ページ1に含まれる内容の要旨
10. QUALITY CERTIFICATE
The LRB 7X50 / LRB 7x50 SPD is suitable for use.
Production date ____________________________
Operation Manual
Serial number ______________________________
Quality Inspector signature _____________________
Purchase date ______________________________
Salesman _________________________________
Shop stamp LRB 7x50 /
LRB 7x50 SPD
LASER RANGE FINDER BINOCUL
ページ2に含まれる内容の要旨
9. CUSTOMER SUPPORT IMPORTANT INFORMATION Should you experience any difficulties with your Newcon OPTIK Read prior to activation product, consult the enclosed manual. If the problem remains unresolved, contact our customer support department at (416) 663- You have just purchased a complicated electronic device. To 6963 or Toll free at 1-877-398-6666. Our operating hours are operate it properly, please read this manual carefully. Here are 9am-5pm, Monday - Friday, Eastern St
ページ3に含まれる内容の要旨
8. WARRANTY Features of the LRB 7X50 Laser Range Finder Binocular NEWCON OPTIK warrants this product against defects in • Latest digital circuitry allows targeting through most types of material and workmanship for one year from the date of the glass original date of consumer's purchase, but no more than 18 • 'Last Target' measurement months from the date of manufacturing. Should your Newcon • Meters/Yards display product prove defective during this period, please bring the • La
ページ4に含まれる内容の要旨
BEFORE USE CAREFULLY READ ALL THE INSTRUCTIONS! 7. TROUBLE SHOOTING The range measuring mode does not work. FAILURE TO OBEY THE INSTRUCTIONS WILL VOID Press the Action Button again. THE WARRANTY! Check that the batteries are installed properly. Check the charge of the batteries. Replace if they are weak. 1. BRIEF DESCRIPTION How can I clear last reading before making next measurement? Direct the unit’s LCD reticle at the new target, press the Action LRB 7X50 (SPD) Laser
ページ5に含まれる内容の要旨
6. STORAGE AND MAINTENANCE INSTRUCTIONS. 2. APPEARANCE OF THE DEVICE Precautions: LRB 7X50 (SPD) is a sophisticated precision optical instrument equipped with electronics. Therefore, it 4 should be handled with due care. 1 6 • Keep your device away from direct sunlight, impact, dust, moisture, and sudden changes of temperature. • Do not touch the optical surfaces with fingers. Doing so 7 may damage the anti-reflection coating. • Avoid shocks and sharp jolts. • Cl
ページ6に含まれる内容の要旨
1 • TARGET REFLECTION MED - when the number of steady received reflected signals is in medium range and enough to make positive conclusion about the measured distance; Patent pending • TARGET REFLECTION HIGH - when the number of Newcon Optik steady received reflected signals is qualified to be enough to make reliable conclusion about the measured distance. Made in Canada The displayed statistical qualification of the reflected signal characterizes variation in expecte
ページ7に含まれる内容の要旨
CL - clear data function: upon pressing the Action button (6) 4. TECHNICAL CHARACTERISTICS (fig. 1) the entire data on all previous measurements will be erased. 1. Optics NOTE: After changing a battery the recall stack should be Observation Binocular cleared by exercising the CL mode. Magnification, x 7 OVER 100 – allows to ignore targets closer than 100m. Useful Objective Lens, mm 50 when looking through bush. Exit Pupil Diameter, mm 7.1 Please note: this is an optiona
ページ8に含まれる内容の要旨
- REC 0 will show instead of REC10 2. Range Finder - If a position is empty then 4 dashes (----) will be displayed Type Class 1 eye safe, 905nm - After REC 0 the demonstration will restart with REC 1, Measuring Range, m 20-1,512 REC2, and so on Accuracy, m ±1 ± 0.1% 2) If the last measurement was that of speed, then the speed will Resolution, m 1 show in Measurement time, sec <1 REC1; the distance of the vehicle will show in REC2 and so on. Meters/Yards display
ページ9に含まれる内容の要旨
5.2.6 Mode Selection State 5. OPERATION INSTRUCTIONS Correct Order of Modes Liquid Crystal Display (LCD) LRB 7x50 LRB 7x50 SPD Y MPH M KMH 6 + + 1 1 REC Y CLR M 3 SELFTEST 2 5 REC CLR 2 1) REC1 shows the value of the last measurement, REC 2 the previous measurement and so on. b. Mode selection state Pressing MODE button (5) (fig. 1) when the System is in 4 3 READY mode brings the System to the Mode selecting state. Pressing the Mode
ページ10に含まれる内容の要旨
Pressing Action button (6) (fig. 1) at this point triggers a distance 5.1. Preparing the Device for Operation measuring session, and the result will be displayed in numerical form (4) (fig. 3) (if measurement is unsuccessful then four dashes • Unbolt a screw and open battery compartment cover at the ‘----‘ will appear in the numerical area). Please note that the target bottom of the device. must be over 20m away. • Insert one 9V battery (sold separately) into the battery compa
