ページ1に含まれる内容の要旨
MOW’N MACHINE
CZR2242B
872311G
22HP B&S W/42” SIDE DISCHARGE
(S/N 000050 AND ABOVE)
CZR2652B
872313G
26HP B&S W/52” SIDE DISCHARGE
(S/N 000050 AND ABOVE)
Includes Maintenance
Instructions
RF4166230
MAN0864
REV A 12-2010
PARTS / OPERATOR'S MANUAL
ページ2に含まれる内容の要旨
CALIFORNIA Proposition 65 Warning WARNING Diesel engine exhaust and some of The engine exhaust from this product its constituents are known to the State contains chemicals known to the State of California to cause cancer, birth of California to cause cancer, birth defects and other reproductive harm. defects or other reproductive harm. Californie Proposition 65 Avertissement AVERTISSEMENT Les échappements des moteurs diesel et certains de leurs composés sont reconnus par l’Etat de L’émis
ページ3に含まれる内容の要旨
WOODS IMPORTANT MESSAGE TO THE DEALER: Assembly and proper installation of this product is the responsibility of the Woods® dealer. Read manual instructions and safety rules. Make sure all items on the Dealer’s Pre-Delivery and Delivery Check Lists in the Set-Up instructions are completed before releasing equipment to the owner. The dealer must complete the Product Registration online at the Woods Dealer Website or complete the mail-in form included with the Operator’s Manual. If using the
ページ4に含まれる内容の要旨
WOODS TABLE OF CONTENTS FIGURES PAGE SAFETY .......................................................................................................................................................5-11 SET-UP INSTRUCTIONS .........................................................................................................................12, 13 LABELS ................................................................................................................................................
ページ5に含まれる内容の要旨
SAFETY WOODS This symbol means: NOTICE !!! ATTENTION! Unauthorized modifications may present extreme BECOME ALERT! safety hazards to operators and bystanders and could also result in product damage. Your safety and the safety of others is involved. Woods strongly warns against, rejects and disclaims any modifications, add-on accessories or product Signal word definitions : alterations that are not designed, developed, tested The signal words below are used to identify levels and a
ページ6に含まれる内容の要旨
SAFETY WOODS PREPARING FOR SAFE OPERATION Operator preparation and training WARNING Read the Operation & Safety Manual - If an operator or mechanic cannot read English, it is the owner's responsibility to explain this material to them. If any portion of this material is unclear, contact your factory representative for clarification. All rotary lawnmowers are potentially - Become familiar with the safe operation of the dangerous. They can amputate hands and equipment, operator cont
ページ7に含まれる内容の要旨
SAFETY WOODS OPERATING SAFELY Machine preparation - Check operator presence interlock system and In general brake operation. Adjust or repair any problems - Use extra care when loading or unloading the before using. machine into a trailer or truck. - Do not tamper with or defeat safety devices. - Slow down and use caution when making turns Keep guards, shields and interlock safety devices and crossing roads and sidewalks. Stop blades if in place and in proper working condition. They
ページ8に含まれる内容の要旨
SAFETY WOODS Starting Interrupting operation - Start only according to instructions in this manual - Before leaving the operator's position: or on the machine. - Park on level ground. - Disengage the PTO. - Before attempting to start the engine, make sure: - Set the parking brake. - the parking brake is on; - Shut off the engine and remove the key. - the PTO is disengaged; - the traction drive is in NEUTRAL. - Disengage the PTO and wait until the blades quit rotating: - When starting t
ページ9に含まれる内容の要旨
SAFETY WOODS MANEUVERING SAFELY In general - Use extra care with grass catchers or other - Slow down before turning. attachments. These can change the stability of the machine. - Do not mow in reverse unless absolutely necessary. Always look behind and down - Remove obstacles such as rocks, tree limbs etc. for small children and pets before and during - Avoid driving over obstacles such as ruts, holes, backing. rocks and roots whenever possible. Be alert to - Be aware when approaching
