ページ1に含まれる内容の要旨
Pub. 988-0158-031
www.eaglesonar.com
EVR-100
VHF Radio
Operation Instructions
ページ2に含まれる内容の要旨
Copyright © 2007 Navico All rights reserved. Eagle® is a registered trademark of Navico No part of this manual may be copied, reproduced, republished, transmitted or distributed for any purpose, without prior written consent of Eagle Electronics. Any unauthorized commercial distribution of this manual is strictly prohibited. Eagle Electronics may find it necessary to change or end our policies, regulations, and special offers at any time. We reserve the right to do so without notice. All fe
ページ3に含まれる内容の要旨
Table of Contents Introduction ............................................................................................................................................. 4 Installation .............................................................................................................................................. 5 Display ................................................................................................................................................... 11 Basic Op
ページ4に含まれる内容の要旨
: Introduction Congratulations on your purchase of an Eagle EVR-100 marine band VHF radio. Designed for international operation, allows you to transmit and receive on all international channels in the VHF marine band, as assigned by the International Union (ITU). The EVR-100 is approved with commercial-grade standards to give you clear, reliable communication. NOTE: According to WEEE regulations, the user should not dispose the product when damaged, but rather send it back to Eagle for dis
ページ5に含まれる内容の要旨
: Installation This Eagle radio allows you to make a maritime distress call to facilitate search and rescue. To be effective as a safety device, this radio must be used only within the geographic range of a shore-based VHF marine Channel 16 distress and safety watch system. The geographic range may vary but under normal conditions is approximately 20 nautical miles. Installation Options There are two ways to install the radio. You can choose: • a deck or overhead mounted gimbal installation.
ページ6に含まれる内容の要旨
Checklist The following items should be supplied in the box. Check before starting the installation and con- tact your dealer if an item is missing. NOTE: An antenna is NOT provided. Consult your Eagle dealer for advice if necessary. 1. Mounting gimbal for the VHF radio 13. Two spring washers for the microphone bulkhead mount 2. Power supply cable with inbuilt 3 Amp fuse 14. Two plain washers for the microphone bulkhead mount 3. External speaker connection cable with white (+) wire a
ページ7に含まれる内容の要旨
Gimbal Installation 1. Hold the mounting gimbal at the chosen location and use a soft pencil to mark the screw hole positions onto the mounting surface. 2. If you can’t reach behind the mounting surface to attach the nuts, use the self-tapping screws instead of the flat screws shown in the picture. If you’re drilling into fiberglass, use a drill bit smaller than 3/16” (5mm) to drill the pilot holes. Otherwise, drill the four screw holes where marked, using a 3/16” (5mm) drill bit. Drill com-
ページ8に含まれる内容の要旨
5. Use the two short M5x10 screws to screw the mounting brackets to the sides of the radio. 6. Screw each M5x32 screw through the screw hole in the mounting bracket, then attach the stopper. If your bulkhead exceeds 0.51” (13mm), the stopper can be discarded if necessary. 7. Tighten the M5x32 screws until the radio is held firmly against the rear of the bulkhead. Install the Microphone Bulkhead Mount 1. Hold the microphone bulkhead mount at the chosen location and use a soft pencil to ma
ページ9に含まれる内容の要旨
Connect the Radio Cables The connectors are on the rear of the base unit, as follows: 1. External Speaker connector. Plug the external speaker cable jack into the connector BEFORE powering on the radio. Use a 4 Ohm 4 Watt external speaker. 2. RED Power wire. Connect this to the POSITIVE (+) battery terminal. Check that a 3 Amp fuse is installed on this power cable close to the battery. 3. BLACK Power wire. Connect this to the NEGATIVE (-) battery terminal. 4. ANT. A radio antenna is not supp
ページ10に含まれる内容の要旨
The Completed Installation External speaker VHF Antenna External speaker connection cable Antenna connection cable BLACK Fuse power on RED cable power cable Battery Base unit with microphone* * Actual model may differ from that shown 10 EAGLE EVR-100 Operation Instructions
ページ11に含まれる内容の要旨
Display LCD symbols and Meanings Symbol Meaning TX Transmitting. HI LO Transmission power. High (HI) 7W or Low (LO) 1W. BUSY Receiver busy with an incoming signal. WX Weather channel. WX ALT Weather Alert. Alarm beeps will sound. PRI Priority channel is selected. SCAN Scanning channels. DW Dual Watch mode. ALL ALL channels scan mode. C1 C2 C3 Shows which of the 3 favourite channels, if any, are selected, otherwise blank. (small) (large) Channel selected. UIC Selected Channel ba
ページ12に含まれる内容の要旨
Basic Operation and Key Functions Key Function VOL/PWR Volume and Power. Turn clockwise to power on. Continue to turn until a comfortable volume is reached. VOL/PWR will also adjust the settings of an external speaker, if connected SQL Squelch or Threshold Level. Sets the threshold level for the minimum receiver signal. Turn fully counterclockwise until random noise is heard, then turn slowly clockwise until the random noise disappears. Make another 1/4 turn clockwise for best reception in
ページ13に含まれる内容の要旨
To scan only one of your favourite channels, press 3CH then immediately press and release SCAN. If you want to scan all three favourite channels, press 3CH then immediately press and hold SCAN. To add a favourite channel for the first time, select that channel then hold 3CH to store it in the CH1 location. Repeat the procedure to store two more favourite channels in the CH2 and CH3 locations respectively. If you try and add another favourite channel it will overwrite the existing CH1.
