ページ1に含まれる内容の要旨
DIGITAL PIANO
DP100
OWNER'S MANUAL
ページ2に含まれる内容の要旨
Thank you for choosing this Kawai DP100 Digital Piano. Your new DP100 is a high-quality instrument offering the very latest in leading-edge music technology. This manual contains valuable information that will help you make full use of your piano’s many capabilities. Please read it carefully and keep it handy for further reference. TABLE OF CONTENTS Page Important Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Assembling The Stand . . . . . . . . . . .
ページ3に含まれる内容の要旨
Important Safety Instructions SAVE THESE INSTRUCTIONS INSTRUCTIONS PERTAINING TO A RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS WARNING TO REDUCE THE RISK OF CAUTION FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE RISK OF ELECTRIC SHOCK THIS PRODUCT TO RAIN DO NOT OPEN OR MOISTURE. AVIS : RISQUE DE CHOC ELECTRIQUE - NE PAS OUVRIR. TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The lighting f
ページ4に含まれる内容の要旨
Do not lean against the keyboard. Doing so may cause the product to fall over, resulting in injury. Do not disassemble, repair or modify Doing so may result in product breakdown, electric the product. shock or short-circuit. When disconnecting the AC power cord' s Pulling the AC power cord itself may damage the cord, causing a fire, electric shock or plug, always hold the plug short-circuit. and pull it to remove it. The product is not completely disconnected from the Failure to do so
ページ5に含まれる内容の要旨
Doing so may result in discoloration or deformation Do not wipe the product with benzene of the product. or thinner. When cleaning the product, put a soft cloth in lukewarm water, squeeze it well, then wipe the product. Doing so may cause the product to become Do not stand on the product or exert deformed or fall over, resulting in breakdown excessive force. or injury. The product should be located so that its location or position does not interfere with its proper ventilation. This
ページ6に含まれる内容の要旨
ASSEMBLING THE STAND Be sure that all parts are included before starting to assemble your unit. PARTS PROVIDED Side Panel (A) . . . . . . . . 2 pcs. Back Panel (B) . . . . . . . 1 pc. Pedal Board (C) . . . . . . 1 pc. Screw (D) . . . . . . . . . . . 2 pcs. Screw (E) . . . . . . . . . . . 4 pcs. Bolt (F) . . . . . . . . . . . . . 8 pcs. Adjuster (G) . . . . . . . . . 1 pc. Cord Clamp (H) . . . . . . 1 pc. (D) (E) (F) (H) 1. Insert the Adjuster (G) on the bottom of Bottom View (F) (G) Pedal Board
ページ7に含まれる内容の要旨
3. Place the piano on the front half of the stand so that the metal fitting holes are seen when viewed from the top. Slide the piano backward while holding it with one hand so that it does not incline and fall from the stand. The (F) Hand or Finger hooks on the piano are then engaged catching hazard with the metal fittings on the Side Panels. Pay attention so that your hand or fingers are not caught between the stand and piano. Fasten the piano and the stand with four bolts (F). CAUTION: Be s
ページ8に含まれる内容の要旨
PART NAMES VOLUME SLIDER (A) Move the volume slider to the right to increase the instrument’s volume. Move the slider to the left to decrease the volume. DEMO BUTTON (B) To listen to all the demos, simply press this button. The piano will start the demo. Seven musical pieces will be played back randomly until the DEMO button is pressed again to stop. To select a specific demo, press the desired TONE button while the demo is playing. To stop the demo, press this button again. TONE BUTTON (C)
ページ9に含まれる内容の要旨
SOFT PEDAL (H) Pressing this pedal softens the sound and also reduces its volume. * The soft pedal can be used as the sostenuto pedal by turning on the power while depressing this pedal. H I SOSTENUTO PEDAL Depressing this pedal after pressing the keyboard and before releasing the keys sustains the sound of only the keys just played. SUSTAIN PEDAL (I) Pressing this pedal sustains the sound even after you remove your hands from the keyboard. LINE IN/OUT JACKS (J) Connect an external amplifer and
ページ10に含まれる内容の要旨
GETTING STARTED 1. BASIC OPERATIONS (1) Turn on the power. (2) Adjust the volume. Play a note on the keyboard and adjust the volume (Moving the slider to the right raises the volume while moving to the left lowers it.) (3) Choose a tone. Pressing a TONE button automatically changes the sound made by the piano. The LED above the selected tone button will light to indicate which tone is currently in being used. (4) Play. Experiment by playing the different tones. (5) Dual With DUAL mode you can l
ページ11に含まれる内容の要旨
