ページ1に含まれる内容の要旨
Quiet Zone
Use And Care
Room Air Conditioner
Manual
Contents
Electrical Requirements ........................................ 2
Electrical Grounding Instructions.................................. 2
Safety Features ...................................................... 2
Compressor Lockout ..................................................... 2
Low Voltage Protection .................................................. 2
Advantages of Amana's Electronic Controls ....... 2
Operation ................
ページ2に含まれる内容の要旨
Electrical Requirements Safety Features This room air conditioner is equipped with an electronic Electrical Grounding Instructions control to improve comfort and ensure reliability. This appliance is equipped with a three-pro ng grounding plug fer protection against possible shock hazards. Ifatwe-prong Compressor Lockout wall receptacle is encountered, the customer is required to To extend the life of the compressor a three minute time contact a qualified electrician and have the two-prong wall
ページ3に含まれる内容の要旨
Operation Vent Control ENERGY SAVER mode provides the most ENERGY SAVER (HIGH, MED and LOW) - energy efficient use of your room air condi- tioner. In ENERGYSAVERmode, thefanstopswhenthe compressor stops cooling. This feature can be used with SMART COOL or cooling with any fan speed. Open or close the vent by sliding the vent control lever to the Amana's new air sampling system works to maintain set appropriate setting. temperature within 1.5°F while in ENERGY SAVER mode. Approximately every 5 mi
ページ4に含まれる内容の要旨
DELAY START OPERATION Note: Changes can be made only while display is flashing. You wilt have 5 seconds between each temperature, operating mode, and fan speed setection. If a setecdon is not made dudng this time frame, the unit will setect the default and proceed to the next step: Setting the delay time. If you wish to reset a missed selection, press the DELAY TIMER button and begin again. Procedure Button Display Indicator 1Turn the unit off. _FF _ '_1 Press the DELAY L, TIMER button. /i/ t Th
ページ5に含まれる内容の要旨
DELAY STOP OPERATION ** Procedure Button Display Indicator 1 With unit running, X\ / /ill//' press the DELAY BE_ 1 _//I iF Display flashes. TIMER button.* .\ \,/,/./ \\/,/i_ Change the delay time, if desired. V s_ /,/,i-\ /,/,i-\ Press the DELAY _,_TIMER button to start the time or select nothing and the unit will start automati- The display shows the countdown hours. cally. 70 cancel, press the DELAY TIMER or OFF button *A setting must be selected within a5-second tim e period, while flashing,
ページ6に含まれる内容の要旨
3. If using concentrated liquid detergent, dilute in warm water first. 4. Do not use abrasive cleaners such as Comet TM, Ajax TM, General Information etc. These items can scratch, crack, and discolor sur- faces. Changing Air Flow Direction Adjust horizontal baffles for directing air up or down Oceanside or Corrosive Environment Adjust vertical baffles with handle to direct air left or right Salt air or a corrosive environment maygreatly reduce the life of the unit. After cleaning, sand and repai
ページ7に含まれる内容の要旨
METHOD TWO: NOTE: A charcoal air purification filter accessory is avail- able that reduces smoke, odor, pollen, and fine dust par- ticles. See your store dealer for details or call Amana at 1- 1.Remove thefrontgrille. 800-843-0304. Slidethegrilletotheleftuntilitclearstheunitclipsand IMPORTANT NOTE: A dirty air filter reduces operating pullout, efficiency. Inspect filter at least once every week during operation. Clean filter with a vacuum cleaner or warm, 2.Graspthefilterhandleandslidethefiltert
ページ8に含まれる内容の要旨
Model Identification Any Questions? Complete enclosed registration card and promptly return Most of your questions can be answered by your local card to Amana's Product Registration department. If reg- Amana dealer. Check with your dealer first if you need any istration card is missing, call Amana's Consumer Informa- further information regarding the operation, maintenance, tion Line, (1-800-843-0304). or service of your unit. Then, if you should have any matters which are not resolved locally,