ページ10に含まれる内容の要旨
SAFETY WOODS MAINTENANCE SAFETY Blades WARNING - Mower blades are sharp and In general can cut. Use extra caution - Maintain machine according to manufacturer's when handling. Remove ob- schedule and instructions for maximum safety structions with care. Wrap the and best mowing results. blade(s) or wear gloves. - Park machine on level ground. - Be aware that rotating one - Never allow untrained personnel to service ma- blade on multiblade mowers chine. can cause other blades to
ページ11に含まれる内容の要旨
SAFETY WOODS JUMP STARTING BATTERY WARNING 1. Be sure the jumper cables are in good condition. Battery acid is caustic and fumes Turn off the ignition and all electrical accessories are explosive and can cause on both machines. serious injury or death. 2. Position the machine with a good (charged) bat- To reduce the risk of personal tery next to but not touching the machine with the injury when working near a bat- dead battery so jumper cables will reach. tery: 3. When making cable con
ページ12に含まれる内容の要旨
SET UP INSTRUCTIONS WOODS TOOLS REQUIRED FOR ASSEMBLY - Wrecking bar - Claw hammer - Sockets: 1/2”, 15/16 - Wrenches: 18mm, 1/2”, 9/16”, 3/4”, 15/16” - Tire pressure gauge NOTE: All references below to the “right” or “left” are with respect to an operator at the controls. 1. UNCRATE UNIT a) Discard packing materials. Loosen the caster wheel axle bolts and bumper bolts to remove the shipping brackets. Discard shipping brackets. b) Re-install and tighten bumper bolts. c) Tighten caster whe
ページ13に含まれる内容の要旨
SETUP INSTRUCTIONS WOODS 4. FINAL PREPARATIONS - Check the engine and hydraulic oil levels. Top off with the correct oil if necessary. Use 10W30 motor oil for the engine. Use fresh, clean 20W50 motor oil for the hydraulic system. - Insure Battery cables are connected properly. Battery acid is caustic. Fumes are explosive and can cause serious injury or death. Use insulated tools, wear protective glasses or goggles and protective clothing when working with batteries. Read and obey the b
ページ14に含まれる内容の要旨
PTO SWITCH LABELS WOODS bORDER IS NOT BLUE, BORDER IS WHITE. F N N R 4165616 F N N 4165662 4165615 R 14
ページ15に含まれる内容の要旨
LABELS WOODS 15
ページ16に含まれる内容の要旨
LABELS WOODS BEFORE STARTING OR SERVICING: Read and understand the Operator's Manual & labels. - Be sure machine is in safe operating condition. - Move traction levers to neutral lock, parking brake to ON. - Set PTO switch to OFF. BEFORE LEAVING SEAT: - Move traction levers to neutral lock, parking brake to ON. - Set PTO switch to OFF. - Turn engine keyswitch to OFF. - Remove key. AVOID SERIOUS INJURY OR DEATH: - Read and obey the Operation & Safety Manual. - Remove objects that could be thro
ページ17に含まれる内容の要旨
LABELS WOODS 17
ページ18に含まれる内容の要旨
CONTROLS WOODS KEYSWITCH (K) - The keyswitch has three positions: OFF, RUN, and START. Insert the key and turn it clockwise to move the switch from OFF to RUN. Turn it further to START and hold to engage the starter. Release the key and the switch will return to RUN from START. Turn the key counterclockwise to OFF to stop the engine. THROTTLE (T) - Move the throttle lever forward to increase engine speed until the maximum governed engine RPM is reached. Move the lever rearward to
ページ19に含まれる内容の要旨
CONTROLS WOODS FUEL SELECTOR VALVE (U) The fuel tank selector valve is located behind the seat. The fuel tank selector valve has three positions: Off: The tank selector is off when the lever points down. The selector should be off whenever the machine is transported or stands unused for any length of time. Shutting off the fuel supply avoids the possibility of flooding should any dirt get under the carburetor float needle. Leaving the tank selector in either tank position can allow
ページ20に含まれる内容の要旨
CONTROLS WOODS Reverse movement - To move the machine straight back, pull both traction levers back equally from their neutral position. Reverse speed increases as the levers are moved back farther. Maximum reverse speed is reached when the levers hit the rear of the forward-reverse slot. When moving in reverse, push- ing the levers forward slows the machine, and the machine stops when the neutral position is reached. NOTE: Reverse is spring loaded to return to neutral. This spring
