ページ6に含まれる内容の要旨
Accessories Operating instructions ..................................................... 1 Wire mounting screws Rotary arm ......................................................................... 1 (with flat washers, spring washers) Camera mounting base .................................................... 1 M4 8 mm ............................................................... 2 Mounting screws for the rotary arm and camera Inch screw ................................................
ページ7に含まれる内容の要旨
Parts and their function 7
ページ8に含まれる内容の要旨
Parts and their function Rotary head PROMPTER connector This rotates in the horizontal direction. The prompter is connected to this connector. The maximum current which can be supplied from the DC 1 V OUT socket is .5 A. Pedestal When the prompter is connected, the pan-tilt head’s speed is reduced to about one-third. POWER ON/OFF switch When connecting the prompter, be absolutely sure to Where a switch is pushed in, the unit’s power is turned short-circuit the DETECT terminal (
ページ9に含まれる内容の要旨
Parts and their function Rotary head connector panel ND/EXT connector [ND/EXT] LENS P/S ON/OFF switch [LENS P/S] This is for the control of the ND filter and lens extender of When this is set to ON, power is supplied to the lens from the motorized lens unit. the LENS I/F (1) connector. When it is set to OFF, power Connect this connector when using a motorized lens is no longer supplied to the lens from the LENS I/F (1) unit with ND filter and lens extender functions. The cable connector.
ページ10に含まれる内容の要旨
Parts and their function Pedestal connector panel CONTROL IN RP connector [RP] AUX connector [AUX] This is the connector for the control of signals of the This is the output connector for the camera’s video camera and pan-tilt head. signals. It is connected to the TO PAN/TILT HEAD connector on It enables the SDI signals, VBS signals, etc. from the the AW-RP655 multi-function controller and AW-RP555 BNC coaxial cable connected to AUX IN to be output. multi hybrid control panel. Provide a BN
ページ11に含まれる内容の要旨
Installation Assembling the pan-tilt head When assembling the pan-tilt head, use the Allen key (provided) and screwdriver, and secure the head by tightening the screws firmly. After mounting the pan-tilt head, check there is no play in its installation. Attaching the camera mounting base Attach the camera mounting base to the rotary arm using the three mounting screws (M5 mm, with flat washers, spring washers) provided. The installation direction differs depending on how the base is in
ページ12に含まれる内容の要旨
Installation Mounting the tally lamp Connect the cable connector which is taped to the top of the pan-tilt head to the tally cable connector. Mount the tally lamp on the top of the pan-tilt head using the two screws provided. Mount the lamp while paying attention to the wire. The cable for the tally cable connector is about -1/16” (50 mm) long. When connecting the cable to the connector, do not pull it out beyond this length. If the tally lamp is not going to be used, insert the cable wh
ページ13に含まれる内容の要旨
Installation Concerning the safety modes This unit comes with two safety modes which are designed to safeguard the user and others from injury and to prevent damage to the pan-tilt head. 1. Mode for ensuring safety in the case of collisions When the rotary arm of the pan-tilt head or some other unit installed on the head keeps colliding with an obstruction or a person (approx. 6 seconds when the head rotates at 45 degrees per second), the mode for ensuring safety in the case of collisions i
ページ14に含まれる内容の要旨
Installation Procedure for changing the settings of the CPU circuit board switches Follow the steps below to change the settings of the CPU circuit board switches. Remove the four screws, and gently remove the housing case. Disconnect the tally cable connector. Set the switches on the CPU circuit board. After you have performed the settings, connect the tally cable connector, and then return the housing case to its original position, and attach it using the screws. (Take care to ensu
ページ15に含まれる内容の要旨
Installation Setting the CPU circuit board switches CPU circuit board Magnification of the CPU circuit board Setting SW1 These switches are used to set the operations of the AW-PH405. Before changing their settings, make sure that the power has been turned off. No.1: A uto focus (AF)/extender (EXT) selector switch. Use this at the ON position when using an auto focus lens which is connected to the LENS I/F (1) connector; use it at the OFF position when using a lens with a motorized exten
ページ16に含まれる内容の要旨
Installation Pan-tilt head mounting conditions Camera Pan-tilt Mounting Compatible Camera Compatible Cable anti-drop Lens weight Total weight head weight specifications cameras weight lenses weight measures Convertible camera series Approx. AW-E50 AW-LZ16MD55P Approx. .6 lbs Approx. .9 lbs AW-E650 AW-LZ16MD7P 8.7 lbs (1. kg) (1. kg) max. Stand-alone AW-E655 AW-LZ17MD9AG (1 kg) Wire provided Approx. max. Approx. lbs installation or AW-E750 used for 0.7 lbs (10
ページ17に含まれる内容の要旨
Installation For a stand-alone installation For installation on the ceiling When installing the pan-tilt head, do not forcibly turn the rotary head or rotary arm Note manually. Doing so may result in malfunctioning. 17
ページ18に含まれる内容の要旨
Installation Mounting the camera [Convertible camera AW-E350/E650/E655/E750/E860] When mounting the camera, take sufficient care to ensure that the camera will not come off or fall down. Mount the lens onto the convertible camera. (Before mounting a large lens, consult with your dealer.) Mount the convertible camera after aligning it with the guide pins. Use a tool to tighten up the mounting screws so that they are securely tightened. For a stand-alone installation Set the guide pi
ページ19に含まれる内容の要旨
Installation Attaching the wire [Convertible camera AW-E350/E650/E655/E750/E860] The camera comes with a wire for preventing the camera from dropping. Follow the instructions below to use it to couple the camera to the pan-tilt head. When mounting the cameras with fan (AW-E655, AW-E750, AW-E860) Use the wire mounting scre w (M4 8 mm with flat washer and spring washer) to attach one end of the wire to the pan-tilt head’s arm. Mount the mounting spacer on the top panel of the camera. (T
ページ20に含まれる内容の要旨
Installation Mounting the camera [Multi-purpose camera AK-HC1500G] When mounting the camera, take sufficient care to ensure that the camera will not come off or fall down. Mount the lens onto the multi-purpose camera. (1) Lenses that can be used The current r ating of LENS • Use any of the portable lenses which are listed below. Note I/F () connector is 500 mA Fujinon HA18, HA1, HA series (max). Canon HJ17e, HJ1e series Even with the lenses in a series which can be used,
