ページ1に含まれる内容の要旨
1383
Today’s Weather 24 Hour Forecaster
Instruction Manual
Get actual current temperatures and predict the weather
conditions for the next 24 hours as well as your local television
weatherperson! Taylor uses the temperature and changes in
relative humidity levels to forecast the upcoming day. Plan the
®
day with confidence with Taylor Today’s Weather.
Please read this instruction manual carefully before use and
keep these instructions handy.
To Power and Set Up the Weather Forecaster
1
Bat
ページ2に含まれる内容の要旨
Set Current Weather Conditions 2 1. After battery installation, the current weather icon flashes. 2. Press “Up” or “Down” to select the weather icon you believe most closely reflects the current conditions in your area. (Partly Cloudy is the default setting). 3. Press “Time/Date” to select the displayed weather icon. The icon stops flashing. Icon flashes during setup, then steady when set 2
ページ3に含まれる内容の要旨
4.The selected weather icon appears on all screens. (The temperature and forecast readings update after remote sensor is added.) 3 Install Batteries into Remote Sensor *Important: Install the remote sensor batteries after installing the base unit batteries for proper signal connection. Remote sensor – use 2 AAA lithium batteries (not included). Remove the screws from the battery compartment on the back of the remote (take care not to misplace the screws). Install the batteries acco
ページ4に含まれる内容の要旨
Set Up Remote Sensor 4 1. After installing the batteries into the base unit and the remote sensor, place the units close together for best setup connection. 2. Press the “SYNC” button on the back of the base unit to send a transmission signal to the remote sensor. Allow a few minutes for a connection as the icon flashes and the temperature digits show dashes. When connected the icon disappears. icon flashes while transmitting, disappears after connection to remote
ページ5に含まれる内容の要旨
Only the current temperature will update during first 6 hours. Temperature forecasts and weather icons stay identical while analyzing 1st forecast. 5. After the first 6 hours, when the units begin to forecast weather conditions, all temperature and weather screens will update with new forecasts. Temperature and Weather forecasts update 6. The remote sensor will automatically transmit weather condi- tions to the base unit. • Indoor temperature readings will update approximately every 30 seco
ページ6に含まれる内容の要旨
To Set Clock and Date 5 1. Press and hold “TIME/DATE” for 2 seconds, then release. 2. Press “UP” or “DOWN” to change the hours. Press “TIME/DATE”. 3. Press “UP” or “DOWN” to change the minutes. Press “TIME/DATE”. 4. Press “UP” or “DOWN” to switch between a 12 or 24 hour clock. Press “TIME/DATE”. 5. Press “UP” or “DOWN” to change the year. Press “TIME/DATE”. 6. Press “UP” or “DOWN” to change the month. Press “TIME/DATE”. 7. Press “UP” or “DOWN” to change the date. Press “TIME/DATE”.
ページ7に含まれる内容の要旨
Additional Features 7 °C/°F Selection Press the “C/F” button on the back of the base unit to switch between Fahrenheit and Celsius temperatures. Backlight Press the Backlight button on the top of the base unit. The LCD screen will light up for approximately 5 seconds. Low Battery Warning Base unit – replace both batteries when the “ ” icon appears on the right side of the screen. Remote sensor – replace both batteries when the “ ” icon appears on the left side of the screen.
ページ8に含まれる内容の要旨
8 Tips (continued) Important: Though the remote unit is weather resistant, it should be placed away from direct sunlight, rain, snow and should never be sub- merged in water. Note: The effective range is greatly affected by the building materials and where the base and remote units are positioned. Try various set ups for the best results. Check to make sure the transmission path is clear of obstacles and interference. Shorten the distance between base and remote units when necessary. Pla
ページ9に含まれる内容の要旨
Problem Solving 9 1. If the LCD readout is faint, replace the batteries. 2. If outdoor temperature does not display on the base unit: a) Press the “SYNC” button to trigger a signal from the base to the remote; b) Relocate remote sensor if it is obstructed from weather condi- tions or in contact with an object that might affect tempera- ture readings (hot metal object, snow, etc.) c) Remove and reinstall all batteries, using new fully charged batteries; d) Repeat set-up procedures; e) Pla
ページ10に含まれる内容の要旨
Transmission Information The remote sensor sends temperature and weather condition information to the base unit. After installing batteries into both units, allow 6 hours to analyze weather conditions and report forecasts. Weather readings will update as follows: • Current temperature updates approximately every 1 minute. • Temperature and weather forecasts update every 6 hours during the first 24 hours of operation after battery installation. • After 24 hours, updates occur every 1 ho
ページ11に含まれる内容の要旨
1 1 Precautions 1. Always read the instruction manual before operating this product. 2. The base unit is intended for indoor use only. It is not sealed against moisture and could be damaged if used outdoors. 3. Do not immerse the base unit in water. If you spill liquid on it, dry immediately with a soft, lint-free cloth. 4. The remote sensor is weather resistant but not waterproof and should never be submerged in water. It should be placed away from direct sunlight, rain, and snow. 5. D
ページ12に含まれる内容の要旨
1 2 Specifications Range of temperature measurement: Base unit (indoor only): 14°F to 122°F (-10°C to 50°C) Remote sensor: With Lithium batteries: -4°F to 158°F (-20°C to 70°C) With Alkaline batteries: 14°F to 122°F (-10°C to 50°C) Resolution: 1° for temperature Outdoor Humidity: 20% - 99% RH Power: Base unit – 2 AAA alkaline batteries Remote sensor – 2 AAA lithium batteries (recommended for wider temperature range) 5 weather forecast icons: Sunny, Partly Cloudy, Cloudy, Rain, Snow 5 f
