ページ1に含まれる内容の要旨
3-228-220-12 (1)
CD Radio
Cassette-Corder
Operating Instructions
CFD-S40CP
©2001 by Sony Corporation
ページ2に含まれる内容の要旨
Information Warning For customers in the United States To prevent fire or shock hazard, This equipment has been tested and found to do not expose the player to rain comply with the limits for a Class B digital or moisture. device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordan
ページ3に含まれる内容の要旨
Basic Operations Table of contents Basic Operations Playing an audio CD or MP3 files .................. 4 Listening to the radio ...................................... 8 Playing a tape ............................................... 10 Recording on a tape ...................................... 12 The CD Player Using the display .......................................... 14 Locating a specific track ............................... 15 Scanning the beginning of the tracks (Intro Scan) .............
ページ4に含まれる内容の要旨
Basic Operations Playing an audio CD or MP3 files 3 1, 2 Connect the supplied AC power cord (see page 23). 1 Press Z PUSH OPEN/CLOSE down to open the CD compartment and place the CD on the CD PUSH OPEN/CLOSE compartment. With the label side up 2 Close the lid of the CD compartment. PUSH OPEN/CLOSE 3 Press u (N on the remote). Display CD The player turns on (direct power-on) and the player plays all the tracks once. To play a disc with MP3 files, see Track Playing page 6. number time 4
ページ5に含まれる内容の要旨
Basic Operations Use these buttons for additional operations POWER Z PUSH OPEN/CLOSE VOLUME +, – u Jog dial x Tip To Do this Playback starts from the adjust the volume Press VOLUME +, – track you last stopped (VOL +, – on the remote). playing (Resume play). During stop, the track stop playback Press x. number to be played are pause playback Press u (X on the remote). displayed. Press the button again to To cancel the resume play resume play after pause. to start play from the beginning of the fi
ページ6に含まれる内容の要旨
Playing an audio CD or MP3 files (continued) Playing a disc with MP3 files Z PUSH OPEN/CLOSE u Jog dial FOLDER/TRACK Note MP3 indicator Before playing a file, this player reads all file and M, m folder information on the disc. Depending on the 1 Press Z PUSH OPEN/CLOSE down to open the CD file structure, it may take compartment and place the CD on the CD compartment more than a minute to (see page 4) . read them. During this time, “TOC READING” is displayed. 2 Close the lid of the CD compartmen
ページ7に含まれる内容の要旨
Basic Operations Example of folder structure and playing order The playing order of the folders and files is as follows: CD-R Folder CD-RW MP3 file 1 1 2 Notes 3 4 • A folder that does not include an MP3 file is 4 5 skipped. • Maximum folder number: 6 255 Maximum file number: 255 5 7 • Folder names and file names can be displayed 8 with up to 8 characters. • The characters A - Z, 9 0 - 9, and _ can be displayed on this player. Other characters are 6 q; displayed as “-”. • The file name does not
ページ8に含まれる内容の要旨
Listening to the radio 12 Connect the supplied AC power cord (see page 23). RADIO 1 Press BAND•AUTO PRESET until Display the band you want appears in the display (direct power-on). BAND AUTO PRESET 2 Hold down + or – (TUNE + or – on Indicates an FM the remote) until the frequency digits stereo broadcast RADIO begin to change in the display. The player automatically scans the radio frequencies and stops when it BAND AUTO PRESET finds a clear station. If you can’t tune in a station, press the butt
ページ9に含まれる内容の要旨
Basic Operations Use these buttons for additional operations POWER VOLUME +, – MODE To Press adjust the volume VOLUME +, – (VOL +, – on the remote) Tip If the FM broadcast is turn on/off the radio POWER noisy, press MODE until “Mono” appears in the To improve broadcast reception display and radio will play in monaural. Reorient the antenna for FM. Reorient the player itself for AM. for FM for AM 9
ページ10に含まれる内容の要旨
Playing a tape 2 1 Connect the supplied AC power cord (see page 23). STOP/EJECT 1 Press xZ to open the tape With the side you want to play facing upward compartment and insert a recorded tape. Use TYPE I (normal) tape only. Close the compartment. PLAY 2 Press N. Display The player turns on (direct power-on) and starts playing. 10
ページ11に含まれる内容の要旨
Basic Operations Use these buttons for additional operations m M xZ X VOLUME +, – POWER To Press adjust the volume VOLUME +, – (VOL +, – on the remote) stop playback xZ fast-forward or rewind M or m pause playback X Press the button again to resume play after pause. eject the cassette xZ turn on/off the player POWER. 11
ページ12に含まれる内容の要旨
