ページ1に含まれる内容の要旨
ADSL2+ Modem
with Wireless
G+ MIMO Router
Network your
UK
computers and
FR
share your ADSL
DE
Internet access
NL
ES
IT
User Manual
F5D9630uk4A
ページ2に含まれる内容の要旨
Table of Contents 1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Benefits of a Home Network . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Advantages of a Belkin Wireless Network. . . . . . . . . . . . . . . . . . . . . . 1 2 Make Sure You Have the Following. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Package Contents. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
ページ3に含まれる内容の要旨
section Introduction Thank you for purchasing the Belkin ADSL Modem with High-Speed 1 Mode Wireless G Router (the Router). In minutes you will be able to share your Internet connection and network your computers with your new Router. The following is a list of features that make your Router 2 an ideal solution for your home or small office network. Please be sure to read through this User Manual completely, and pay special attention 3 to Appendix B entitled “Important Factors for Placement
ページ4に含まれる内容の要旨
Make Sure You Have the Following Package Contents • ADSL2+ Modem with Wireless G+ MIMO Router • RJ11 Telephone Cord - Gray • RJ45 Ethernet Networking Cable - Yellow • ADSL Microfilter* • Power Adapter • User Manual CD *ADSL microfilter varies by country. If it’s not included, you will need to purchase one. System Requirements • An active ADSL service with a telephone wall jack for connecting the Router • At least one computer with a Network Interface Card (NIC) and Internet browser
ページ5に含まれる内容の要旨
section Knowing your Router 1 The Router is designed to be placed on a desktop. All of the cables exit from the rear of the Router for better organization and utility. The LED indicators are easily visible on the front of the Router to provide you with information 2 about network activity and status. 3 Front Panel (1) (2) (5) (4) (3) 4 5 6 1. Power LED When you apply power to the Router or restart it, a short period of time 7 elapses while the Router boots up. When the Router has complete
ページ6に含まれる内容の要旨
K Kn no ow wi in ng g y yo ou ur r R Ro ou ut te er r 3. WLAN Status LED The WLAN Status LED is solid GREEN when you enable the wireless LAN function. It flashes when the Router is transmitting or receiving data wirelessly. OFF W LAN is off Green W LAN is up and connected Green - blinking W hen transmitting or receiving data 4. ADSL LED The ADSL LED flashes GREEN during negotiation with your ISP. It stays GREEN when the Router is connected properly to your ADSL service. OFF N o ADSL
ページ7に含まれる内容の要旨
section Knowing your Router 1 Back Panel 2 3 (6) (7) (8) (9) 4 5 6 6. D SL Line This port is for connection to your ADSL line. Connect your ADSL 7 line to this port. 7. E thernet Ports 8 The Ethernet ports are RJ45, 10/100 auto-negotiation. The ports are labeled 1 through 4. These ports correspond to the numbered LEDs on the front of the Router. Connect your network-enabled 9 computers or any networking devices to one of these ports. 8. Reset Button 10 T he “Reset” button is used in
ページ8に含まれる内容の要旨
C Co on nn ne ec ct ti in ng g y yo ou ur r R Ro ou ut te er r Positioning your Router Your wireless connection will be stronger the closer your computer is to your Router. Typical indoor operating range for your wireless devices is between 100 and 200 feet. In the same way, your wireless connection and performance will degrade somewhat as the distance between your Router connected devices increases. This may or may not be noticeable to you. As you move farther from your Router, connecti
ページ9に含まれる内容の要旨
section Connecting your Router 1 Connecting your Computers 2 1. Power off your computers and networking equipment. 2. C onnect your computer to one of the YELLOW RJ45 ports on the 3 rear of the Router labeled “connections to your computers” by using an Ethernet networking cable (one Ethernet network cable is supplied). 4 5 6 7 8 9 10 12 7 7
ページ10に含まれる内容の要旨
C Co on nn ne ec ct ti in ng g y yo ou ur r R Ro ou ut te er r Connecting your ADSL Line Connection for the Router to the ADSL line varies by country and region. Typically it involves a microfilter or a microfilter with built- in splitter to allow simultaneous use of ADSL service and telephone service on the same telephone line. Please read the following steps carefully and select appropriate method. 1. If your telephone service and ADSL service are on the same telephone line, ADSL micro
ページ11に含まれる内容の要旨
