ページ1に含まれる内容の要旨
®
Hotwire 8300 Endpoint
Installation Instructions
Document Number 8300-A2-GN10-00
April 2003
Contents
Product Documentation Online ..................................................................... 1
Package Checklist ......................................................................................... 2
Preparation ................................................................................................... 2
Installing the Power Cord ...............................................
ページ2に含まれる内容の要旨
Package Checklist Verify that your package contains the following: ❑ 8300 Endpoint ❑ Power cord ❑ 8-pin modular cable for connection to the DSL network ❑ Ferrite choke for the Ethernet cable A DB9-to-DB9 cable for connection to an asynchronous terminal or PC (personal computer) is included with some models. Preparation Make sure you have: ❑ A dedicated, grounded power outlet that is protected by a circuit breaker within 6 feet of the 8300 Endpoint ❑ A clean, well-lit, and ventilated site that
ページ3に含まれる内容の要旨
Installing the Power Cord The POWER port on the unit is a standard, grounded, three-prong connector. The unit has no power switch. Figure 1. Hotwire 8300 Endpoint Back Panel Procedure 1. Insert the power cord’s receptacle into the POWER jack. 2. Plug the other end of the power cord into a grounded power outlet. 3. Check the LEDs. When power is applied to the unit, the front panel indicators flash for approximately 10 to 15 seconds as the unit initializes itself. The green POWER LED
ページ4に含まれる内容の要旨
Front Panel LEDs and Switches The front panel’s LED status indicators are described below: Indicator Description MODE Normally, this indicator lights green. The indicator lights amber while configuration is being set by the front panel buttons or when the configuration is changed by SNMP or through the web interface. The indicator will remain amber until the changed configuration is saved; it will revert to green when the new configuration has been saved. CBR The indicator is off (not illu
ページ5に含まれる内容の要旨
Connecting the Supervisory Port The SUPERVISORY port is a DB9 female DCE connector configured for 8 bits, no parity, and 1 stop bit. Bit rates are configured through the Web server interface. The initial default rate of the Supervisory port is 19200 bps. On power-up, the Supervisory port sends out diagnostic messages at the bit rate of 115.2 kbps until the Supervisory service acquires the Supervisory port, after which the port speed is changed to the setting in the Supervisory interface scre
ページ6に含まれる内容の要旨
Connecting the Ethernet Port The unit provides a single Ethernet interface port for IP Gateway, SNMP, and Web browser access. This interface is an eight-pin modular jack that complies with standard twisted-pair, 10/100BaseT requirements. Procedure 1. Insert one 8-pin connector of your Ethernet cable (not provided) into the 10/100_ETHERNET port. 2. Open the supplied ferrite choke and place it around the Ethernet cable as close to the 8300 Endpoint as possible. Close the choke and lock it by
ページ7に含まれる内容の要旨
Connecting the CBR Port The CBR (Constant Bit Rate) port is an RJ48C, eight-pin modular jack that is software-selectable for T1 or E1. As a T1 port, it terminates as 100 ohms, and as an E1 port at 120 ohms. This port is used to transport TDM traffic using a T1/E1 framer to provide ATM adaptation Layer 1 with Circuit Emulation Services (AAL1-CES). It must not be connected to outside plant wiring. Procedure 1. Plug an RJ48-to-RJ48 cable (not provided) into the CBR port. 2. Plug the other end o
ページ8に含まれる内容の要旨
Web Interface If you will use the Ethernet port for the web interface, you must set the IP address of the port, or use the default address of 192.168.6.1. The IP address of the 8300 Endpoint must be on the same subnet as the PC accessing the web interface. Setting the Ethernet Port Address To set the Ethernet port address: Procedure 1. Access the Main Menu as described in Connecting the Supervisory Port on page 5. 2. Tab to the Interfaces selection and press Enter. The Interfaces menu appears.
ページ9に含まれる内容の要旨
Accessing the Web Interface To access the web interface: Procedure 1. Start your web browser. Microsoft Internet Explorer version 5.0 or higher is recommended. 2. Type the IP address of the 8300 Endpoint’s Ethernet port into the Address field of the browser and press Enter. The Unit Screen appears. Click on the selections in the navigation frame on the left side of the screen to configure and monitor the unit. See the User’s Guide for more information. 9
ページ10に含まれる内容の要旨
! UNITED STATES – EMI NOTICE: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to rad
ページ11に含まれる内容の要旨
The Telephone Company may make changes in its facilities, equipment, operations or procedures that could affect the operation of the equipment. If this happens, the Telephone Company will provide advance notice in order for you to make necessary modifications to maintain uninterrupted service. If trouble is experienced with the 8300 Endpoint, refer to the repair and warranty information in this document. If the equipment is causing harm to the telephone network, the Telephone Company may
ページ12に含まれる内容の要旨
! Important Safety Instructions 1. Read and follow all warning notices and instructions marked on the product or included in the manual. 2. This product is intended to be used with a 3-wire grounding type plug — a plug which has a grounding pin. This is a safety feature. Equipment grounding is vital to ensure safe operation. Do not defeat the purpose of the grounding type plug by modifying the plug or using an adapter. Prior to installation, use an outlet tester or a voltmeter to check the
ページ13に含まれる内容の要旨
10. This unit is provided with a replaceable lithium battery. Replace the battery only with the same type recommended by the manufacturer. Discard used batteries according to the manufacturer’s instructions. Supplier’s Declaration of Conformity Place of Issue: Paradyne Corporation th 8545 126 Avenue North Largo, FL 33773-1502 USA Date of Issue: 4/4/2003 Paradyne Corporation, located at the above address, hereby certifies that the Hotwire® Model Number 8300-AX-400, bearing labeling identificat
ページ14に含まれる内容の要旨
Document Feedback We welcome your comments and suggestions about this document. Please mail them to Technical Publications, Paradyne Corporation, 8545 126th Ave. N., Largo, FL 33773, or send e-mail to userdoc@paradyne.com. Include the number and title of this document in your correspondence. Please include your name and phone number if you are willing to provide additional information. Trademarks FrameSaver is a registered trademark of Paradyne Corporation. All other products and services m
ページ15に含まれる内容の要旨
15
ページ16に含まれる内容の要旨
*8300-A2-GN10-00* 16
