ページ1に含まれる内容の要旨
FOODSER VICE
Owner’s Manual
Read And Save These Instructions
®
Blending Station MP
Maximum Performance
Commercial Blender
All Models
ページ2に含まれる内容の要旨
IMPORTANT SAFEGUARDS 1. Read all instructions. 2. To protect against risk of electrical shock, do not put motor base in water or other liquid. 3. Close adult supervision is necessary when appliance is used by or near children. ® 4. Unplug the power cord from the wall outlet when the Blending Station MP is not in use, before putting on or taking off parts and before cleaning other than washing the container. 5. Never contact moving parts. 6. Do not operate any appliance with a damaged cord or pl
ページ3に含まれる内容の要旨
13. Always operate with the lid in place. 14. WARNING: When processing hot liquids: • The two-part latching lid must be securely in place. This allows steam to escape naturally and will prevent the lid from coming off when the machine is turned on. • Use caution with hot liquids. Spraying from under the lid plug can occur or escaping steam may cause scalding. • Do not process hot liquids with the non-latching lid. 15. Display window area will scratch when contacted with a scouring pad or sharp
ページ4に含まれる内容の要旨
ontrol Panel C Display Window Speed Control Start/Stop AXIMUM ERFORMANCE M P Six Factory Pre-Set Owner Controls High/Low Pulse Programs ® Blending Station MP ON/OFF switch - Located on the side of the Motor Base, the ON/OFF switch controls the power to the machine. With the machine plugged in, switch the machine to ON to ready the machine for blending. START/STOP button - Pressing START/STOP once starts and runs the machine and turns the blades. Press the START/STOP button again to stop the mac
ページ5に含まれる内容の要旨
DISPLAY WINDOW - This area, depending on what button is pressed, displays a variety of operation messages. A “READY” message appears when there is power to the machine. OWNER CONTROLS - A control panel accessible by pressing the Vita-Mix logo. • Press once to reveal the mode message. Press button READY 1 then 6 within five seconds to continue. Once the correct code is entered the display will indicate the motor temperature (NORM, WARM, HOT), a usage count and a total. The “COUNT” is a machine
ページ6に含まれる内容の要旨
ustom Programming C ® The Blending Station MP is packaged with an MP smoothie programming chip. Please keep the chip in a safe, easily accessible spot and always keep it in the original package. This chip is used to program your machine with the six smoothie programs optimized for the MP48 container. Although your machine comes from the factory pre-set with the MP programs, follow these instructions, when using the supplied programming chip, in the event your machines PRE-SET buttons were alte
ページ7に含まれる内容の要旨
4. Insert the custom programmed chip with the words, “THIS SIDE FACING TO THE FRONT OF THE MACHINE” toward you and the silver contact bars up, into the slot. The DISPLAY WINDOW will read “NEW MODULE.” 5. Within 10 seconds the six PRE-SET buttons will be re-programmed and the DISPLAY WINDOW will read “SAVED” then “READY.” If nothing happens when the programming chip is fully inserted, turn the chip in the opposite direction and try again. 6. Remove the programming chip and return it to the o
ページ8に含まれる内容の要旨
id Assembly L ® NOTE: Outside the United States and Canada, your Blending Station MP may come with a different container configuration. Two-Part Lid 48 oz. (1.4 liter) Maximum Performance Container The two-part lid is easy to clean and easy to put on, take off and seal. • To remove a fully latched lid, lift the two tabs and pull upward and off. • Twist the center lid plug to fasten or remove. NOTE: The Maximum Performance Container will not ® work on older Vita-Mix machines. If the container F
ページ9に含まれる内容の要旨
Tamper Back Cover: 1. To remove the Back Cover from the Blending Station: a. First remove the Cover Door from the unit, as described above. b. Remove the two (2) Back Cover mounting screws located on the rear of the machine. (Figure D) c. From the rear of the machine, firmly push the bottom of the cover forward (towards the control panel), keeping the bottom edge of the cover against the motor base. DO NOT tilt or strike the cover during removal. d. Slide forward until the side latches on the f
ページ10に含まれる内容の要旨
n-Counter Installation I Preparing the counter area: • Before cutting holes, make sure that there is adequate clearance under the counter for the motor. The motor will extend about 5-2/3" (14.4 cm) below the counter but it is best to allow at least 10" (25.5 cm) from the under-counter to shelves or any other equipment under the counter. Also, when using the removable cover design, the back of the hole must be at least 6" (15.2 cm) from any wall to allow for cover door clearance. • An extra 6.5"
