ページ1に含まれる内容の要旨
Installation Instructions
for
®
Thermador Microwave MBY
(Sold Separately)
Built-In Trim Kits • Models MT27 & MT30
SENSOR SENSOR
REHEAT COOK
POWER POP
LEVEL CORN
1 2 3
4 5 6
7 8 9
CLOCK
TIMER 0
MORE QUICK FUNCTION
/LESS MIN KEY
SERVING KEEP TURBO
/WEIGHT WARM DEFROST
STOP/RESET START
Please Read this entire manual before proceeding:
IMPORTANT: Local codes vary. Installation, electrical connections, circuit breakers
and grounding must comply with all applicable codes. Save these
instructions for
ページ2に含まれる内容の要旨
Step 1: Unpacking A. Microwave Oven Model MBY (Sold Separately) Open the box and carefully remove fillers and all packing material. Included with your new Thermador microwave are the following: • Care and Use manual (1) • Quick Guide (1) • Warranty Card (1) • Turn Table (1) • Turn Table Support (1) B. Trim Kit Models MT27 & MT30 Open the box and carefully remove fillers and all packing materials. Parts list: Table 1 • Trim Frame (1) • Base Pan (1) TRIM KITS Microwave Oven Models • Trim Bracke
ページ3に含まれる内容の要旨
➛ ➝ ➛ ➛ ➝ ➛ ➛ ➛ ➝ Step 2: Cabinet Preparation • The cabinet cut out dimensions are shown in •Your microwave oven can be installed into a Figure 1. cabinet or wall by itself or above any of the following : Thermador wall ovens C271, C301, • It is good practice, when microwave oven is CM301, S301, SC301, CJ301 or Thermador installed at the end of a cabinet run, adjacent Warming Drawers WD 27 and WD 30 (See to a perpendicular wall or cabinet door, to al- Figure 2). low at least 1/4" space between
ページ4に含まれる内容の要旨
➝ Step 4: Installing the Trim Kit A. Position the 2 vertical trim brackets using the template as shown on Figure 3. Trim Brackets Figure 3. Centerline cutout Notch to mark ➝ the center line of the cutout. 1 Screws #8 x /4 . ➝ Template Template is used to locate the positions of the left and right trim brackets with respect to the cut out. The trims are secured with (3) screws each and the tem- plate is discarded after. Mark the center line of the cut out using the template. 1 Screws #8 x /4 F
ページ5に含まれる内容の要旨
Step 5: Installing The Microwave Oven (Figure 5) Note: The four (4) ducts have a plastic cover- 4. Remove and retain outer case screw at rear ing that must be removed prior to installing of the oven (right side) these ducts onto the microwave section. These 5. Install the grommet and the electrical cord ducts have sharp edges. Be careful when han- of the microwave in the receiving hole pro- dling. vided in the rear intake duct, and position this duct on rear of the oven (right side). 1. Remove
ページ6に含まれる内容の要旨
Step 5: Installing The Microwave Oven (continued) 9. Remove the left side vertical trim bracket (3 screws) (for MT27 only) 10. Slide the assembled microwave oven in the prepared cabinet cutout. Plug the electrical cord in the wall receptacle (ask help from another person). Align the microwave oven legs to the pan channel holes (Figure 6). 11. Install back the left side vertical trim bracket. (3 screws) Figure 6. 12. Snap on the frame trim with the “Therma- dor Logo under the microwave door bu
ページ7に含まれる内容の要旨
Notes Page 7
ページ8に含まれる内容の要旨
Thermador reserves the right to change specifications or design without notice. Some models are certified for use in Canada. Thermador is not responsible for products which are transported from the United States for use in Canada. Check with your local Canadian distributor or dealer. Thermador, 5551 McFadden Avenue, Huntington Beach, CA 92649. For the most up to date critical installation dimensions by fax, use your fax handset and call 702/833-3600. Use code #8030. 5551 McFadden Avenue, H
