ページ1に含まれる内容の要旨
INSTALLATION/OPERATION MANUAL
MIRATRON WIRELESS
REMOTE CONTROL RADIO
MAYCO MODEL C30HDG
Revision #0 (08/19/09)
THIS MANUAL MUST ACCOMPANY
THE EQUIPMENT AT ALL TIMES.
ページ2に含まれる内容の要旨
TABLE OF CONTENTS Warranty ............................. 3 Overview ............................ 4 Specifi cations .................... 5 Care And Handling ............. 6 Receiver Installation ......... 7-8 Cable Installation .............. 9 Wiring Diagram................... 10 Transmitter/Receiver ......... 11-12 Troubleshooting ................. 13 System Wiring Diagram ..... 14 PAGE 2 — INSTALLATION OPERATION MANUAL — REV. #0 (08/19/09)
ページ3に含まれる内容の要旨
WARRANTY LIMITED ONE YEAR WARRANTY Miratron Incorporated, hearafter referred to as Miratron, is providing this warranty in lieu of all other express or implied warranties, including any warranty of merchantability or fi tness for a particular purpose. This warranty is buyer’s exclusive remedy for all claims against Miratron. Miratron shall not be liable for any consequential or incidental damages. Miratron’s total liability for all contracts, negligence, or other claims shall be limited to t
ページ4に含まれる内容の要旨
OVERVIEW ALWAYS read manual before attempting to operate the equipment. Failure not to read manual could cause severe equipment damage and or damage to the receiver and transmitter. Make sure work area is safe to operate radio control receiver and transmitter. This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including int
ページ5に含まれる内容の要旨
SPECIFICATIONS Table 1. Specifi cations Miratron Model Number: RX4 Radio Control Receiver CMD16-0135 ~ (MQ P/N EM98215) General: Power Requirements 12-24VDC, 500mA max Radio: Frequency Standard 902-928 MHz, FHSS, ISM Band Frequecy Control Direct FM FCC ID OUR9XCITE (Standard) Receiver Sensitivity -106 dBM Transmitter: CMD16-0135 ~ (MQ P/N EM98215) Range 300 ft. (91.44 meters) Line of Sight (Standard) Battery Type 1.5 Volt “AA” Alkaline (4) Standby, 80 hrs. — Transmitt, 12-16 hrs. Battery Life (
ページ6に含まれる内容の要旨
CARE AND HANDLING Transmitter: Clean transmitter gently with a damp cloth. DO NOT immerse transmitter in water, or spray with hose. DO NOT store outside. DO NOT drop transmitter or otherwise subject transmitter to physical shock. DO NOT expose transmitter to extreme temperatures. DO NOT open transmitter enclosure. Transmitter contains no serviceable parts. Receiver: Remove receiver from machine prior to welding on machine DO NOT paint electrical connector. Use only factory provi
ページ7に含まれる内容の要旨
RECEIVER INSTALLATION Parts: Make sure all parts are accounted for before performing the installation. The following parts are included with the kit: Radio Transmitter Radio Receiver Spiral Antenna with associated mounting hardware Coaxial Antenna Cable Data /Power Cable (7-wire) Remote Control Cable Battery Disconnection 1. Disconnect the negative terminal of the battery cable from the battery. Ant enna Mounting 1. Drill a 3/4” hole into the hood on the C30HDG as shown in Figure 1.
ページ8に含まれる内容の要旨
R RX4 X4 RA RA R RE D D EIIO C C OEIVE EC C I V ONTR O E N R RTRO OL L M MIRA IRATRON TRON T L RX4 RX4 RADIO RA RECEIVER RD EIC OECONTROL C IV O E N R RO M MIRA IRAT TRON RON RECEIVER INSTALLATION Radio Control Receiver Mounting 1. Drill two 1/4” holes into the control box support panel on the C30HDG as shown in Figure 1. 2. After both holes have been drilled, deburr each hole opening. 3. Using a 1/4-20 x 1-1/4 bolt (2), 1/4 lock washer (2), 1/4 fl at washer (2) and 1/4 nut (2), mount the rad
ページ9に含まれる内容の要旨
CABLE INSTALLATION Control Box Removal 1. Using a 7/16 socket remove the mounting bolts (3) that secure the control box to the support bracket. 2. Once the bolts have been removed, fl ip the panel downward to gain access to the connection points. Data Cable Connections 1. Wire data cable into control box as shown in Figure 2. 2. Crimp a 16-14 (3/16”) terminal ring onto the RED wire labeled BATT+. Connect this end of the wire to the +12VDC terminal strip, pin 2. 3. Crimp a #16-14 (3/16”) termi
ページ10に含まれる内容の要旨
CHECK HOOD OPEN ENGINE ENGINE HOURS PUMPING CONTROL REMOTE OUTLET REMOTE OFF PUMP ON ON T H R O T HIGH LOW T L E IGNITION SWITCH OFF ON START EMERGENCY STOP WIRING DIAGRAM REDORPINK 12-PIN DATA CABLE SPLICE
ページ11に含まれる内容の要旨
TRANSMITTER/RECEIVER The defi nitions below describe the controls and functions of the Miratron Transmitter and Radio Control Receiver. Transmitter 1. Power On Switch — Place this switch in the ON position to turn on the transmitter. Be sure to place this switch in the OFF position when the system is not in use. 2. Status LED Indicator — Status LED blinks to indicate transmitter is ON and active. LED will double-blink when battery strength is low. 3. E-STOP Switch — When activated will cause
ページ12に含まれる内容の要旨
RX4 RADIO CONTROL RECEIVER MIRATRON ENGINE PUMP INCREASE ON OFF DECREASE TRANSMITTER/RECEIVER Functional Test Perform the functional test procedure below to test the remote control radio system.. 1. Start the engine as outlined on the operator’s manual. 2. Place the transmitter power ON/OFF switch in the ON position. 3. Place the pumping control switch on the control box in the REMOTE ON position. 4. Toggle the engine speed switch back and forth. Verify that engine speed increases and decreas
ページ13に含まれる内容の要旨
TROUBLESHOOTING Table 2. Troubleshooting Symptom Possible Problem Solution Transmitter does not LED status indicator not Turn transmitter power function at all fl ashing. switch ON. Weak dead battery, replace batteries. Check orientation of batteries. Make sure transmitter has LED indicator not lit when be matched (paired) to power ON/OFF switch is receiver. pressed. Receiver is not powered up. Transmitter range is poor LED indicator not lit when Weak dead battery, replace power ON/OFF
ページ14に含まれる内容の要旨
SYSTEM WIRING DIAGRAM Figure 4. System Wiring Diagram PAGE 14 — INSTALLATION OPERATION MANUAL — REV. #0 (08/19/09)
ページ15に含まれる内容の要旨
NOTE PAGE INSTALLATION/OPERATION MANUAL — REV. #0 (08/19/09) — PAGE 15
ページ16に含まれる内容の要旨
INSTALLATION/OPERATION MANUAL HERE’S HOW TO GET HELP PLEASE HAVE THE MODEL AND SERIAL NUMBER ON-HAND WHEN CALLING UNITED STATES Multiquip Corporate Offi ce MQ Parts Department 18910 Wilmington Ave. Tel. (800) 421-1244 800-427-1244 Fax: 800-672-7877 Carson, CA 90746 Fax (800) 537-3927 310-537-3700 Fax: 310-637-3284 Contact: mq@multiquip.com Mayco Parts Warranty Department 800-306-2926 Fax: 800-672-7877 800-421-1244, Ext. 279 Fax: 310-537-1173 310-537-3700 Fax: 310-637-3284 310-537-3700, Ext. 279 S