ページ1に含まれる内容の要旨
Workshop manual
Rider 11, Rider 13,
Rider 11 Bio, Rider 13 Bio,
English
Rider 16
ページ2に含まれる内容の要旨
Svenska – 31 Sve-5 225/232/235 Bruk 31 97-11-25, 08.46
ページ3に含まれる内容の要旨
Workshop manual Rider 11, Rider 13 Rider 11 Bio, Rider 13 Bio Rider 16 Contents Safety regulations ............................................... 2 Checking and adjusting throttle control .......... 33 General instructions ......................................... 2 Replacing articulated steering bearing........... 33 Special instructions .......................................... 2 Removal of swing axle ................................... 35 Special tools ......................................
ページ4に含まれる内容の要旨
Safety regulations Special instructions General instructions The fuel used in the ride-on mower has the The workshop handbook is written for personnel who following hazardous characteristics: are assumed to have general ride-on mower repara- tion and service know-how. • Toxic fluid and fumes • Can cause eye and skin complaints The workshop where the ride-on mower is repaired should be equipped with safety devices in • Can cause breathing difficulties accordance with local regulations. • Highly f
ページ5に含まれる内容の要旨
Special tools The following special tools are used when working on the ride-on mower. Special tools for the engine and transmission are specified in resp. Workshop Manuals. 506 66 48-01 Puller for engine pulley. 506 79 06-01 Ball-ended Allen key 3/8" to unscrew the engine pulley socket head cap screw (Briggs & Stratton). 506 89 92-01 Counter-hold for engine belt pulley. 506 89 93-01 Tool for the articulation spring. 535 41 32-01 Set of drifts for bushings on the swing axle. English – 3
ページ6に含まれる内容の要旨
Technical data Dimensions: Rider 11 Rider 13 Length 2 090 mm/6,85 ft 2 000 mm/6,56 ft Width 880 mm/2,89 ft 900 mm/2,95 ft Height (over steering wheel) 1 070 mm/3,52 ft 1 060 m/3,48 ft Weight 197 kg/433 lb 190 kg/419 lb Track front 720 mm/2,36 ft 625 mm/2,05 ft Track rear 620 mm/2,04 ft 625 mm/2,05 ft Wheel base 860 mm/2,81 ft 860 mm/2,81 ft Tyre size 16 x 6.50 x 8 16 x 6.50 x 8 Air pressure 60 kPa/8,5 PSI 60 kPa/8,5 PSI Max. gradient 15° 15° Engine: Rider 11 Rider 13 Manufacture Briggs & Stratto
ページ7に含まれる内容の要旨
Technical data Dimensions: Rider 16 Length 2 000 mm/6,56 ft Width 900 mm/2,95 ft Height (over steering wheel) 1 060 mm/3,48 ft Weight 208 kg/459 lb Track front 625 mm/2,05 ft Track rear 625 mm/2,05 ft Wheel base 860 mm/2,81 ft Tyre size 16 x 6.50 x 8 Air pressure 60 kPa/8,5 PSI Max. gradient 15° Engine: Rider 16 Manufacture Briggs & Stratton Model - 2002 28N707 Model 2003 - 282H070110E1 Power 11,4/15,5 kW/hp 3 Displacement 465 cm /28,42 cu inch Fuel min 85 octane unleaded Tank capacity 7 litres/
ページ8に含まれる内容の要旨
Technical data Control points Mowing deck parallelism with cutting height in pos. 1: ± 2 mm ± 0,079" Cutting height control in pos. 1: Rider 11 = 37 ± 2 mm 1,46" ± 0,079" Bio = 45 ± 2 mm 1,77" ± 0,079" Other = 40 ± 2 mm 1,57" ± 0,079" Synchronous transmission belt tension Bio 103 version 1, Combi 103: Automatic adjustment Synchronous transmission belt tension Bio 103 version 2 at 10 N force, impression: 7 mm 1/4" Synchronous transmission belt tension Bio 90 at 7 N force, impression: 8 mm 5/16" D
ページ9に含まれる内容の要旨
Delivery and dealer service Pre-delivery service 1. Top up battery with acid and recharge for four hours. 2. Fit the steering wheel, tow plate, and where appropriate other parts. 3. Adjust cutting unit: Adjust lift springs (effective weight of cutting unit should be 12–15 kg (26,5-33 lb), or set to maximum lift if brush is to be fitted). (Only applies to BioClip and Combi.) Adjust cutting unit so that rear edge is about 2–4 mm (1/8") higher than front edge. Adjust cutting unit height setting so
ページ10に含まれる内容の要旨
Delivery and dealer service Dealer service 100 hours service 1. Carry out 25 hours service as above. 25 hours service 1. Change the engine oil on the side-valve engine 2. Carry out 50 hours service as above. (With high load and temperature on the 3. Replace the pre-filter and filter cartridge in the overhead-valve engine). air filter. 2. Clean/replace the airfilter’s pre-filter or oil-foam 4. Replace the fuel filter in the pipe. element, if fitted. (More frequent intervals in dusty operating con
ページ11に含まれる内容の要旨
Delivery and dealer service Maintenance schedule The following is a list of the maintenance which should be conducted on the machine. Most of the points that are not covered by this workshop manual are covered by the operator’s manual. Daily Maintenance interval in maintenance hours Page Maintenance before 25 50 100 starting Check the oil level in the engine 12 Check the engine’s cooling air intake - Check the fuel pump’s air filter - Check the steering wires 29 Check the brakes 31 Che
