ページ1に含まれる内容の要旨
Operation Manual
LRM 1200 / LRM 1500
LRM 1500SPD
LASER RANGEFINDER MONOCULAR
105 Sparks Ave., Toronto, ON M2H 2S5, Canada
ページ2に含まれる内容の要旨
ページ3に含まれる内容の要旨
IMPORTANT INFORMATION Read prior to activation You have just purchased a sophisticated electro-optical device that emits invisible laser radiation. To operate it properly, please, read this manual carefully. NEVER direct laser beam at the eyes of people or animals NEVER aim the unit at the Sun or bright sources of light NEVER subject the unit to impacts NEVER transport the unit without the case NEVER disassemble the unit. This may be hazardous for you due to high voltage cur
ページ4に含まれる内容の要旨
TABLE OF CONTENTS 1. BRIEF DESCRIPTION............................................ 2 1.1 Principle of operation........................................... 2 1.2 Key Features ........................................................ 3 2. DEVICE APPEARANCE ........................................ 4 3. DELIVERY SET ...................................................... 6 3.1 Standard delivery set............................................ 6 4. SPECIFICATIONS .................................
ページ5に含まれる内容の要旨
CAREFULLY READ ALL THE INSTRUCTIONS BEFORE USING THE UNIT! FAILURE TO OBEY THE INSTRUCTIONS WILL VOID THE WARRANTY AND MAY CAUSE INJURY! 1. BRIEF DESCRIPTION LRM 1200 / 1500 / 1500SPD Laser Rangefinder Monocular (the unit) is an advanced laser range finder system that enables instant distance and speed (1500SPD modification only) measurement. The unit complies with CFR 21, Part 1040.10. An outstanding fully multi-coated optics coupled with an original circuitry design creates a
ページ6に含まれる内容の要旨
Key Features Distance is displayed in meters or yards Original digital circuitry allows ranging through most types of glass, bushes and other obstacles Three channel optical solution (optical, laser and receiver) provides high accuracy Two reticle shapes: -¦- or Target quality display indicator (1200 / 1500 modifications only) assures that results are reliable On-board memory keeps results of last 10 measurements, that can be recalled to the LCD The unit automatic
ページ7に含まれる内容の要旨
2. DEVICE APPEARANCE 6 7 5 1 4 8 3 2 Fig. 1. Front view 1 - Eyepiece 2 - Objective lens 3 - Laser emitter lens 4 - Receiver lens 5 - M (Mode) button 6 - A (Action) button 7 - Body of the device 8 - Rubber grip 4
ページ8に含まれる内容の要旨
11 9 1 12 10 Fig.2. Rear view 1 - Eyepiece 9 - Battery compartment cover 10 - Tripod socket 11- Identification imprint 12 - Classification imprint, shown below 5
ページ9に含まれる内容の要旨
3. DELIVERY SET Standard delivery set LRM 1200 / 1500 / 1500SPD is supplied in the following assembly: Qty LRM 1 9V Alkaline battery 1 Soft carrying case 1 Neck strap 1 Operation manual 1 Warranty card 1 6
ページ10に含まれる内容の要旨
4. SPECIFICATIONS Optics Magnification 7x Objective lens diameter 25 mm Exit pupil diameter 3.6 mm Field of view 8 Type of coating Fully multi-coated optics Range Finder Laser Class 1, eye safe, 905 nm Measuring range, LRM 1200 20 m – 1,200 m Measuring range, LRM 1500, 1500SPD 20 m – 1,500 m Accuracy 1.5 m Meters/Yards display Yes Last 10 readings recall Yes Reticle -¦- or Target quality indicator Yes 7
ページ11に含まれる内容の要旨
Speed Detector (LRM 1500SPD only) Measured speed range 5-400 km/h Accuracy ±2 km/h Power Battery 9V 'Low Battery' indicator Yes Environmental o o Operational temperature range -25 / +50 C (-13 / +122 F) o o Storage temperature range -45 / +65 C (-49 / +149 F) Mechanics Tripod thread ¼” x 20 Weight without battery 445 g Dimensions 127 mm x 125 mm x 60 mm 8
ページ12に含まれる内容の要旨
5. OPERATION INSTRUCTIONS 8 7 6 1 2 5 4 3 Fig. 3. Liquid Crystal Display as seen through the eyepiece 1 – Low battery indicator 2 – Reticle (either -¦- or ) 3 – Units of measurement 4 – Measurement result 5 – Target quality indicator 6 – Laser active indicator 7 – Setup mode indicator 8 – Ready mode indicator 9
ページ13に含まれる内容の要旨
