ページ1に含まれる内容の要旨
MODEL G9017/G9018
HYDRAULIC TUBE BENDER
INSTRUCTION SHEET
COPYRIGHT © OCTOBER, 2005 BY GRIZZLY INDUSTRIAL, INC.
WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE
OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC.
#BL7554 PRINTED IN CHINA
ページ2に含まれる内容の要旨
Introduction Inventory (Figures 1 & 2) The Model G9017/G9018 (Figure 1) is designed A. Bender ........................................................ 1 1 3 1 1 for bending thick walled pipes (schedule 40 and B. Dies, (G9017) ⁄2", ⁄4", 1", 1 ⁄4", 1 ⁄2", 2") ..... 6 1 3 1 1 1 80) and has six different bending dies ranging C. Dies, (G9018) ⁄2", ⁄4", 1", 1 ⁄4", 1 ⁄2", 2", 2 ⁄2", 1 in size from ⁄2" to 2" for the G9017 (see Figure 3") ............................................................... 8
ページ3に含まれる内容の要旨
5. Reinstall the roller shafts and hitch pins. OPERATION To bend a pipe: 6. Place the pipe over the bending die. 1. Insert the pump handle bar into the socket on Note: To account for pipe shortening dur- the tube bender shown in Figure 1. ing the bend, make sure the pipe extends beyond the rollers (Figure 5) and, for short 2. Choose the proper size bending die and slip it pipe, set the rollers closer together, as shown on the end of the ram as shown in Figure 3. in Figure 6. Bending Di
ページ4に含まれる内容の要旨
• Pipes bent past 90˚ will flow into the bending die, making the pipe hard to remove after bending. Greasing the inside of the die will Never use a cheater pipe extension on the make this removal easier, or switching to a hydraulic pump handle. Failure to comply larger die for bending the last few degrees may result in personal injury. will eliminate this difficulty. 7. Make sure the release valve is closed, then MAINTENANCE use the pump handle bar (Figure 7) to • The Model G9017 and G9
ページ5に含まれる内容の要旨
G9017 Parts Breakdown � � � �� �� �� � �� �� � � �� �� �� � �� �� � � �� G9017 Parts List REF PART # DESCRIPTION REF PART # DESCRIPTION 1 P9017001 FRAME 11 P9017011 1-1/2" BENDING DIE 2 P9017002 12 TON BOTTLE JACK 12 P9017012 2" BENDING DIE 3 PSB146M CAP SCREW M10-1.5 X 15 13 P9017013 PUMP HANDLE BAR 4 P9017004 ROLLER SHAFT 14 P9017014 SPRING PLATE 5 P9017005 ROLLER 15 P9017015 EXTENS. SPRING 35 X 4.5 X 21.5 6 P9017006 HITCH PIN 16 P9017016 EYE BOLT 7 P9017007 1/2" BENDING DIE 17 PN03M HEX NUT M
ページ6に含まれる内容の要旨
G9018 Parts Breakdown � � �� �� � �� �� �� � �� � � �� �� � �� �� �� � � G9018 Parts List REF PART # DESCRIPTION REF PART # DESCRIPTION 1 P9018001 FRAME 11 P9018011 1-1/2" BENDING DIE 2 P9018002 16 TON LONG RAM JACK 12 P9018012 2" BENDING DIE 3 PSB61M CAP SCREW M10-1.5 X 20 13 P9018013 2-1/2" BENDING DIE 4 P9018004 ROLLER SHAFT 14 P9018014 3" BENDING DIE 5 P9018005 ROLLER 15 P9018015 PUMP HANDLE BAR 6 P9018006 HITCH PIN 16 P9018016 SPRING PLATE 7 P9018007 1/2" BENDING DIE 17 P9018017 EXTENS. SPR
ページ7に含まれる内容の要旨
WARRANTY CARD Name _____________________________________________________________________________ Street _____________________________________________________________________________ City _______________________ State _________________________ Zip _____________________ Phone # ____________________ Email ________________________ Invoice # _________________ Model # ____________________ Order # _______________________ Serial # __________________ The following information is given on a voluntary bas
ページ8に含まれる内容の要旨
FOLD ALONG DOTTED LINE Place Stamp Here GRIZZLY INDUSTRIAL, INC. P.O. BOX 2069 BELLINGHAM, WA 98227-2069 FOLD ALONG DOTTED LINE Send a Grizzly Catalog to a friend: Name_______________________________ Street_______________________________ City______________State______Zip______ TAPE ALONG EDGES--PLEASE DO NOT STAPLE