Recording on a tape 31 Connect the supplied AC power cord (see page 23). 1 Press xZ to open the tape With the side you want to STOP/EJECT record on facing upward compartment and insert a blank tape. Use TYPE I (normal) tape only. Close the compartment. 2 CD Select the program source you want to record. Display To record from the CD player, insert a CD (see page 4) and press x on the CD section. To record from the radio, tune in the RADIO station you want (see page 8). BAND AUTO PRESET 12
ページ13に含まれる内容の要旨
Basic Operations REC 3 Press z to start recording (N is depressed automatically). Use these buttons for additional operations xZ X POWER FUNCTION To Press Tips stop recording xZ • Adjusting the volume or the pause recording X audio emphasis (see page Press the button again to 21) will not affect the resume recording. recording level. • For the best results, use the turn on/off the player POWER AC power as a power source. • To erase a recording, proceed as follows: 1 Insert the tape whose recordi
ページ14に含まれる内容の要旨
The CD Player Checking the information of a Using the display disc with MP3 files You can check information about the CD Press DISPLAY/ENTER•MEMORY. The using the display. display will be changed as follows: During stop in TRACK and FOLDER mode* To display Press DISPLAY/ ENTER•MEMORY the number of total once folders and tracks DISPLAY/ ENTER “00” twice MEMORY Total track number Total folder number * While the resume function is worked, the Checking the information of information of the track to
ページ15に含まれる内容の要旨
The CD Player Tips • When you locate a track numbered over 10, Locating a specific press >10 first, then the corresponding number buttons. track Example: To play track number 23, press >10 first, then 2 and 3. You can quickly locate any track using the • To select a track numbered 100 or more, press number buttons on the remote. You can also >10 twice, then the corresponding number find a specific point in a track while playing buttons. a CD. POWER FUNCTION SLEEP (AC ONLY) CD/RADIO number button
ページ16に含まれる内容の要旨
Scanning the beginning Playing tracks of the tracks (Intro Scan) repeatedly (Repeat Play) You can scan the first 10 seconds of all the You can play tracks repeatedly in normal, tracks in the CD. shuffle or program play modes. INTRO SCAN MODE u Jog dial u x Press INTRO SCAN in stop mode. The indication in the display flashes and To repeat Do this the intro scan function starts. a single track 1 Press MODE until “REP 1” appears. To play the track you want to 2 Select the track by turning the jog d
ページ17に含まれる内容の要旨
The CD Player When playing MP3 files When you select “REP ALL” Playing tracks in • In TRACK mode, the player plays all files random order (Shuffle Play) (up to 255 files) of a disc repeatedly. • In FOLDER mode, the player plays all You can play tracks in random order. files (up to 255 files) in the selected folder repeatedly. Tip The resume function doesn't work during Repeat MODE Play. u x 1 Press x. “CD” appears in the display. 2 Press MODE until “SHUF” appears in the display. 3 Press u to sta
ページ18に含まれる内容の要旨
To cancel Program Play Press MODE until “PGM” disappears from Creating your own the display. program (Program Play) To check the order of tracks You can arrange the playing order of up to before play 20 tracks on a CD. Press DISPLAY/ENTER•MEMORY. Every time you press the button, the track number appears in the programed order. MODE To change the current program Press x once if the CD is stopped and twice DISPLAY/ ENTER if the CD is playing. The current program MEMORY will be erased. Then create
ページ19に含まれる内容の要旨
The Radio The Radio If a station cannot be preset automatically Presetting radio You need to preset a station with a weak stations signal manually. 1 Press BAND•AUTO PRESET to select You can store radio stations into the player’s the band. memory. You can preset up to 30 radio 2 Tune in a station you want. stations, 20 for FM and 10 for AM in any 3 Hold down DISPLAY/ENTER• order. MEMORY for about 2 seconds. 4 Turn the jog dial until the preset number you want for the station flashes in the BAND•
ページ20に含まれる内容の要旨
Playing preset radio stations Once you’ve preset the stations, use the jog dial on the player or the number buttons on the remote to tune in your favorite stations. BAND• AUTO PRESET Jog dial 1 Press BAND•AUTO PRESET to select the band. 2 Turn the jog dial to display the preset number of the station you want. On the remote 1 Press BAND to select the band. 2 Press the number buttons to tune in the stored station. To tune in a preset station over 10, press >10 first, then the corresponding number
