ページ1に含まれる内容の要旨
IMPORTANT NOTE!
This gauge has an odometer and
hour meter preset option that is
UTV-1500
only available for the first 10 miles
Gauge for Polaris RZR
(16km) and 1 engine hour of
operation. See “preset odometer”
Tachometer bar graph
and/or “preset hour meter” for
Speed display
instructions.
4
Speed unit indicators
3
Light sensor location
5
2
4x4 on indicator
6
km/h MPH
VOLTS SERV FUEL
Message center
HR
Check engine indicator
1
7
TEMP A B OIL
Gear position indicators
E F
Fuel bar graph
ページ2に含まれる内容の要旨
INSTALLATION: 1. Disconnect the battery to prevent possible damage to the electrical system or gauge during install. 2. Remove the rubber mounting ring and stock gauge by pushing the gauge out from behind the dash. The UTV gauge will mount in this mounting location. 3. If not installing temp and oil sensor pack (Dakota Digital part number SEN-24-1), skip to step 10. STEPS 4 THROUGH 9: INSTALLATION OF SENSOR PACK (SEN-24-1) 4. Remove the seats, console/engine cover, and center f
ページ3に含まれる内容の要旨
a. Turn the provided dual terminal pressure sensor into female end of pressure sensor extension assembly and tighten with appropriate wrenches. Teflon tape or similar sealant may be used to ensure a leak free installation. b. Locate and remove the plug from the pressure check port on the front of the engine. c. Turn the pressure sensor extension assembly into the port and tighten with a wrench. Again, sealant or tape may be used here to prevent leaks.
ページ4に含まれる内容の要旨
Follow the steps below for gauge setup: 1. Press and hold the switch while turning the key on. (If calibrating speed press and hold switch while starting engine.) 2. Release switch. Gauge will scroll through the main menu options. 3. When the desired option is displayed, press and release the switch to enter menu option. 4. Gauge will scroll through submenu options. Press and release the switch to enter submenu option. 5. In submenu option, press and release the switch t
ページ5に含まれる内容の要旨
Places gauge into demo mode until the key is turned off (useful for display at shows) Adjust dimming point on gauge Dimming function is off Gauge will dim when light on gauge face is very low (default) … 7 selectable dimming levels Gauge will dim early when more light is on gauge face Enables/disables dim output for other gauges Dim output will be high when gauge is dimming Dim output will be disabled (defa
ページ6に含まれる内容の要旨
This gauge has two service meters. These are a countdown hour meter and a countdown odometer. Both service meters can be disabled, or enabled independently. This allows for setting of two individual service points, one based on engine run time, the other based on odometer. When the setup point is reached, SERV will be displayed. Pressing the switch will clear the message until the next time the key is turned on. Once the service has been done, use the switch to select the service meter
ページ7に含まれる内容の要旨
A temp sensor and an oil pressure sensor along with the needed hardware and harness to install them are an optional accessory package (SEN-24-1) for the gauge. These provide additional gauge functions that are not included on the stock RZR gauge. If this sensor pack is installed, the display of these gauge values needs to be enabled. To do so, enter the setup menu and select the “” menu. Then select the “ TEMP OIL” option and change the setting from “” to “”. ENGINE CODE
ページ8に含まれる内容の要旨
engine is over heating. correct cause of engine overheating. is flashing in message center One of the countdown service meters Perform service and reset service meter by SERV has reached zero holding switch when service meter is displayed. If service meter operation is not desired, disable is flashing in the message center service meter by setting to in the setup menu. Temp / oil screen will not Temp / oil display is disabled. In setup menu change the option “ TEMP
