ページ1に含まれる内容の要旨
Sub-Frame Hitch
Installation
Mfg. No. 1695195
For Prestige / 1800 / 2800, Conquest / 1700 / 2700, &
Instructions
Broadmoor / 1600 / 2600 Series Tractors
This kit is required when installing front mounted
snowthrowers.
1
ページ2に含まれる内容の要旨
Installation Instructions Sub-Frame Hitch Main Hitch Components (All Applications) 28 29 27 30 25 29 41 33 39 38 40 37 36 35 42 1 2 3 32 28 27 33 32 43 25 33 25 33 29 25 27 25 34 4 28 28 26 27 28 27 25 5 27 30 28 31 50 22 6 46 25 45 49 22 7 24 48 8 23 9 15 9 9 47 17 16 10 13 18 21 Front Hole for Dozer Applications Hydraulic Rear Hole for Snowthrower Applications Front Pulley - Two-Stage 20 Lift Snowthrower Application 14 11 13 29 44 27 12 19 Early Manual 11 Lift Only 51 9 (See Instructions) 2
ページ3に含まれる内容の要旨
Sub-Frame Hitch Installation Instructions Ref Part No. Qty. Description 1 1723292A 1 SHAFT & HOOK ASSY 2 1653768A 1 CLAMP, Support 3 1931335 4 CARRIAGE BOLT, 5/16-18 x 1 4 1919381 4 WASHER, 11/32 5 1917356 3 LOCKWASHER, 5/16 6 1917372 4 NUT, 5/16-18 7 105249 1 PIN, Round Head, 3/8 x 2-3/8 8 1724025 1 LIFT LEVER ASSY. 9 2176012 4 SAFETY CLIP 10 1722946 1 LIFT ROD 11 8031007 2 SET COLLAR 12 171011 1 SPRING, Compression 13 1928721 2 SET SCREW, 5/16-18 x 1/2 14 1723115 1 ROD GUIDE 15 1733812 2 ROD,
ページ4に含まれる内容の要旨
Installation Instructions Sub-Frame Hitch NOTE: Please read through these instructions and the Change Pulley & Belt - Two-Stage Blower instructions of any other attachments before beginning Only installation. 1. If using this hitch with a two-stage snowthrower, the front idler pulley must be switched from the right hand WARNING side of the hitch bracket, to the left, and an additional Before beginning any service work turn off the 3/8 x 1 x 1/2 spacer (B, Figure 3) and 3/8-16 x 2-1/4 PTO, set th
ページ5に含まれる内容の要旨
Sub-Frame Hitch Installation Instructions Snowthrower A & Dozer B E C Applications D A B Figure 5. Assemble Lift Rod C D A. Lift Rod C. Spring B B. Set Collar D. Rod Guide Mower A Applications B G Figure 6. Early/Later Lift Links A. Early Model Lift Link A B. Later Model Lift Link Assemble Lift Rod 1. Install the set collars (B, Figure 4), spring (C), and rod guide (D) on the lift rod (A) as shown. Final D C adjustment of the set collars will be made after the F hitch and attachment are insta
ページ6に含まれる内容の要旨
Installation Instructions Sub-Frame Hitch A B C D E Figure 9. Install Hitch A. J-Hooks D. Hook B. Hitch Rod E. Clamp Plate C. Hitch Rod 5. Push the clamp plate (D) backwards until it is snug Install Hitch against the lift shaft. Tighten the clamp plate hard- 1. Slide the hitch under the tractor. ware (E). 2. Raise the rear of the hitch and place the hook (C) over the lift shaft. 3. Connect the front of the hitch to the tractor J-hooks (A, Figure 9) using the hitch rod (B) and a safety clip i
ページ7に含まれる内容の要旨
Sub-Frame Hitch Installation Instructions D A B C A B C Figure 11. Install Lift Rod - All Models A. Lift Lever B. Lift Rod Figure 10. Install Lift Lever C. Clip A. Lift Lever B. Lift Shaft C. Safety Clip D. Clevis Pin Install Lift Rod 1. Slide the lift lever (A, Figure 10) onto the end of the tractor lift shaft (B) under the right side footrest. 2. Use the tabs on the lift lever (A) to capture the tractor lift arm. Secure in place with a clevis pin (D) and safety clip (C). 3. Insert the rear
ページ8に含まれる内容の要旨
Installation Instructions Sub-Frame Hitch Snowthrower C Position D A B E F A. Hitch Rod B. Hitch Rod C. Lift Lever Extension D. Lift Link (Manual) E. Pressure Lock Plate (Hydraulic) F. Hook Figure 12. Normal Installation & Removal REMOVAL NORMAL INSTALLATION NOTE: After removing components, reinstall the clevis 1. Insert the hook (F, Figure 12) into the back of the pins and clips to prevent loss. hitch. Mount the rear of the hitch on the lift cross- shaft. 1. Disconnect the lift rod from the a
ページ9に含まれる内容の要旨
Sub-Frame Hitch Installation Instructions Snowthrower Snowthrower & Dozer & Dozer E Applications Applications A A B F C D C D E B Mower Mower G Applications Applications A A B F D F C G E Figure 13. Lift Lock Plate - Hydraulic Lift Models Figure 14. Lift Link - Manual Lift Models A. Lift Cylinder A. Pin B. Flat Head Pin (Original) B. Rear Hole of Lift Bar (Snowthrower Applications) C. Flat Head Pin (New) C. Spacer D. Lock Plate D. Hair Pin Clip E. Hair Pin Clips E. Upper Hole (Snowthrower Appl
ページ10に含まれる内容の要旨
Installation Instructions Sub-Frame Hitch NOTES MANUFACTURING, INC. Form No. 1734116 Rev. 10/2006 500 N Spring Street / PO Box 997 © 2006 Briggs & Stratton, Inc. All Rights Reserved Port Washington, WI 53074-0997 USA TP 200-4417-00-AT-SMAN
