ページ1に含まれる内容の要旨
MG10_E.book Page 1 Monday, May 26, 2003 1:52 PM
MIXING CONSOLE
Owner’s Manual
Making the Most Of Your Mixer
Pages 6 to 16
E
ページ2に含まれる内容の要旨
MG10_E.book Page 2 Monday, May 26, 2003 1:52 PM Precautions —For safe operation— WARNING If lightning begins to occur, turn off the power switch of the unit Installation as soon as possible, and unplug the power plug from the electri- cal outlet. Connect this unit’s AC power adaptor only to an AC outlet of the If there is a possibility of lightning, do not touch the power plug type stated in this Owner’s Manual or as marked on the unit. if
ページ3に含まれる内容の要旨
MG10_E.book Page 3 Monday, May 26, 2003 1:52 PM Precautions —For correct operation — Connector pin assignments Interference from Cell Phones XLR-type connectors are wired as follows Use of a mobile phone near this unit may induce noise. If noise Pin 1: ground; Pin 2: hot (+); Pin 3: cold (–). occurs, move the phone further from the unit. INSERT TRS phone jacks are wired as follows Sleeve: ground; Tip: send; Ring: return. Replacement of Consumable Parts The perfo
ページ4に含まれる内容の要旨
MG10_E.book Page 4 Monday, May 26, 2003 1:52 PM Introduction Thank you for your purchase of the YAMAHA MG10/2 mixing console. This mixing console combines ease of operation with support for multiple usage environments. Please read through this Owner’s Manual carefully before beginning use, so that you will be able to take full advantage of this mixer’s superlative features and enjoy trouble-free operation for years to come. Features Contents The MG10/2 provid
ページ5に含まれる内容の要旨
MG10_E.book Page 5 Monday, May 26, 2003 1:52 PM Introduction Before Turning on the Mixer Turning the Power On (1) Be sure that the mixer’s power switch is in the STANDBY Press the mixer’s power switch to the ON position. When you are position. ready to turn the power off, press the power switch to the STANDBY position. Use only the PA-10 adaptor included with this mixer. Use of a different adaptor may result in equipment Note that trace current continues to flow while the
ページ6に含まれる内容の要旨
MG10_E.book Page 6 Monday, May 26, 2003 1:52 PM Making the Most Of Your Mixer An Introduction You’ve got yourself a mixer and now you’re ready to use it. Just plug everything in, twiddle the controls, and away you go … right? Well, if you’ve done this before you won’t have any problems, but if this is the first time you’ve ever used a mixer you might want to read through this little tutorial and pick up a few basics that will help you get better performance and make better mixes. MG
ページ7に含まれる内容の要旨
MG10_E.book Page 7 Monday, May 26, 2003 1:52 PM Making the Most Of Your Mixer A Place For Everything and Everything In Its Place 1 1-1. A Plethora Of Connectors—What Goes Where? Questions you’re likely to encounter when setting up a system for the first time might include “Why all these different types of connectors on the back of my mixer?” and “What’s the difference?”. Let’s start by taking a look at the most common connector types. The Venerable RCA Pin Jack This is the “co
ページ8に含まれる内容の要旨
MG10_E.book Page 8 Monday, May 26, 2003 1:52 PM Making the Most Of Your Mixer 1-2. Balanced, Unbalanced—What’s the Difference? In a word: “noise.” The whole point of balanced lines is noise rejection, and it’s something they’re very good at. Any length of wire will act as an antenna to pick up the random electromagnetic radiation we’re constantly surrounded by: radio and TV signals as well as spurious electromagnetic noise generated by power lines, motors, electric appliances,
ページ9に含まれる内容の要旨
MG10_E.book Page 9 Monday, May 26, 2003 1:52 PM Making the Most Of Your Mixer 1-3. Signal Levels—Decibel Do’s and Don’ts From the moment you start dealing with things audio, you’ll have to deal with the term “decibel” and its abbreviation, “dB”. Things can get confusing because decibels are a very versatile unit of measure used to describe acoustic sound pressure levels as well as electronic signal levels. To make matters worse there are a number of variations: dBu, dBV, dB
ページ10に含まれる内容の要旨
MG10_E.book Page 10 Monday, May 26, 2003 1:52 PM Making the Most Of Your Mixer Where Your Signal Goes Once It’s Inside the Box 2 At first glance the block diagram of even a modest mixer can look like a space-station schematic. In reality, block diagrams are a great aid in understanding how the signal flows in any mixer. Here’s a greatly simplified block diagram of a generic mixer to help you become familiar with the way these things work. 2-1. Greatly Simplified Mixer
ページ11に含まれる内容の要旨
MG10_E.book Page 11 Monday, May 26, 2003 1:52 PM Making the Most Of Your Mixer The First Steps in Achieving Great Sound 3 Before you even consider EQ and effects, or even the overall mix, it is important to make sure that levels are properly set for each individual source. This can’t be stressed enough—initial level setup is vitally important for achieving optimum performance from your mixer! Here’s why … and how. 3-1. The Head Amplifier “Gain” Control Is the Key! Let’s review our s