ページ11に含まれる内容の要旨
MAXIMUM PERFORMANCE All 120 VAC Blending Stations MP are built using a U.S. three-prong grounded cord and require a 20 amp outlet. • 220/240 VAC • 50/60 Hz • 1300-1550 Watts • 100 VAC (Japan) • 50/60 Hz • 1300 Watts Blending Station dimensions: • 17-1/2" (44.45 cm) high with lid closed • 21-1/2" (54.7 cm) high with lid open • Case depth: 12-3/4" (32.39 cm) with handle • Case width: 9-1/2" (24.13 cm) • Depth below counter: 5-2/3" (14.4 cm) • Recommended distance between machines: 12" (30.48 cm)
ページ12に含まれる内容の要旨
n-Counter Gasket I Gasket Installation Instructions: 1. Follow the instructions on page 10 on preparing the counter area for the ® installation of your In-Counter Blending Station MP. Also, use the Template Sheet (provided in your machine’s original package) to assist you in the placement and ventilation of your machine. 2. Lay the blender on its back with the motor pointing toward you. Allow 1-2 in. (3 -5 cm) of the motor base to hang over the edge of the counter top to facilitate easy fitti
ページ13に含まれる内容の要旨
lending Tips B 1. If your recipe freezes up, try reducing the amount of ice. Compared to other blenders, you do not need as much ice to make an equally frozen drink in a ® Blending Station MP. 2. Place liquids and soft foods in your container first. Hard items and ice should be placed last. 3. Whole, hard or frozen ingredients should be small. Solid frozen fruit is extremely difficult to blend. For best results, use semi-frozen fruit. Using same size batches of semi-frozen fruit and ice will ke
ページ14に含まれる内容の要旨
nstructions I ® How to operate your Blending Station MP using the six Pre-Set Programmed Buttons. The following is the basic MP settings of the six PRE-SET buttons (your machine’s PRE-SET buttons may differ due to program revisions or if your Blending Station MP was programmed specifically for your business). • Button 1: (:13) Blends thin drinks with just juice and ice. Button 1 will ramp the blending speed to medium high for 13 seconds. • Button 2: (:18) Blends light coffee drinks. Button 2 wil
ページ15に含まれる内容の要旨
4. Select desired programmed setting by pressing any of the PRE-SET BUTTONS 1 through 6. The machine will begin immediately to cycle through the selected program and turn off when the program is complete. Each button has a different pre-selected combination of speed and length for blending. NOTE: If you detect a change in the sound of the machine or if a hard or foreign object comes into contact with the blades, do not serve the drink. Inspect your blade assembly for loose, knicked or missing
ページ16に含まれる内容の要旨
nstructions I CONTINUED FROM PAGE 15 ® 1. Follow steps 1 through 3 of “How to operate your Blending Station MP using the Six Pre-Set Programmed Buttons” section on page 14. 2. The speed of the motor can be changed with: • the motor off. • the motor on. – Press the s or t buttons – With the container in place, press the until the desired speed START/STOP button. The machine percentage is displayed. will begin blending. 100% is the highest setting – While the machine is running, press and 7% is th
ページ17に含まれる内容の要旨
lade Agitator Assembly B Blade Agitator Assembly. The blade is sharp, use caution when handling. When inserting the blade assembly through the container bottom, grip the blades with a soft cloth, align the flat sides of the blade assembly with the flat sides of the container. Place the retainer nut back on 32 the inserted blade assembly and tighten clockwise. 24 Do not force. Do not attempt to disassemble blade 16 assembly. 8 4 Drive Spline. Mates with drive socket on the motor base to turn
ページ18に含まれる内容の要旨
arts List P Item# Part #15569 48 oz. (1.4 liter) - MP Container without lid assembly or blade assembly #15567 48 oz. (1.4 liter) - MP Container, blade assembly, no lid assembly #1159 48 oz. (1.4 liter) - Lid plug #15566 48 oz. (1.4 liter) - MP Container, blade assembly & lid assembly #15574 48 oz. (1.4 liter) - Two-part lid assembly #15575 48 oz. (1.4 liter) - Lid only (no plug) #15576 MP Container one-piece lid (lid plug not required) #18002 Back cover and cover door with removable hinge desi
ページ19に含まれる内容の要旨
#1159 #15574 #15575 #15603 #15569 #15566 OUNCES 48 40 32 24 #15567 16 8 #15598 4 #15576 #15585 #891 #15596 #15579 PGM121 #18003 #18005 #18004 #18002 19
ページ20に含まれる内容の要旨
are and Cleaning C Care Note To ensure that you get the longest possible life from your Vita-Mix product, we recommend the following products, when used as directed by the supplier: Cleaning Products Supplier Solid Supra, Solid Power, . . . . . . . . . . . .Ecolab, Inc., St. Paul, MN Guardian Acclaim, Solid Guardian Plus, 800-352-5326 Solid Super Impact, Solid Insure www.ecolab.com Diverpak . . . . . . . . . . . . . . . . . . . . . Diversey, Livonia, MI Eclipse
