ページ1に含まれる内容の要旨
Operating
Instructions
NE-1027/NE-1037
1000 Watts Microwave Oven
0 0 1 1 2 2
3 3
( (Min Min) ) 4 4
5 5
30 30 6 6
7 7
8 8
9 9
10 10
25 25
15 15
20 20
x2 12 3
X2
R
Please read these instructions completely before operating this oven.
ページ2に含まれる内容の要旨
Table of Contents For Your Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 Unpacking Your Oven . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 Placement of Your Oven . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 Using Your Oven . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 Maintenance of Your Ove
ページ3に含まれる内容の要旨
MICROWAVE Guarantee Card For Your Safety This appliance is supplied with a moulded three pin IMPORTANT: The wires in this mains lead are mains plug for your safety and convenience. A 13 coloured in accordance with the following code: amp fuse is fitted in this plug. Should the fuse need Green-and-yellow: Earth to be replaced, please ensure that the replacement Blue: Neutral fuse has a rating of 13 amps and that it is approved Brown: Live by ASTA or BSI to BS1362. Check for the ASTA As the colour
ページ4に含まれる内容の要旨
Placement of Your Oven 1. Oven must be placed on a flat, stable surface. For 3. Do not block air vents on the rear and bottom of proper operation, the oven must have sufficient air the cabinet. If air vents are blocked during flow, i.e. 5 cm/2" at the side; 15 cm/6" clear over operation, the oven may overheat. If the oven the top; 10 cm/4" at the rear. overheats, a thermal safety device will turn the oven off. The oven will remain inoperable with 2. Do not place the microwave oven on a shelf bla
ページ5に含まれる内容の要旨
Important Information –– Read Carefully Short Cooking Times 5. Foods with Skins As microwave cooking times are much shorter than Potatoes, apples, egg other cooking methods it is essential that yolk, whole vegetables recommended cooking times are not exceeded and sausages are without first checking the food. examples of food with non porous skins. These must Factors that may affect cooking times are: preferred be pierced using a fork degree of cooking, starting temperature, altitude, before cook
ページ6に含まれる内容の要旨
Important Information –– Read Carefully ?? ?????? ??????? ??????? ??????? ?O2@0M ?O2@@0M? O2@@0M ?O2@@@@0M?gI4@@@@@6K? ?O2@@@@@@@@@@@6K ?I4@@6K?I4@@6K I4@6K? ??????? 11. Reheating ?W&(Y? J@5??7@H?W&(Y? W&(M?W2@0M ?O2@0M ?I’6K? V4@6X? I’)K?V’@@? V’@L?V’)X? V’1? ?????? ? 14. Babies Bottles and Food Jars ?75??J@H ?7(Y75J@H??W&(Y? W&(Y ?N@L ?N@131?3)XN@L? 3@L?V’1? ??????? ?7@??@H??@5??J@? @H J@H?75 ?N@? @1 3@N@W)X??@@@)X@L?@?I’)K? ?????? ? W2@0Y?@@ O&(Y@@?W2@@@ ?O&@ ?@J@?@ 75he?3@? ?7@0Y?f?V’@L?J@he
ページ7に含まれる内容の要旨
How Does the Microwave Work? Microwaves are a form of high frequency radio Absorption waves similar to those used by a radio including During heating, microwaves will be absorbed by AM, FM and CB. They are, however, much shorter food. They penetrate to a depth of about 1- 5 cm than radio waves; approximately 12 cm long. Microwave energy excites the molecules in the food Electricity is converted into microwave energy by (especially water, fat and sugar molecules), and the magnetron tube. From the
ページ8に含まれる内容の要旨
NE-1027 Outline Diagram NE-1027 (1) Timer Select Dial (2) Power Select Dial (3) Start Button 0 1 2 3 (Min) 4 5 (4) Control Panel 30 6 7 8 (1) 9 (5) Door Safety Lock System 10 25 (6) Oven Window 15 20 (7) Oven Lamp (2) (7) 0 1 2 2 3 3 ( (Min Min) ) 4 4 5 5 30 30 6 6 7 7 8 8 9 9 10 10 25 25 15 15 20 20 (4) (6) (3) (5) How to Operate Heating 1. • Turn the Timer Select Dial to the desired position. 0 1 2 3 (Min) 4 Note: 5 30 6 • When selecting the time for shorter than 4 minutes, 7 8 9 turn the Tim
ページ9に含まれる内容の要旨
- MEMO - - 8 -
ページ10に含まれる内容の要旨
NE-1037 Outline Diagram NE-1037 (1) Digital Display Window (see below) (2) Power Level Pad x2 12 3 (3) Program Pad (1) (4) Double Quantity (x2) Pad (5) Start Pad (6) Stop/Reset Pad 1 (2) (7) Memory Pads (8) Control Panel 2 (9) Door Safety Lock System 3 (3) (10) Oven Window (11) Oven Lamp 4 (7) 5 (4) X2 (11) 6 x2 1 3 7 1 (5) 2 3 8 4 (8) 5 X2 (10) 6 7 8 9 9 0 (6) 0 (9) Digital Display Window Indicator Locations B A x2 12 3 D C E A - Program Change Indicator E - Power Level Indicator B - Double Qu
ページ11に含まれる内容の要旨
How to Operate Before Operating Make sure the oven is connected to a properly earthed electrical outlet. When the door is closed, the display is still blank. When the door is opened, the display shows “0”. For the detailed operation, see the page on each feature. This oven is preset at the factory for the following: 1. Memory Pads preset to 1000 W at the indicated heating times for single stage heating. Pad No. 1 2 3 4 5 6 7 8 9 0 1 min. 2 min. 3 min. Time 10 sec. 20 sec. 30 sec. 45 sec. 1 min.