2. TRANSPOSE KEY (1) Press the TRANSPOSE button and the LED above C D E F G A B it will be lit. The LED above the current key button (TONE button) will also be lit. If the key of “C” is selected the TRANSPOSE button will not light. (When power is first turned “on”, the key is set to C.) When any key other than “C” is selected the TRANSPOSE E-flat LED will light. (2) While holding down the TRANSPOSE button, press the key button (TONE button) for the key you woul
ページ12に含まれる内容の要旨
DIGITAL RECORDING FUNCTIONS 1. RECORDING A SONG (1) Press the REC button. The piano will be ready for recording. To cancel the recording, press the REC button again. (2) Begin playing some music on the piano. The piano will automatically start recording with the first note you play. You can also start recording by pressing the PLAY/STOP button. (3) Press the PLAY/STOP button when you have finished recording. NOTE: Starting another recording will delete the song you previously recorded. METRON
ページ13に含まれる内容の要旨
3. DELETING A SONG This function allows you to delete song that were not recorded correctly or song that you do not want to listen to any more. (1) Simultaneously hold down the PLAY/STOP and REC buttons. (2) Releasing all the buttons will delete the song NOTE: – The total memory capacity of the recorder is approximately 1,800 notes. When the recorder reaches its maximum capacity, the piano will stop recording at this point. Any data recorded before the interruption will be retained. – The reco
ページ14に含まれる内容の要旨
PROGRAMMING MODE The Programming Mode gives you access to many other useful features on your piano. To use the Programming Mode functions, press a key on the keyboard while holding down the TOUCH and TRANSPOSE buttons. To exit the Programming Mode, release the TOUCH and TRANSPOSE buttons. The following functions can be selected in the Programming Mode: SELECTING A TOUCH TYPE (C or D or E key) TUNING (C-sharp or E-flat key) MIDI CHANNEL SELECT (F or G or A key) TRANSMIT MIDI PROGRAM CHANGE ON/O
ページ15に含まれる内容の要旨
(1) To select the “LIGHT”, “CONSTANT” or “HEAVY” Touch Type, press one of the following keys on the keyboard while holding down the TOUCH and TRANSPOSE buttons. Any C key: Selects the “LIGHT” Touch Type Any D key: Selects the “HEAVY” Touch Type Any E key: Selects the “CONSTANT” Touch Type (2) Release both hands after selecting the Touch Type to exit the programming mode. When the TOUCH LED is off, the “NORMAL” Touch Type is automatically selected. When an alternative touch type is selected usin
ページ16に含まれる内容の要旨
4. TRANSMIT MIDI PROGRAM CHANGE ON/OFF You can use 7 tone buttons to transmit Program Change Numbers via MIDI. Please refer to the list below for assignment of tone and program number. TONE NAME PRG # PRG # (When Multi-Timbral mode is ON) CLASSIC GRAND 1 1 MODERN PIANO 2 2 E.PIANO 3 5 CHURCH ORGAN 4 20 HARPSICHORD 5 7 VIBRAPHONE 6 12 STRINGS 7 49 (1) If you press any B-flat key while holding down the TOUCH and TRANSPOSE buttons, this function is set to “off” and the piano does not transmi
ページ17に含まれる内容の要旨
6. MIDI LOCAL CONTROL ON/OFF This function is used to control whether or not the sound from the piano will be heard when you play the keyboard. When MIDI LOCAL CONTROL is set to on you will hear the piano when you play. When MIDI LOCAL CONTROL is set to off you will not hear any sound from the piano when you play but the piano's keyboard data will be transmitted through the MIDI jacks to an external MIDI device. (1) If you press any F-sharp key while holding down the TOUCH and TRANSPOSE button
ページ18に含まれる内容の要旨
MIDI The term MIDI is an acronym for Musical Instrument Digital Interface, an international standard for connecting synthesizers, sequencers (digital recorders) and other electronic instruments so that they can exchange performance data. The DP100 is equipped with two MIDI jacks for exchanging data: MIDI IN and MIDI OUT. Each uses a special cable with a DIN connector. MIDI IN : For receiving note, program change and other data. MIDI OUT : For sending note, program change and other data. MIDI E
ページ19に含まれる内容の要旨
(2) Connection to an external sequencer When connected as shown in the illustration, you can record song played on the DP100 with a sequencer, and use the DP100’s tones (such as piano, harpsichord and vibraphone, etc.) controlled by the DP100’s MULTI-TIMBRAL MODE function to create a multi-layer MIDI recording. DP100 OUT IN MIDI OUT MIDI MIDI IN MIDI cable MIDI sequencer – 19 –
ページ20に含まれる内容の要旨
SPECIFICATIONS Keyboard 88 Weighted Keys with Hammer Mechanism Touch Type 4 Types (Normal, Light, Heavy, Constant) Max Polyphony 32 Notes Tones 7 Tones (CLASSIC GRAND, MODERN PIANO, E.PIANO, CHURCH ORGAN, HARPSICHORD, VIBRAPHONE, STRINGS ) Effects Reverb (Room, Stage, Hall) Digital Recorder 1-Song, 1,800-Note Other Functions Transpose, Tuning, MIDI Functions, 7 Demo Songs Pedals 2 (Soft or Sostenuto, Sustain) Jacks Headphones x 2, Pedal, MIDI IN/OUT, LINE IN/OUT (L, R) Speakers 12 cm x 2 (4 3/4
