ページ1に含まれる内容の要旨
VHF Wireless Microphone System
™
DigiTRU Diversity
ページ2に含まれる内容の要旨
CONTENTS CONTENTS ....................................................................................................2 INTRODUCTION .............................................................................................2 USING THIS MANUAL .....................................................................................2 SYSTEM FEATURES ..........................................................................................3 ENCORE II RECEIVER ......................................
ページ3に含まれる内容の要旨
SYSTEM FEATURES • A vailable on selected frequencies in the VHF high band (171‑216 MHz) for interference‑free, longrange per ‑ formance • Proprietar y companding circuitr y for an industr y-best 120dB Dynamic Range, and the clearest, most natural sound available • Operating Range: Up to 250 feet typical (depending on site conditions)— up to 500+ feet line- of-sight • Noise-free transmitter ON-OFF operation ENCORE II RECEIVER • Half-rack receiver design with retractable front pa
ページ4に含まれる内容の要旨
ENCORE II RECEIVER 1. Rackmounting the Receiver There are two options available for rackmounting the Encore II receiver: singly or sideby ‑ ‑side with another Encore Series receiver. a. Single mounting: Remove the receiver SIDE MOUNT CLIP (1) from each side of the receiver (as shown) and slide in the optional ERM-12 RACK EARS (9). b. Side-by-side double mounting: After removing the SIDE MOUNT CLIPS (1) from both Encore receivers, join the two receivers with the EJC-2 JOINING CLIP (10) and
ページ5に含まれる内容の要旨
5. Connecting the Audio Output The Encore II receiver provides both a fixed mic level BALANCED AUDIO OUTPUT XLR (14) and an adjustable line level UNBALANCED AUDIO OUTPUT 1/4” JACK (13). The level from the UNBALANCED OUTPUT is controlled by the rear panel VOLUME CONTROL (6). (Note: As when making any connection, make sure the amplifier or mixing board volume is at the minimum level before plugging in the receiver to avoid possible sound system damage. Also make sure that the phantom power
ページ6に含まれる内容の要旨
16 16 AF 7 RF POWER A B 8 3 4 5 12-15V VOLUME MUTE UNBALANCED OUT DC INPUT BALANCED OUT 13 11 6 14 2 15 1 9 9 1 12 10 12 6
ページ7に含まれる内容の要旨
WHT HANDHELD MICROPHONE TRANSMITTER 1. Unscrew the BATTERY COMPARTMENT COVER (17) and remove, exposing the BATTERY HOLDER (18). Insert a fresh 9V ALKALINE BATTERY (19), observing the correct polarity as marked, and screw the cover back on to the microphone. Make sure the cover is screwed on completely. A fresh alkaline battery can last up to 16 hours in use, but in order to ensure optimum performance, it is recommended that you replace the batter y after ever y 10 hours of use. 2. Turn on t
ページ8に含まれる内容の要旨
21 20 18 19 17 8
ページ9に含まれる内容の要旨
WLT LAVALIER/LAPEL OR HEADWORN MICROPHONE BODYPACK TRANSMITTER 1. Snap open the BATTERY COMPARTMENT (22) and insert a fresh 9V BATTERY (23), observing the correct polarity. Close the compartment. 2. The WLT is provided with a 3.5 mm LOCKING JACK (24) for connecting the microphone. Plug in either the LAVALIER/LAPEL (25) or the HEADWORN MICROPHONE (26), as supplied. To secure the connection, turn the metal slip ring on the plug clockwise to thread it on to the jack. T o unplug, reverse the
ページ10に含まれる内容の要旨
24 29 28 27 22 25 26 22 Opening Battery Compartment 23 10 BAT HI LOW MIC OFF/STANDBY/ON
ページ11に含まれる内容の要旨
WGT INSTRUMENT BODYPACK TRANSMITTER 1. Snap open the BATTERY COMPARTMENT (30) and insert a fresh 9V BATTERY (31), observing the correct polarity. Close the compartment. The WGT is provided with a 3.5 mm LOCKING JACK (32) for connecting the INSTRUMENT CABLE (35). To secure the connection, turn the metal slip ring on the plug clockwise to thread it on to the jack. T o unplug, reverse the process. Slip the transmitter into a pocket or clip on to your clothes or instrument strap. (Note: As th
ページ12に含まれる内容の要旨
35 34 33 32 30 30 Opening Battery Compartment 31 12
ページ13に含まれる内容の要旨
SPECIFICATIONS ENCORE II OVERALL SYSTEM PERFORMANCE ™ Reception Mode DigiTRU Diversity Controls Power ON/OFF, volume control, mute control Connectors Balanced XLR and unbalanced adjustable 1/4” audio out jacks, 2.1 mm barrel-type DC input jack LED Indicators Power ON, 5‑LED RF & AF level displays, A/B Diversity Dimensions (Max.) 1.75” x 7.5” x 8.1” (4.4 x 19 x 20.7 cm) Weight 1.6 lbs (.73 kg) Power Requirements 12V @ 400mA, nominal, AC/DC adapter supplied Ante
ページ14に含まれる内容の要旨
SERVICE INFORMATION In the U.S. If you are experiencing operational problems with your system, please refer to the Support page at www.nady.com for assistance. Should your wireless system require ser vice, please contact the Nady Ser vice Depar tment at (510) 652‑2411 to obtain a Return Authorization (R/A) Number and service quote (if out of warranty). Make sure the R/A Number is clearly marked on the outside of the package that you are returning. If your unit is out of warranty, please en
ページ15に含まれる内容の要旨
ONE-YEAR LIMITED WARRANTY Nady Systems, Inc. warrants to the original consumer purchaser that the unit is free from any defects in material or workmanship for a period of one year from the date of original retail purchase. If any such defect is discovered within the warranty period, Nady Systems, Inc. will repair or replace the unit free of charge, subject to verification of the defect or malfunction upon return to Nady Systems. Please do not return your Nady product to the store where it w
ページ16に含まれる内容の要旨
Nady W ireless Systems are type accepted under FCC rules par ts 90, 74 and 15. The device complies with RSS-210 of Industr y & Science Canada. Operation is subject to the following two conditions: (1) this device may not cause har mful interference and (2) this device must accept any interference received, including interference that may cause undesired operation. 6701 Shellmound Street | Emeryville, CA USA 94608 | | T 510.652.2411 F 510.652.5075 www.nady.com