ページ12に含まれる内容の要旨
NE-1037 How to Operate Heating Open the door and place the food in the oven cavity. Close the door. “0” must be showing in the display window. A. Manual Single Stage Heating: This feature gives the user maximum flexibility to set the oven to desired heating time and power level. This is ideal for menus that require various heating requirements. Example: To heat for 2 minutes at 1000 W 1 1. • Press the Power Level Pad once. 1 2. • Press the Memory Pads 2, 0 and 0. 2 0 0 3. 1 • Press the Start Pad
ページ13に含まれる内容の要旨
How to Operate C:Programmed Heating: Example: 1 stage; Memory Pad 9 to heat for 3 minutes at 1000 W 1. 1 • Press the Memory Pad 9. In Program 9 Lock Mode the oven will start without pressing the Start Pad. (See page 16) 1 2. • Press the Start Pad. Heating will start. The time on digital display will count down. 3. Beep tone will sound. • All heating will stop. When opening the (See page 18) door, the display will stop blinking. Example: 2 stages; Memory Pad 3 to heat for 3 minutes at 1000 W and
ページ14に含まれる内容の要旨
NE-1037 How to Operate Programming DO NOT OPEN THE DOOR The display window MUST be blank before programming. If any indicator light is illuminated in the digital display window: close the door, press the Stop/Reset Pad and wait 1 minute until the display goes blank. A. Programming Memory Pads for Single Stage Heating: Example: To program 30 seconds at 500 W for Memory Pad 5 1. • Press the Program Pad. Note: • If no “ ” Indicator appeared on display, “Program Lock” should be cancelled. (See page
ページ15に含まれる内容の要旨
How to Operate B. Programming Memory Pads for 2 or 3 Stages Heating: Example: To program for 2 minutes at 340 W for 2nd stage heating using Memory Pad 5 1 1. Complete steps 1 to 4 on page 13. • Program the 1st stage for 30 seconds at 500 W. 12 2. • Press the Power Level Pad 3 times. “ ” is now displayed. 12 3. • Press the Memory Pads 2, 0 and 0. 2 0 0 12 4. • Press the Program Pad again. You have completed programming the selected Memory Pad for 2 stages heating. Double heating time for double q
ページ16に含まれる内容の要旨
NE-1037 How to Operate C. Programming the Double Quantity Pad: Your oven is preset at the factory to automatically double the programmed time for double quantity heating. This model allows you to customize the heating time and/or power level for double quantity of your menu items. For example, if Memory Pad 2 is set for 20 seconds at 1000 W, 40 seconds at 1000 W is set for double quantity heating automatically. However, if your own tests have determined that the correct heating time required for
ページ17に含まれる内容の要旨
How to Operate Other Features A. To Activate Program Lock: This procedure locks the Memory Pads into their programmed heating times and power levels. DO NOT OPEN THE DOOR. 1. The display window must be blank. 2. • Press and hold in the Program Pad (for 5 seconds) until the display shows “P” and “L”. • Program Lock feature is now activated. NOTE: • In “Program Lock” a. To activate preset programs, open door will display “0”. b. The oven is started by pressing the desired Memory Pad. There is no n
ページ18に含まれる内容の要旨
NE-1037 How to Operate C. To Read Program List: Allows you to review all currently programmed pad number, heating time and power level for each stage. 1. Open the door. 2. • While pressing the Stop/Reset Pad, 1 + press the Start Pad. The beep tone setting will be shown in the display window. Example: Stage Indicator 1: Beep tone is ON. Stage Indicator 2: Beep tone is OFF. • 2 seconds later, the Program Lock setting will be shown in the display window. Program Lock: “P L” Program Unlock: “P” 1
ページ19に含まれる内容の要旨
How to Operate D. To Select Beep Tone Options: The Beep Tone can be set, ON or OFF. 1. Open the door. 2. • Press the Program Pad. The display will not change. 1 3. • Press the Memory Pad 0. 0 • Repeat pressing the Memory Pad 0. 4. 2 0 Select “OFF” of Beep Tone. Stage Indicator 1 = ON Stage Indicator 2 = OFF 2 5. • Press the Program Pad again. You have completed programming the beep tone. • 2 seconds later, “0” will appear in the display. E. To Read the Cycle Counter: The oven can display the tot
ページ20に含まれる内容の要旨
Self Diagnostics Failure Code This oven monitors its operation and displays a Failure Code in the display window when a problem occurs. What to do when a failure code appears: CODE CAUSE WHAT TO DO F01 * Overcooked food * Press Stop/Reset Pad to stop beep. * Temperature of exhausted air is too * Unplug the oven and wait at least high 30 minutes before reconnecting. * Wait for the oven to cool down and reset. * If a flame is observed, do not open the oven door. * If normal operation does not resu
