\SlimFast\ts\ProcUpgrade\028WD\028wdeb0.fm
Each microprocessor is contained within an SEC cartridge and heat sink assembly. The system board has two guide-bracket assemblies, which hold the SEC cartridge and heat sink assemblies. If your system has only one microprocessor, the secondary guide-bracket assembly must contain a terminator card. If you add a se
ページ17に含まれる内容の要旨
(Rev. 11/3/98) FILE LOCATION: S:\SYSTEMS\SlimFast\ts\ProcUpgrade\028WD\028wdeb0.fm terminator card retention clips (2) latches (2) guide-bracket assembly &
'
DELL CONFIDENTIAL - Preliminary 9/11/00 support.dell.com Microprocessor Upgrade Installation Guide 1-13
ページ18に含まれる内容の要旨
(Rev. 11/3/98) FILE LOCATION: S:\SYSTEMS\SlimFast\ts\ProcUpgrade\028WD\028wdeb0.fm 5. Pivot the retention clips away from the guide-bracket assembly. 6. Slide the terminator card out of the guide-bracket assembly.
##
'
To install a terminator card in the guide-bracket assembly, perform the following steps: 1. Slide the terminator card into the guide-bracket assembly until the edge connec- tor on the terminator card is firmly seated in the connector on the system board. 2
ページ19に含まれる内容の要旨
(Rev. 11/3/98) FILE LOCATION: S:\SYSTEMS\SlimFast\ts\ProcUpgrade\028WD\028wdeb0.fm #
$
%(&# To install the replacement SEC cartridge and heat sink assembly, perform the follow- ing steps: 1. Remove the terminator card or old SEC cartridge from the guide bracket assembly. 2. Slide the SEC cartridge and heat sink assembly into the guide-bracket assembly until the edge connector on the SEC cartridge is firmly seated in the connector on the system board
ページ20に含まれる内容の要旨
(Rev. 11/3/98) FILE LOCATION: S:\SYSTEMS\SlimFast\ts\ProcUpgrade\028WD\028wdeb0.fm DELL CONFIDENTIAL - Preliminary 9/11/00 1-16 Microprocessor Upgrade Installation Guide
