ページ1に含まれる内容の要旨
Installation and operation manual
Part Number 3-9008-504, rev. K
October, 2013
TM
Daniel Series 1500 turbine meter
3" thru 18" sizes
ページ2に含まれる内容の要旨
ページ3に含まれる内容の要旨
Safety signal words and symbols Pay special attention to the following signal words, safety alert symbols and statements: Safety alert symbol This is a safety alert symbol. It is used to alert you to potential physical injury hazards. Obey all safety messages that follow this symbol to avoid possible injury or death. Indicates a hazardous situation which, if not avoided, will result in death or serious injury. Warning indicates a hazardous situation which, if not avoided, could result in de
ページ4に含まれる内容の要旨
ページ5に含まれる内容の要旨
Important safety instructions Daniel Measurement and Control, Inc. (Daniel) designs, manufactures and tests products to function within specific conditions. Because these products are sophisticated technical instruments, it is important that the owner and operation personnel must strictly adhere both to the information printed on the product and to all instructions provided in this manual prior to installation, operation, and maintenance. Daniel also urges you to integrate this manual into your
ページ6に含まれる内容の要旨
Product operation personnel: • To prevent personal injury, personnel must follow all instructions of this manual prior to and during operation of the product. Follow all warnings, cautions, and notices marked on, and supplied with, this product. • Verify that this is the correct instruction manual for your Daniel product. If this is not the correct documentation, contact Daniel at 1-713-827-6314. You may also download the correct manual from: http://www.daniel.com • Read and understand all inst
ページ7に含まれる内容の要旨
Notice THE CONTENTS OF THIS PUBLICATION ARE PRESENTED FOR INFORMATIONAL PURPOSES ONLY, AND WHILE EVERY EFFORT HAS BEEN MADE TO ENSURE THEIR ACCURACY, THEY ARE NOT TO BE CONSTRUED AS WARRANTIES OR GUARANTEES, EXPRESSED OR IMPLIED, REGARDING THE PRODUCTS OR SERVICES DESCRIBED HEREIN OR THEIR USE OR APPLICABILITY. ALL SALES ARE GOVERNED BY DANIEL’S TERMS AND CONDITIONS, WHICH ARE AVAILABLE UPON REQUEST. WE RESERVE THE RIGHT TO MODIFY OR IMPROVE THE DESIGNS OR SPECIFICATIONS OF SUCH PRODUCTS AT ANY
ページ8に含まれる内容の要旨
Warranty and limitation of liability 1. LIMITED WARRANTY: Subject to the limitations contained in Section 2 herein, Daniel Measurement & Control, Inc. (“Daniel”) warrants that the licensed firmware embodied in the Goods will execute the programming instructions provided by Daniel, and that the Goods manufactured by Daniel will be free from defects in materials or workmanship under normal use and care and Services will be performed by trained personnel using proper equipment and instrumentation
ページ9に含まれる内容の要旨
DANIEL™ SERIES 1500 TURBINE METER OCT 2013 TABLE OF CONTENTS 1.0 INTRODUCTION .................................................... 1-1 1.1 General ........................................................ 1-1 1.2 Description ..................................................... 1-1 2.0 SPECIFICATIONS ................................................... 2-1 3.0 INSTALLATION ..................................................... 3-1 3.1 General ........................................................
