ページ1に含まれる内容の要旨
2005 Bike Light Owner’s Manual
ページ2に含まれる内容の要旨
Congratulations on your decision to purchase a Light & Motion Bicycle Lighting System. Prepare yourself to leave your car at home, rediscover your old stomping grounds and ride your bike year round. Please join us in viewing the world in a different light. To get the maximum satisfaction from your Light & Motion system, please take a moment to familiarize yourself with your new light by reading the instructions.
ページ3に含まれる内容の要旨
CAUTION - Bicycling in the dark is an inherently dangerous activity and no lighting system will guard you against inattentive motorists or other night time hazards. When not in use, ALWAYS unplug the light head from the battery. When unplugging the light head cable from the battery, always pull the connector, not the cable. Ride with an approved helmet and use extreme caution.You should carry an auxiliary light with you and wear reflective clothing. Make sure your bicycle is equipped with the le
ページ4に含まれる内容の要旨
Warranty Light & Motion offers a 30 day warranty on all lamps and a 90 day warranty on all batteries.All other facets of Light & Motion systems carry a one year warranty against manufacturer defects. Returning Products for Warranty Evaluation, or Repair: Should your system malfunction for any reason, contact the Light & Motion service department at (831) 645-1538 to schedule service and receive an RMA number to return your light to us. Please make sure to unplug the battery from the light before
ページ5に含まれる内容の要旨
Table of Contents Warranty and repair information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 ARC Li-ion parts identification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6 ARC NiMH parts identification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8 Solo Logic Li-ion and NiMH parts identification . . . . . . . . . . . . . . . . . . . . . .10 Commuter parts identification . . . . . . . . . . . . . . . . . . . . . . .
ページ6に含まれる内容の要旨
Light & Motion ARC Li-ion and Li-ion Ultra HID system parts identification Please verify the contents of your Light & Motion lighting system. 1. Lithium ion Turbo Charger 2. 11.1v Li-ion battery 3. 11.1v Ultra Li-ion battery 4.ARC Li-ion HID light w/ bar mount 5. Handle bar mount w/ spacers 6. Cabeza helmet mount 7. Slimline battery mount (6 amp/hr. Ultra battery ONLY) 8. Hook and loop bomber strap 9. Spare break-away disks (2) 6
ページ7に含まれる内容の要旨
1 2 3 4 5 6 7 8 9 7
ページ8に含まれる内容の要旨
Light & Motion ARC NiMH HID system parts identification 1. NiMH Turbo Charger 2. 10.8v NiMH Slimline battery 3.ARC HID light w/ bar mount 4. Handle bar mount w/ spacers 5. Cabeza helmet mount 6. Slimline battery frame mount with bomber strap 7. Spare break-away disks (2) 8
ページ9に含まれる内容の要旨
1 2 3 4 5 6 7 9
ページ10に含まれる内容の要旨
Light & Motion Solo Logic Li-ion and NiMH Mv system parts identification A) Solo Logic Li-ion 1. Solo Logic Mv light w/“Lefty” wing mount 2. Handle bar mount w/ spacers 3. Cabeza helmet mount 4. Hook and loop bomber strap 5. Li-ion Turbo Charger 6. 11.1v Lithium ion (4Amp/hr) Battery B) Solo Logic Mv NiMH 1. Solo Logic Mv light w/“Lefty” wing mount 2. Handle bar mount w/ spacers 3. Cabeza helmet mount 4. Hook and loop bomber strap 7.Trickle Charger 8. NiMH Turbo Charger (Optional w/ Logic Mv
ページ11に含まれる内容の要旨
1 2 3 4 5 6 7 8 9 11
ページ12に含まれる内容の要旨
Light & Motion Commuter parts identification 1.Trickle Charger 2. 7.2v NiMH battery 3. Commuter light w/ bar mount 4. Handle bar mount w/ spacers 5. Hook and loop bomber strap 6. Spare break-away disks (2) 12
ページ13に含まれる内容の要旨
1 2 3 4 5 6 13
ページ14に含まれる内容の要旨
Light & Motion Vega LED system parts identification 1.Vega wall charger 2.Vega light w/ bar mount 3. Handle bar mount w/ spacers 4. Spare break-away disks (2) 1 2 3 4 14
ページ15に含まれる内容の要旨
Charging your battery using TM the Turbo Charger The Light & Motion Turbo Charger is a universal input system that will work on any wall voltage from 90-260 volts. Depending on the outlet style you may require an adapter to plug the charger into the wall outlet. Charging the battery using the Li-ion Turbo Charger. Always fully charge your battery before its first use. Batteries are shipped partially charged and must be fully charged to achieve the proper run time. 1) Begin by plugging the powe
ページ16に含まれる内容の要旨
4) After approximately 2 hrs and 45 min. both the yellow and the green LED lights will be illuminated, this indicates the battery is 80% charged. 5) After an additional 2 hrs the battery will be fully charged and only the green LED on the left side will be liluminated. Two flashing LED lights indicate an error. If this happens remove the battery and unplug the Turbo Charger from the wall and wait about 5 minutes. Then try to charge the system again. The Li-ion Turbo Charger will charge a fully d
ページ17に含まれる内容の要旨
Charging the battery using the NiMH Turbo Charger. Always fully charge your battery before its first use. Batteries are shipped partially charged and must be fully charged to achieve the proper run time. Note: NiMH batteries require approximately 5-10 charge and discharge cycles to reach full capacity. Until the battery reaches full capacity your run times may be less than stated. 1) Begin by plugging the power cord into the charger and then into the appropriate wall socket. 2) Attach the batter
ページ18に含まれる内容の要旨
Two flashing LED lights indicate an error. If this happens, please remove the battery and unplug the Turbo Charger from the wall and wait about 5 minutes. Then try to charge the system again. The NiMH Turbo Charger will charge a fully depleted battery in approximately 3.5 hours. Leaving the battery on for approximately 1 additional hour will “top off” the battery for highest capacity. The NiMH Turbo Charger is designed to fully maintain the battery’s capacity throughout it’s life cycle.The batte
ページ19に含まれる内容の要旨
Charging the 7.2v NiMH battery using the trickle charger Always fully charge your battery before its first use. Batteries are shipped partially charged and must be fully charged to achieve the proper run time. Note: NiMH batteries require approximately 5-10 charge and discharge cycles to reach full capacity. Until the battery reaches full capacity your run times may be less than stated.The 7.2v trickle charger operates only on the specified wall voltage and should be used to charge the 7.2v bat
ページ20に含まれる内容の要旨
Installation of light head and battery Installing light head assembly Your Light & Motion Light head comes pre-assembled with the bar style mount attached to the light head. 1) Determine the best location for your handle bar mount as it relates to your specific brake/shifter bar layout. Ideally, the bar mount should be attached to the right and as close to the stem as possible. 2) After determining which bar spacer(s) to use (it may be necessary to cut spacers), orient the bar mount with the ope