ページ12に含まれる内容の要旨
Delivery measures Packaging and unpacking To our dealer On delivery from the factory the Rider is normally Well-performed delivery service is the first step to a packed in special packaging. This consists of a functioning aftermarket. A functioning aftermarket is wooden bottom board with a top part consisting of in everybody’s interest: heavy-duty cardboard held together by plastic film. • The customer is satisfied with their Rider. He/she knows where to go to get help if problems occur. WARNING
ページ13に含まれる内容の要旨
Delivery measures Battery WARNING! Measures for contact with acid External: Rinse thoroughly with water. Internal: Drink large quantities of water or milk. Contact a doctor as soon as possible. Eyes: Rinse thoroughly with water. Contact a doctor as soon asap. The battery gives off explosive gas. Sparks, naked flames and cigarettes must absolutely not be in the near vicinity of the battery. The battery is delivered dry-charged from the factory. The cells are fitted with sealing film. The battery
ページ14に含まれる内容の要旨
Delivery measures Steering wheel • Fit the steering wheel with the steering column tube on the steering shaft. • Screw in the socket head cap screw so that it goes in the slot on the steering shaft. Work on the steering wheel and tighten the socket head cap screw so that it bottoms in the slot. • Fit the lock nut on the socket head cap screw. Tow plate The tow plate is fitted the “wrong way round” at the factory for transport reasons. Fit the tow plate on the rear bumper as shown in the diagram.
ページ15に含まれる内容の要旨
RIDER 850 Delivery measures Checking the oil level in the transmission (Not Rider 11) Remove the transmission cover. Loosen both screws (one on each side) and lift off the transmission cover. Check that there is oil in the transmission’s oil tank. Fill if necessary with engine oil SAE 10W/30 (class SF–CC). IMPORTANT INFORMATION Check and top up with oil after each test drive. The oil level will drop if there are air pockets in the transmission. Wheels Fit the wheels (certain markets). The tyre p
ページ16に含まれる内容の要旨
Delivery measures Test running Fill up with petrol. The engine should be run on the lowest 85 octane unleaded petrol (no oil admixture). It can be beneficial to use environmentally adapted alkylate petrol. Do not use petrol that contains methanol. WARNING! Petrol is highly inflammable. Observe caution and fill up with petrol outdoors. WARNING! Never run the engine indoors, or in enclosed or poorly ventilated areas. Engine exhaust fumes contain poisonous carbon mon- oxide. Start the engine. Check
ページ17に含まれる内容の要旨
Delivery measures Check the function of the mowing deck and that there is no abnormal noise. The mowing height can be regulated in 9 different positions with the lever. Deck with rear ejector, 40-90 mm, mowing height (1 9/16" - 3 9/16") BioClip- and Combi- deck, 45-95 mm, mowing height (1 3/4" - 3 3/4") Speed regulator Check that the engine’s maximum speed is regulated at: Rider 11 2 900 - 3 100 rpm Rider 13 2 900 - 3 100 rpm Rider 16 2 900 - 3 100 rpm Rider 16 2003 - 2 800 - 3 000 rpm Administr
ページ18に含まれる内容の要旨
RIDER 850 R RIDER IDER 850 850 Design and function General and for best possible cutting results. Husqvarna Riders is a series of ride-on mowers Husqvarna Riders can, moreover, be equipped with a large capacity. It is available in several sizes, with various accessories such as moss rake and from the smallest Rider 11 to the largest Rider dozer blade which make them flexible working ProFlex 21. tools throughout the year. This manual deals with the slightly smaller Rider 11 and Rider 11 Bio can
ページ19に含まれる内容の要旨
Design and function Serial number The serial number can be found on the printed plate attached to the front, left-hand side under the seat. Stated on the plate, from the top are: • The machines type designation. • The manufacturer’s type number. • The machine’s serial number. State the type designation and serial number when ordering spare parts. On older machines the engine’s manufacturing number is punched on a plate that is riveted to the fan cover. On newer engines in Rider 16 the data is pu
ページ20に含まれる内容の要旨
Design and function Engine The order numbers for the respective Rider models These Husqvarna Riders have single-cylinder, air- are found in the table below. Please state these cooled engines from Briggs & Stratton. when ordering manuals: More intricate engine repairs are not described in Model B & S model no. this workshop handbook, these can instead be Rider 11 28B707 read in Briggs & Stratton's own handbooks which Rider 13 286707 contain detailed information about adjusting and Rider 16 -2002