ページ10に含まれる内容の要旨
OCT 2013 DANIEL™ SERIES 1500 TURBINE METER This page intentionally left blank. ii TABLE OF CONTENTS
ページ11に含まれる内容の要旨
DANIEL™ SERIES 1500 TURBINE METER OCT 2013 Figures 3-1 Typical Installation .................................................... 3-2 3-2 UMB Wiring ......................................................... 3-7 7-1 UMB Assembly - All Sizes .............................................. 7-2 7-2 High Temperature UMB Assembly ........................................ 7-4 7-3 Meter Assembly - Sizes 3" through 18" Uni-Directional ....................... 7-6 7-4 Meter Assembly - Sizes 4" through 8" Bi-D
ページ12に含まれる内容の要旨
OCT 2013 DANIEL™ SERIES 1500 TURBINE METER This page intentionally left blank. iv TABLE OF CONTENTS
ページ13に含まれる内容の要旨
DANIEL™ SERIES 1500 TURBINE METER OCT 2013 1.0 INTRODUCTION 1.1 General This manual is designed to assist in the installation and operation of the Daniel™ Series 1500 Turbine Meter. To assure proper installation and startup it is important to read this manual in its entirety. 1.2 Description The Series 1500 Turbine Flowmeter is a volumetric flow metering and transmitting device used extensively in the petroleum industry for the accurate measurement of hydrocarbon and other related process fluids
ページ14に含まれる内容の要旨
OCT 2013 DANIEL™ SERIES 1500 TURBINE METER This page intentionally left blank. 1-2 INTRODUCTION
ページ15に含まれる内容の要旨
DANIEL™ SERIES 1500 TURBINE METER OCT 2013 2.0 SPECIFICATIONS This meter is designed for use within the guidelines of API Standards, Chapter 5.3, formerly Standard 2534 (The Measurement of Liquid Hydrocarbons by Turbine Meter Systems) and the test procedures of API Standards, Chapter 4 (Prover Systems). PERSONAL INJURY AND/OR EQUIPMENT DAMAGE Do not exceed specifications listed below. Failure to heed this warning could result in serious injury and/or damage to the equipment. Approvals: Electrica
ページ16に含まれる内容の要旨
OCT 2013 DANIEL™ SERIES 1500 TURBINE METER INMETRO certification Certification number and marking Applicable norms ABNT NBR IEC 60079-0:2008 ABNT NBR IEC 60079-1:2009 Temperature range -40 /C # to # +60 /C Conditions for safe use (X) - The joint between the Universal Mounting Box cover and housing is a flat joint and has a flame path of 9,52 mm in length and clearance of less than 0,0381 mm. - The joint between the Universal Mounting Box housing and Sensor housing is a spigot joint which has
ページ17に含まれる内容の要旨
DANIEL™ SERIES 1500 TURBINE METER OCT 2013 Pressure/Temperature Carbon Steel Stainless Steel 600 ANSI / -20 to 100°F (-29° to 82°C) 1480 psig WP 1440 psig WP 600# ANSI / 180°F (82°C) 1376 psig WP 1248 psig WP 600# ANSI / 400°F (204°C) 1270 psig WP 995 psig WP 900# ANSI / -20 to 100°F (-29° to 82°C) 2220 psig WP 2160 psig WP 900# ANSI / 180°F (82°C) 2064 psig WP 1872 psig WP 900# ANSI / 400°F (204°C) 1900 psig WP 1490 psig WP 1500# ANSI / -20° to 100°F (-29° to 82°C) 3705 psig WP 3600 psig WP 150
ページ18に含まれる内容の要旨
OCT 2013 DANIEL™ SERIES 1500 TURBINE METER Meter Performance Linearity ± 0.15% (Linearity options of ± 0.1% and ± 0.07% available on certain sizes). Repeatability ± 0.02% at any point throughout the extended minimum to extended maximum flow range. Pressure Drop At maximum flow of normal flow range on water 4 psi. Pressure Range ANSI 150 - 1500 # depending upon size Viscosity and Specific Gravity Low specific gravities or high velocities will reduce flow range of meter. Consult Daniel Measureme
ページ19に含まれる内容の要旨
DANIEL™ SERIES 1500 TURBINE METER OCT 2013 Type: Square Wave Frequency Range: 0 to 5 kHz Max. Voltage: 30 Vdc Max. Current: 125 mA Max. Power: 0.5 Watts Transmission Distance: Without Preamp: 20 ft. (6.1 meters) With Preamp: 3,000 ft. (914 meters) Materials of Construction Meter Body (All sizes): Steel, Std. Options: Steel flanges/ Stainless Steel flowtube, all Stainless Steel Internal Components - Standard - Stainless Steel Bearings: Tungsten Carbide UMB Housing: Aluminum Rotor Rim: 3", 4" (opt
ページ20に含まれる内容の要旨
OCT 2013 DANIEL™ SERIES 1500 TURBINE METER This page intentionally left blank. 2-6 SPECIFICATIONS