section Connecting your Router 1 2 3 4 5 6 7 8 Note: One RJ11 telephone cord is supplied. When inserting an RJ11 plug, be sure the tab on the plug clicks into position to 9 ensure that it is properly seated. 10 3. If you have a dedicated ADSL service telephone line with an RJ11 wall jack, simply connect a telephone cord from the wall jack to the gray RJ11 port labeled “DSL line” on the back of your Router. 12 4. If you have an RJ45 wall jack for your ADSL service, connect an RJ45-to-RJ1
ページ12に含まれる内容の要旨
Connecting your Router Powering Up your Router 1. C onnect the supplied power adapter to the Router power-input plug labeled “Power”. Note: For safety and performance reasons, only use the supplied power adapter to prevent damage to the Router. 2. After connecting the power adapter and the power source is turned on, the Router’s power icon. on the front panel should be on. It might take a few minutes for the Router to fully start up. 3. T urn on your computers. After your computers boo
ページ13に含まれる内容の要旨
section Setting Up your Computers 1 In order for your computer to properly communicate with your Router, you will need to change your computer’s “TCP/IP Ethernet” settings to “Obtain an IP address automatically/Using DHCP”. This is normally the default 2 setting in most home computers. You can set up the computer that is connected to the ADSL modem 3 FIRST using these steps. You can also use these steps to add computers to your Router after the Router has been set up to connect to the Inter
ページ14に含まれる内容の要旨
S Se et tt ti in ng g U Up p y yo ou ur r C Co om mp pu ut te er rs s Manually Configuring Network Adapters in Windows 98SE or Me 1. Right-click on “My Network Neighborhood” and select “Properties” from the drop-down menu. 2. Select “TCP/IP -> settings” for your installed network adapter. You will see the following window. (1) (3) (2) 3. If “Specify an IP address” is selected, your Router will need to be set up for a static IP connection type. Write the address information in the tabl
ページ15に含まれる内容の要旨
section Setting Up your Computers 1 Set up the computer that is connected to the cable or DSL modem by FIRST using these steps. You can also use these steps to add computers to your Router after the Router has been set up to connect 2 to the Internet. 3 Manually Configuring Network Adapters in Mac OS up to 9.x 4 5 In order for your computer to properly communicate with your Router, you will need to change your Mac computer’s TCP/IP settings to DHCP. 6 1. P ull down the Apple menu. Select
ページ16に含まれる内容の要旨
S Se et tt ti in ng g U Up p y yo ou ur r C Co om mp pu ut te er rs s 4. I f not already set, at “Configure:”, choose “Using DHCP Server”. This will tell the computer to obtain an IP address from the Router. 5. Close the window. If you made any changes, the following window will appear. Click “Save”. R estart the computer. When the computer restarts, your network settings are now configured for use with the Router. 14 14 15 15
ページ17に含まれる内容の要旨
section Setting Up your Computers 1 Manually Configuring Network Adapters in Mac OS X 1. Click on the “System Preferences” icon. 2 3 4 2. Select “Network” (1) from the “System Preferences” menu. 5 6 (1) 7 8 9 3. Select “Built-in Ethernet” (2) next to “Show” in the Network menu. 10 (2) 12 (3) (4) 15 15
ページ18に含まれる内容の要旨
S Se et tt ti in ng g U Up p y yo ou ur r C Co om mp pu ut te er rs s 4. Select the “TCP/IP” tab (3). Next to “Configure” (4), you should see “Manually” or “Using DHCP”. If you do not, check the PPPoE tab (5) to make sure that “Connect using PPPoE” is NOT selected. If it is, you will need to configure your Router for a PPPoE connection type using your user name and password. 5. I f “Manually” is selected, your Router will need to be set up for a static IP connection type. Write the addr
ページ19に含まれる内容の要旨
section Setting Up your Computers 1 Recommended Web Browser Settings In most cases, you will not need to make any changes to your web 2 browser’s settings. If you are having trouble accessing the Internet or the advanced web-based user interface, then change your browser’s settings to the recommended settings in this section. 3 4 5 6 7 8 9 10 Internet Explorer 4.0 or Higher 1. Start your web browser. Select “Tools” then “Internet Options”. 12 2. In the “Internet Options” screen, there a
ページ20に含まれる内容の要旨
Setting Up your Computers 4. Make sure there are no check marks next to any of the displayed options: “Automatically detect settings”, “Use automatic configuration script”, and “Use a proxy server”. Click “OK”. Then click “OK” again in the “Internet Options” page. Netscape Navigator 4.0 or Higher 1. Start Netscape. Click on “Edit” then “Preferences”. 2. In the “Preferences” window, click on “Advanced” then select “Proxies”. In the “Proxies” window, select “Direct connection to the Int