ページ14に含まれる内容の要旨
Radio Operation Turning Your Radio On/Off Rotate VOL/PWR knob to turn the radio on or off. Rotate to adjust the volume to a comfortable level. Adjusting Squelch Squelch is used to eliminate static and background noise and allows for silent operation of your radio until a transmission is received. If the squelch is too high, only the strongest transmissions can be heard, and when too low, intermittent static and noise are heard. To set Squelch: 1. Turn SQL knob fully counter-clockwise. You
ページ15に含まれる内容の要旨
Scanning Features Your radio is equipped with 2 types of scan options: All Scan, 3CH Scan (Favourite Channel Scan). If there are no channels added as favourite channels, the default is All Scan. This function automatically searches for transmissions on the channel being scanned. If a signal is received, the scan stops on the receiving channel as long as it is present and the SCAN indicator flashes. If the signal is lost for 3 seconds, the radio resumes scanning. All Scan Press and hold th
ページ16に含まれる内容の要旨
NOAA Weather Channels To receive a NOAA (National Oceanic and Atmospheric Administration) weather channel, press the WX key. The transceiver will go to the last selected weather channel. Press the + CH - keys to scroll through the available WX channels. To exit from the NOAA weather channels, press the WX key to terminate WX mode and return to the previous working channel, or press 16/9 to access the priority channels. NOAA Weather Alert In the event of extreme weather disturbances, such as s
ページ17に含まれる内容の要旨
Appendix A - Technical Specifications GENERAL Power Supply: 13.8V DC. Current drain: Transmit 1.5 A at 7 W Tx / 0.6A at 1W Tx Receive Less than 250mA in standby Useable channels: International, USA, Canada, Weather (country specific) Mode: 16K0G3E (FM) PHYSICAL LCD display (viewing): 41(H) x 53(W) mm Backlight control: Yes (On/Off ) Antenna connector: SO-239 (50 ohm) Temperature Range: -17ºC to +50ºC Waterproof: JIS-7 Dimensions: 161(W) x 75(H) x 147(D) mm - without bracket Weight: 0.87kg with
ページ18に含まれる内容の要旨
Appendix B - Troubleshooting 1. The transceiver will not power up. A fuse may have blown OR there is no voltage getting to the transceiver. a) Check the power cable for cuts, breaks, or squashed sections. b) After checking the wiring, replace the 3 Amp fuse (1 spare fuse is supplied). c) Check the battery voltage. This must be greater than 10.5V. 2. The transceiver blows the fuse when the power is switched on. The power wires may have been reversed. a) Check that the red wire is conn
ページ19に含まれる内容の要旨
Appendix C - Frequency Charts International Channel Chart CH TX RX MODE TRAFFIC TYPE SHIP SHIP REMARK (MHz) (MHz) TO TO SHIP SHORE 01 156.050 160.650 D Public Correspondence No Yes 02 156.100 160.700 D Public Correspondence No Yes 03 156.150 160.750 D Public Correspondence No Yes 04 156.200 160.800 D Port Operations No Yes 05 156.250 160.850 D Port Operations, Selected VTS Areas No Yes 06 156.300 156.300 S Inter-ship Safety Yes No 07 156.350 160.950 D Port Operatio
ページ20に含まれる内容の要旨
66 156.325 160.925 D Port Operations No Yes 67 156.375 156.375 S Commercial, bridge-to-bridge Yes No 68 156.425 156.425 S Boat Operations, Recreational Yes No 69 156.475 156.475 S Port Operations Yes Yes 2 70 156.525 156.525 Digital Selective Calling - DSC ------ ------ 71 156.575 156.575 S Port Operations Yes Yes 72 156.625 156.625 S Inter-ship Yes No 73 156.675 156.675 S Port Operations Yes Yes 74 156.725 156.725 S Port Operations Yes Yes 77 156.875 156.875 S Inter-
