ページ1に含まれる内容の要旨
MICRO COMPONENT SYSTEM
UX-J60— Consists of CA-UXJ60 and SP-UXJ60
UX-J50— Consists of CA-UXJ50 and SP-UXJ50
RM-SUXJ60R REMOTE CONTROL
SP-UXJ60 CA-UXJ60 SP-UXJ60
RM-SUXJ50R REMOTE CONTROL
SP-UXJ50 CA-UXJ50 SP-UXJ50
For Customer Use:
INSTRUCTIONS
Enter below the Model No. and Serial No.
which are located either on the rear, bot-
tom or side of the cabinet. Retain this
information for future reference.
Model No.
Serial No.
ページ2に含まれる内容の要旨
Warnings, Cautions and Others IMPORTANT FOR LASER PRODUCTS IMPORTANT for the U.K. DO NOT cut off the mains plug from this equipment. If the plug REPRODUCTION OF LABELS fitted is not suitable for the power points in your home or the cable 1 CLASSIFICATION LABEL ON EXTERIOR SURFACE is too short to reach a power point, then obtain an appropriate safety approved extension lead or consult your dealer. BE SURE to replace the fuse only with an identical approved type, as originally fitted. If nonethele
ページ3に含まれる内容の要旨
SAFETY INSTRUCTIONS “SOME DOS AND DON’TS ON THE SAFE USE OF EQUIPMENT” This equipment has been designed and manufactured to meet international safety standards, but like any electrical equipment, care must be taken if you are to obtain the best results and safety is to be assured. ✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮ Do read the operating instructions before you attempt to use the equipment. Do ensure that all electrical connections (including the mains plug, extension leads and inter
ページ4に含まれる内容の要旨
Introduction We would like to thank you for purchasing one of our JVC products. Before operating this unit, read this manual carefully and thoroughly to obtain the best possible performance from your unit, and retain this manual for future reference. Power sources About This Manual • When unplugging the unit from the wall outlet, always pull This manual is organized as follows: on the plug, not the AC power cord. • The manual mainly explains operations using the buttons on the remote control. DO
ページ5に含まれる内容の要旨
Contents Location of the Buttons and Control ..................................... 3 Front Panel ........................................................................................... 3 Remote Control .................................................................................... 5 Getting Started ........................................................................ 6 Supplied Accessories ............................................................................ 6 Putting the Batt
ページ6に含まれる内容の要旨
Location of the Buttons and Control Become familiar with the buttons and control on your unit. Front Panel Front Panel 1 FOR UX-J50: w 2 e 3 4 r 5 FOR UX-J50: t 6 7 y 8 u i 9 MICRO COMPONENT SYSTEM UX-J60 p q 3 EN01-15_UX-J60&50[B]f.pm6 3 02.12.23, 9:31 AM
ページ7に含まれる内容の要旨
Continued Display Window 12 3 45 [ ] [ ] DAILY REC SLEEP REC RDS TA News Info SURROUND BASS ST MONO PRGM RANDOM ALL AHB 67 8 9pq See the pages in parentheses for details. Front Panel Display Window 1 Disc tray 1 Timer indicators 2 Display window • (timer), DAILY, REC (recording timer), and SLEEP 3 REV.MODE (reverse mode) button (19 – 21) 2 REC (recording) indicator 4 AUX button (9) 3 RDS operation indicators Pressing this button also turns on the unit. • RDS and TA/News/Info 4 ONLY FOR UX-J60: 5
ページ8に含まれる内容の要旨
Remote Control See the pages in parentheses for details. 1 Number buttons 2 BASS button (10) 3 Multi operation buttons STANDBY/ON • UP, 4 (reverse skip), 7 (stop), ¢ (forward skip), and DOWN 1 2 3 9 4 SET button (17) DISPLAY 5 Source buttons 4 5 6 p 1 • CD 3/8, TAPE 2 3, FM/AM, and AUX CLOCK /TIMER Pressing one of these buttons also turns on the unit. 7 8 9 q 6 CD 0 (disc tray open/close) button (16) SLEEP 10 +10 w Pressing this button also turns on the unit. UP BASS TREBLE 7 REV.MODE (reverse m
ページ9に含まれる内容の要旨
Getting Started Continued Supplied Accessories Connecting Antennas Make sure that you have all the following items. FM antenna The number in parentheses indicates the quantity of each piece supplied. • AM loop antenna (1) FM antenna (supplied) • FM antenna (1) • Remote control (1) • Batteries (2) • Speaker cords (ONLY FOR UX-J60) (4) If anything is missing, consult your dealer immediately. Putting the Batteries into the Remote Control 1 Attach the FM antenna to the FM 75 Ω Insert the batteries—R
ページ10に含まれる内容の要旨
AM (MW) antenna Connecting Speakers 12 FOR UX-J60: 1 Vinyl-covered wire (not supplied) 23 3 Grey RIGHT RIGHT LEFT LEFT Red Speaker AM loop antenna cord Speaker MAIN SPEAKERS SUBWOOFERS (supplied) CAUTION: SPEAKER IMPEDANCE 6 -16 cord Black Blue 1 If the cords are covered with insulation, remove a short section of insulation at the end of each cord by twisting and pulling it off. 2 Connect the AM loop antenna to the AM LOOP terminals as illustrated. INPUT INPUT INPUT INPUT 3 Turn the AM loop
ページ11に含まれる内容の要旨
1 If the cords are covered with insulation, Connecting Other Equipment remove a short section of insulation at the To connect an audio equipment end of each cord by twisting and pulling it You can connect audio equipment—used only as a playback off. device. 2 Press and hold the clamp of the speaker • DO NOT connect any equipment while the power terminal as illustrated. is on. • DO NOT plug in any equipment until all 3 Insert the end of the speaker cord into the connections are complete. terminal
ページ12に含まれる内容の要旨
Common Operations To change the clock Setting the Clock 1 Make sure the (timer) indicator is not lit on the Before operating the unit any further, first set the unit’s clock. display. When you plug the AC power cord into the wall outlet, • If it is lit, press and hold CLOCK/TIMER until it goes “0:00” starts flashing on the display. off. You can set the clock whether the unit is on or off. 2 Press CLOCK/TIMER repeatedly until the unit enters • There is a time limit in doing the following steps.
