Fishman SBT-Cの取扱説明書

デバイスFishman SBT-Cの取扱説明書

デバイス: Fishman SBT-C
カテゴリ: 楽器用ペダル
メーカー: Fishman
サイズ: 0.17 MB
追加した日付: 5/19/2014
ページ数: 12
説明書を印刷

ダウンロード

使い方は?

私たちの目的は、皆様方にデバイスFishman SBT-Cの取扱説明書に含まれたコンテンツを可能な限り早く提供することです。オンラインプレビューを使用すると、Fishman SBT-Cに関してあなたが抱えている問題に対する解決策の内容が素早く表示されます。

便宜上

説明書Fishman SBT-Cをこちらのサイトで閲覧するのに不都合がある場合は、2つの解決策があります:

  • フルスクリーン表示 – 説明書を(お使いのコンピュータにダウンロードすることなく)便利に表示させるには、フルスクリーン表示モードをご使用ください。説明書Fishman SBT-Cのフルスクリーン表示を起動するには、全画面表示ボタンを押してください。
  • コンピュータにダウンロード - Fishman SBT-Cの説明書をお使いのコンピュータにダウンロードし、ご自身のコレクションに加えることもできます。デバイス上のスペースを無駄にしたくない場合は、いつでもManualsBaseサイトでダウンロードすることもできます。
Fishman SBT-C 取扱説明書 - Online PDF
Advertisement
« Page 1 of 12 »
Advertisement
印刷版

多くの人々は画面表示ではなく印刷された説明書を読むほうを好みます。説明書を印刷するオプションも提供されており、上記のリンクをクリックすることによりそれを利用できます - 説明書を印刷。説明書Fishman SBT-Cを全部印刷する必要はなく、選択したページだけを印刷できます。紙を節約しましょう。

要旨

次のページにある説明書Fishman SBT-Cの内容のプレビューは、以下にあります。次のページにある説明書の内容をすぐに表示したい場合は、こちらをご利用ください。

内容要旨
ページ1に含まれる内容の要旨

USER GUIDE
SBT

ページ2に含まれる内容の要旨

Read Me First! Installation of this product is a straightforward procedure, but we recommend this job only if you are an experienced repair technician. Plugging In An impedance matching preamp is recommended, but not required. This will help realize the full frequency response potential of the pickup and allow for cable runs longer than 10 feet without signal deterioration. Use a high quality, low capacitance ¼” shielded instrument cable (models SBT-HP and SBT-E) or the provided cable (SBT-

ページ3に含まれる内容の要旨

Installing the Model SBT-C Parts 1 � SBT-C Pickup with ⁄ ” Shielded Jack 8 � (3) Double-sided Adhesive Pads � Adhesive-backed Jack Holder � Felt-covered Strain Relief Clip � 10’ Instrument Cable 1.5” 1.5” 3

ページ4に含まれる内容の要旨

Preparation The model SBT-C may be mounted onto a classical guitar, a steel string guitar, a dulcimer and similar stringed instruments. The installation may be performed either on the outside of the instrument or inside the soundhole where the transducer will be out of harm’s way. In instruments with small soundholes (dulcimers, for example), internal installation may not be practical. As a general rule, the transducer should be mounted over a freely vibrating location and STRAIN not over a

ページ5に含まれる内容の要旨

below the highest pitched string noting the position where these two measure- ments meet. This will serve as a test location. 2. Apply an adhesive pad to the shiny brass face of the transducer and mount at the location indicated in step 1. The transducer wire should follow the grain of the soundboard and point toward the soundhole of the instrument. Check the location by plugging in the pickup and listening. Should the position prove unsatisfactory, move the pickup in ¼” increments and re-tes

ページ6に含まれる内容の要旨

adjacent to the soundhole. 5. Insert the jack into the jack holder and plug the instrument cable into the jack. 6. Attach the felt-covered strain relief clip to the soundhole. Note: The felt-covered clip can be bent to accommodate different soundhole thicknesses. 6

ページ7に含まれる内容の要旨

Installing the Model SBT-E Follow the same procedure as the Model SBT-C on page 3 to mount the pickup element. Parts: � SBT-E Pickup � ¼” Fishman Switchjack stereo endpin jack � (3) Double-sided Adhesive Pads 7

ページ8に含まれる内容の要旨

Install the pickup 1. Widen the endpin hole to 15/32” (11.9mm) to accommodate the endpin jack. For additional information, please refer to the Switchjack Installation Guide located at fi shman.com. 2. Solder the pickup “hot” wire to the Tip terminal, which is the shortest of the three tabs. Solder the pickup shield to the Ground tab on the jack. Gently tighten the strain relief. Switch (Long Terminal) Ring (Medium Terminal) Guitar Tip (Short Terminal) Shield 8

ページ9に含まれる内容の要旨

Installing the Model SBT-HP The Model SBT-HP is designed for harp or piano. Parts � SBT-HP with 42” Cord and ¼” Jack � (3) Double-sided Adhesive Pads � Adhesive-backed Jack Holder As a general rule, the transducer should be mounted over a freely vibrating location and not over a “dead” structural brace. The exact location for best results should be determined by experimentation. For harp mounting 1 1. The approximate pickup position will be between ⁄ and ½ the soundboard’s 3 length, starting a

ページ10に含まれる内容の要旨

2. Apply an adhesive pad to the shiny brass face of the transducer and mount outside the instrument, at the location indicated in step 1. The transducer wire should follow the grain of the soundboard and point toward the bottom of the instrument. 3. Plug the pickup into an amplifi er and experiment with the vertical location of the transducer. If you detect boominess or feedback, relocate the transducer higher up on the soundboard. In no case should it be necessary to mount it higher than ½

ページ11に含まれる内容の要旨

For piano mounting The SBT-HP should be mounted to the piano soundboard at a location adjacent to the higher strings. For example, on a grand piano the transducer should be placed directly on the soundboard within the third-largest ranges of the piano. For additional instructions, see the above information for harp mounting. 11

ページ12に含まれる内容の要旨

www.fi shman.com 009-030-001 Rev D 5-10


類似の説明書
# 取扱説明書 カテゴリ ダウンロード
1 Fishman Archtop Guitar Pickup 取扱説明書 楽器用ペダル 51
2 Fishman Aura Jerry Douglas Signature Series 取扱説明書 楽器用ペダル 7
3 Fishman 取扱説明書 楽器用ペダル 3
4 Sony FS-85B50 取扱説明書 楽器用ペダル 11
5 Sony HR GP5 取扱説明書 楽器用ペダル 126
6 Sony FS-85USB 取扱説明書 楽器用ペダル 3
7 Agilent Technologies 8648A 取扱説明書 楽器用ペダル 2
8 American DJ FSR-800 取扱説明書 楽器用ペダル 0
9 Antari Lighting and Effects Antari M-1 取扱説明書 楽器用ペダル 9
10 Aphex Systems 1401 取扱説明書 楽器用ペダル 5
11 Aphex Systems Foot Pedal 1404 取扱説明書 楽器用ペダル 0
12 Aphex Systems 1402 取扱説明書 楽器用ペダル 0
13 Aphex Systems 1403 取扱説明書 楽器用ペダル 11
14 BBE DI-1000 取扱説明書 楽器用ペダル 7
15 BBE 482i 取扱説明書 楽器用ペダル 73