ページ1に含まれる内容の要旨
INSTALLATION INSTRUCTIONS
30" (76.2 CM) ELECTRIC BUILT-IN
MICROWAVE/OVEN COMBINATION
Table of Contents
BUILT-IN MICROWAVE/ OVEN COMBINATION SAFETY..........1
INSTALLATION REQUIREMENTS ................................................2
Tools and Parts ............................................................................2
Built-In Microwave/Oven Combination
Location Requirements................................................................2
Water Filtration System Location Requirements.
ページ2に含まれる内容の要旨
INSTALLATION REQUIREMENTS Tools and Parts Built-In Microwave/Oven Combination Gather the required tools and parts before starting installation. Location Requirements Read and follow the instructions provided with any tools listed Make sure you have everything needed for correct installation. here. IMPORTANT: Observe all governing codes and ordinances. ■ Cabinet opening dimensions that are shown must be used. Tools needed Given dimensions provide minimum clearance with oven. ■ Adjustable wre
ページ3に含まれる内容の要旨
Depending on your installation configuration, more routing holes Cabinet Dimensions may be required. Typical Installation Configuration A NOTE: For unique installations contact a licensed plumber. B Cold water supply F D Hot Cold Filter assembly location E C A. 30" (76.2 cm) min. cabinet width Water Supply Requirements B. 1" (2.5 cm) top of cutout to bottom of upper cabinet door A cold water supply with water pressure between 30 and 120 psi C. 19¹⁄₄" (48.9 cm) bottom of cutout to floor (207
ページ4に含まれる内容の要旨
Electrical Connection ■ Models rated from 7.3 to 9.6 kW at 240 volts (5.5 to 7.2 kW at 208 volts) require a separate 50-amp circuit. Models rated To properly install your oven, you must determine the type of at 7.2 kW and below at 240 volts (5.4 kW and below at electrical connection you will be using and follow the instructions 208 volts) require a separate 30-amp circuit. provided for it here. ■ Oven must be connected to the proper electrical voltage and ■ A circuit breaker is recommended.
ページ5に含まれる内容の要旨
Make Electrical Connection 4-Wire Cable from Home Power Supply WARNING IMPORTANT: Use the 4-wire cable from home power supply in the U.S. where local codes do not allow grounding through neutral, New Branch circuit installations (1996 NEC), mobile homes and recreational vehicles, new construction and in Canada. A Electrical Shock Hazard B E Disconnect power before servicing. F Use 8 gauge solid copper wire. G Electrically ground oven. Failure to follow these instructions can result in death,
ページ6に含まれる内容の要旨
1. Connect the 2 black wires (C) together using a UL listed wire connector. Connect to Water Filter Inlet (yellow) 2. Connect the 2 white wires (D) and the green (or bare) ground NOTE: Use the quick connect stem and/or elbow adapter fittings wire (of the oven cable) using a UL listed wire connector. in the combination needed for your installation configuration. 3. Connect the 2 red wires (G) together using a UL listed wire 1. Attach the supplied ³⁄₈" to ¹⁄₄" stem or ³⁄₈" to ¹⁄₄" elbow quick
ページ7に含まれる内容の要旨
3. Pull tube to ensure it is secured. Install Oven Copper water supply tubing to oven Sink WARNING Water Excessive Weight Hazard supply connection Use two or more people to move and install oven. Yellow Failure to do so can result in back or other injury. WATER IN 1. Using 2 or more people, lift oven partially into cabinet cutout using the oven opening as an area to grip. Blue Copper water supply NOTE: Push against seal area of oven front frame when WATER tubing to Shutoff OUT pushing oven i
ページ8に含まれる内容の要旨
5. On some models, the oven vent is taped to the side of the 6. Replace oven racks. oven. 7. Replace oven door(s) by inserting ends of hinges into hinge With one #8-14 x ³⁄₈" screw for each side of the vent, fasten slots in the oven frame. vent securely to the oven. 8. Push hinges in as far as they will go and open the oven door. You should feel the oven door drop into place. 9. Rotate both hinge latches back to the locked position. 10. Check that the door is free to open and close. If it is