ページ13に含まれる内容の要旨
Continued To reinforce the bass sound Adjusting the Volume You can reinforce the bass sound to maintain rich, full bass at You can adjust the volume level only while the unit is turned low volume—Active Hyper Bass Pro. on. The volume level can be adjusted between “VOL MIN” For UX-J60: and “VOLUME 1” – “VOLUME 40 (VOL MAX).” AHB Press AHB PRO. PRO On the remote control: • Each time you press the button, the Active Press VOLUME + to increase the volume or Hyper Bass Pro is turned on (AHB ON) and p
ページ14に含まれる内容の要旨
To enjoy the heavy sound (ONLY FOR UX-J60) Selecting the Display Color (ONLY FOR UX-J60) You can enjoy the heavy sound. The function boosts low and You can select the display color (COLOR 1 – COLOR 5 and high frequency sounds—Sound Turbo. AUTO mode). SOUND Press SOUND TURBO. TURBO • AUTO mode changes the color (COLOR 1 to COLOR 5) • Each time you press the button, the Sound gradually. Turbo is turned on and off alternately. When it COLOR To select the color, press COLOR. is turned on, the BASS i
ページ15に含まれる内容の要旨
Listening to FM and AM (MW) Broadcasts Continued Tuning in to a Station Presetting Stations You can preset 30 FM and 15 AM (MW) stations. FM/AM In some cases, test frequencies have been already memorized 1 Press FM/AM to select the band. for the tuner since the factory examined the tuner preset The unit automatically turns on and tunes in function before shipment. This is not a malfunction. to the previously received station—either FM You need to preset stations separately for the FM and AM or A
ページ16に含まれる内容の要旨
Tuning in to a Preset Station Receiving FM Stations with RDS On the remote control ONLY: RDS (Radio Data System) allows FM stations to send an additional signal along with their regular program signals. FM/AM 1 Press FM/AM to select the band. For example, the stations send their station names, as well as The unit automatically turns on and tunes in information about what type of program they broadcast, such to the previously received station—either FM as sports or music, etc. or AM (MW). When tu
ページ17に含まれる内容の要旨
Continued Changing the RDS Information Searching for Programs by PTY Codes (PTY Search) You can see RDS information on the display while listening to an FM station. One of the advantages of RDS is that you can locate a particular kind of program by specifying the PTY codes. On the remote control ONLY: • For details on the PTY codes, see “Additional Information” DISPLAY on page 25. Press DISPLAY (orange-colored). • Each time you press the button, the display To search for a program using the PTY
ページ18に含まれる内容の要旨
Switching Temporarily to a Program Type of How the Enhanced Other Networks function actually Your Choice works: The Enhanced Other Networks function allows the unit to switch temporarily to a broadcast program of your choice CASE 1 (TA, NEWS, and INFO) from a different station. If there is no station broadcasting the program you • The function only works when you are listening to a preset have selected FM RDS stations providing the data. The unit continues tuning in to the current station. « To
ページ19に含まれる内容の要旨
Playing Back Discs Continued This unit has been designed to play back the following discs Playing Back the Entire Disc—Normal Play —CD, CD-R, and CD-RW. CD When playing a CD-R or CD-RW 1 Press CD 0. User-edited CD-Rs (CD-Recordable) and CD-RWs The unit automatically turns on and the disc (CD-ReWritable) can be played only if they are already tray comes out. “finalized.” • Usually you can play back your original CD-Rs or CD- 2 Place a disc correctly on the circle of the RWs recorded in music CD f
ページ20に含まれる内容の要旨
PRGM Basic Disc Operations 2 Press PRGM (program). The PRGM (program) indicator lights up on While playing a disc, you can do the following operations. the display. To stop playing for a moment ST PRGM CD During play, press CD 3/8. While pausing, the elapsed playing time flashes on • If a program has been stored in memory, the program the display. is called up. To resume playing, press CD 3/8 again. UP 3 Press UP or DOWN to select the track number, then press SET. To go to another track • You ca