ページ12に含まれる内容の要旨
MG10_E.book Page 12 Monday, May 26, 2003 1:52 PM Making the Most Of Your Mixer 3-2. Level Setup Procedure For Optimum Performance Now that we know what we have to do, how do we do it? If you take another quick look at the mixer block diagram you’ll notice that there’s a peak indicator located right after the head amplifier and EQ stages, and therein lays our answer! Although the exact procedure you use will depend on the type of mixer you use and the application, as well as your persona
ページ13に含まれる内容の要旨
MG10_E.book Page 13 Monday, May 26, 2003 1:52 PM Making the Most Of Your Mixer External Effects and Monitor Mixes 4 Pre/Post—What’s the difference? 4-1. AUX Buses For Monitor Sends and Overall Effects pre post There are a number of reasons why you might A “pre-fader” signal is taken A “post-fader” signal is want to “tap” the signal flowing through your from a point before the taken from a point after the channel fader, so the send channel fader, so its level mixer at some point before the ma
ページ14に含まれる内容の要旨
MG10_E.book Page 14 Monday, May 26, 2003 1:52 PM Making the Most Of Your Mixer 4-2. Channel Inserts for Channel-specific Processing Another way to get the mixer’s signal outside the box is to use the channel inserts. The channel inserts are almost always located before the channel fader and, when used, actually “break” the mixer’s internal sig- nal path. Unlike the AUX sends and returns, the channel insert only applies to the corresponding chan- nel. Channel inserts are most commonly used for
ページ15に含まれる内容の要旨
MG10_E.book Page 15 Monday, May 26, 2003 1:52 PM Making the Most Of Your Mixer Making Better Mixes 5 Music First—Then Mix 5-1. Approaching the Mix—Where Do You Start? In any case, the music comes first. Think about the music and let it guide the mix, rather than try- Mixing is easy, right? Just twiddle the faders ing to do things the other way around. What is the around until it sounds right? Well, you can do it music saying and what instrument or technique is that way, but a more systematic
ページ16に含まれる内容の要旨
MG10_E.book Page 16 Monday, May 26, 2003 1:52 PM Making the Most Of Your Mixer One of the biggest problems with too much boost Spread them Out! is that it adds gain to the signal, increasing noise Position your instruments so they have room to and potentially overloading the subsequent cir- “breathe,” and connect in the most musical way cuitry. with other instruments. Sometimes, however, you’ll want to deliberately pan sounds close together, or even right on top of one another, to 5-4. Ambien
ページ17に含まれる内容の要旨
MG10_E.book Page 17 Monday, May 26, 2003 1:52 PM Front & Rear Panels 4 Equalizer (HIGH, MID, and LOW) Channel Control Section This three-band equalizer adjusts the channel’s high, mid, and low frequency bands. Setting the knob to the position pro- duces a flat frequency response. Turning the knob to the right boosts the corresponding frequency band, while turning to the Channels Channels Channels left attenuates the band. The following table shows the EQ 1 and 2 3/4 and 5/6 7/8 and 9/10 typ
ページ18に含まれる内容の要旨
MG10.fm Page 18 Thursday, December 11, 2003 9:23 AM Front & Rear Panels 2 RETURN Control Master Control Section Adjusts the level of the signal sent from the RETURN jacks (L (MONO) and R) to the Stereo bus. If you supply a signal to the RETURN L (MONO) NOTE jack only, the mixer outputs the identical signal to both the L and R Stereo buses. 3 2TR IN Control Adjusts the level of the signal sent from the 2TR IN jack to the Stereo bus. 4 ST Master Fader 7 Adjusts the s
ページ19に含まれる内容の要旨
Front & Rear Panels Input/Output Section 1 3 4 5 6 7 2 9 8 0 1 Channel Input Jacks (CHs 1, 2, 3/4, 5/6) 3 Channel Input Jacks (CHs 7/8, 9/10) • MIC jacks Each of these channel pairs can be used to input a stereo source These are balanced XLR-type input jacks (1:Ground; 2:Hot; signal. For each pair, the odd-numbered channel inputs the L 3:Cold). signal, and the even-numbered channel inputs the R signal. • LINE jacks Each channel offers a choice of two jack types: phone jack and These are bal
ページ20に含まれる内容の要旨
Front & Rear Panels These jacks can also be used as an auxiliary stereo 8 SEND Jacks NOTE input. If you connect to the L(MONO) jack only, the • AUX1, AUX2 mixer will recognize the signal as monaural and will These are impedance balanced phone-type output jacks. propagate the identical signal on both L and R These jacks output the signals from AUX1 and AUX2, jacks. respectively. You use these jacks, for example, to connect to an effector or monitor system. 0 PHONES Jack Connector for headphones.