Changing battery To install a battery: Slide the battery compartment cover down (9, Fig. 2) Install the battery observing polarity Don’t apply superfluous strength while pushing the battery inside the compartment. Close the compartment cover If the battery does not fit the compartment easily, it means that polarity was reversed To take a battery out: Slide the battery compartment cover down (9, Fig. 2) Shake the rangefinder gently towards the open end of the battery comp
ページ14に含まれる内容の要旨
Measuring procedure To start the measuring procedure, remove the lens cover. Look through the eyepiece (1, Fig. 1, 2) and adjust the focus by its rotating. When the Rangefinder is off the LCD is blank. To activate it press and hold A button (6, Fig. 1) for half a second. At start the unit comes into Ready to Measure mode indicated by the word ‘READY’ on the display visible through eyepiece. You may need to adjust the focus again so that both the display and distant objects are seen s
ページ15に含まれる内容の要旨
Target reflectivity depends on its color, surface finish, size, shape, position in relation to the laser beam, etc. Bright target colors are more reflective than darks. A polished surface is more reflective than a rough one. Larger targets reflect better than small ones. Ranging a target perpendicular to the laser beam provides better results than the one positioned under a sharp angle to the beam. Weather conditions that influence air transparency (rain, fog, snow, mist) reduce maximum
ページ16に含まれる内容の要旨
KMH/MPH: units of speed measurement: km/hour or miles/hour (3, Fig.3) (LRM 1500SPD only). Shape of the reticle: cross shape or rectangular shape (2, Fig.3). rEC1: Data Recall mode. It returns results of the last 10 measurements on the display. Measurement results are saved in on-board memory. When you enter the Data Recall mode, first measurement set number (display name: rEc 1) will start flashing. Pressing M button moves the unit along the list of measurement set numbers and measu
ページ17に含まれる内容の要旨
Additional display information Distance measuring procedure includes instant statistical processing of the package of single measuring sessions. If there is more than one measured target in the field of view, the embedded software estimates the most probable one by calculating the number of reflected pulses multiplied by the target statistical weight. This mechanism allows automatic mitigation of the influence of obstacles like rain, flakes, trees, wires and so on. Qualitative result
ページ18に含まれる内容の要旨
6. STORAGE AND MAINTENANCE The unit is a sophisticated precision optical instrument equipped with laser and electronics. Therefore, it should be handled with due care. Keep away from direct sunlight. Avoid impacts, jolts, dust, moisture, and sharp changes of temperature. o Do not use the device at temperatures higher than 50 C o (122 F). Prevent unit from direct sunlight Do not touch optical surfaces. Doing so may damage the anti-reflection coating. Clean optical surfaces
ページ19に含まれる内容の要旨
7. TROUBLESHOOTING The ranging does not work. The display is transparent. Check the charge of the battery. Replace it if it is weak. Black dots are visible on LCD. Liquid Crystal Display may have small black dots, scratches and other blemishes inherited from the manufacturing process. These flaws are strictly regulated by number, area and location and do not degrade the product's measurement capabilities. Range measurement cannot be obtained. Make sure that neither your hand nor finge
ページ20に含まれる内容の要旨
8. WARRANTY NEWCON warrants this product against defects in material and workmanship for one year from the date of the original purchase. Longer warranty is available, subject to the terms of the specific sales contract. Should your Newcon product prove to be defective during this period, please deliver the product securely packaged in its original container or an equivalent, along with the proof of the original purchase date to your Newcon Dealer. Newcon will repair (or at its option r
