ページ1に含まれる内容の要旨
Operator's Manual
21" Three-in-One
Lawn Mower
Model 466
IMPORTANT: Read safety rules and instructions carefully before operating equipment.
Warning: This unit is equipped with an internal combustion engine and should net be used on or near any unimproved forest-
covered, brush-covered or grass-covered land unless the engine's exhaust system is equipped with a spark an'ester meeting
applicable local or state laws {if any). If a spark arrestor is used, it should be maintained in effeutive werFdngo
ページ2に含まれる内容の要旨
TABLEOFCONTENTS Content Page Important Safe Operation Practices ................................................................... 3 Slope Gauge ...................................................................................................... 6 Assembling Your Lawn Mower .......................................................................... 7 Know Your Lawn Mower .................................................................................... 10 Operating Your Lawn Mower ..........
ページ3に含まれる内容の要旨
SECTION 1: IMPORTANT SAFEOPERATION PRACTICES WARNING: This symbol points out important safety instructionswhich, if net fol]owed, could endanger the personal safety and/or property of yourself and others. Read and fel]ew all instructiens inthis manual before attempting te eperate this machine. Fai]ure to comply with these instructions may result in personal iniury. When yeu see this symbol--HEED ITS WARNING. WARNING: Engine exhaust, some ef its censtituents, and certain vehicle cempenents centai
ページ4に含まれる内容の要旨
serious personal injury. If you feel you are losing 2. Do not mew slepes greater than 15 degrees as yeur feeting, release the blade control handle shown on the slepe gauge. immediately and the blade will step rotating within 3. Do not mew en wet grass. Unstable footing could three seconds. cause slipping. "16. Mew in daylight or geod artificial light. Walk, never run. Step the blade when crossing gravel drives, Children walkways er reads. Tragic accidents can occur if the operator is not alert t
ページ5に含まれる内容の要旨
fshotorrunning. Allow engfne to cool at least two lead to improper performance and compromise minutes before refueling. safety!" "10. Never over fill fuel tank. Ff]l tank to no more than ½ 4. Mower blades are sharp and can cut. Wrap the fnch below bottom of ffller neck to provfde space for blade or wear gloves, and use extra caution when fuel expansion. servicing them. "11. Replace gasolfne cap and tighten securely. 5. Keep al] nuts, bolts, and screws tight to be sure the "12. If gasoline is spi
ページ6に含まれる内容の要旨
4 SIGHT AND HOLD THIS LEVEL WITH A VERTICAL TREE A POWER POLE A CORNER OF A BUILDING OR A FENCE POST I I ¢,D 15o WARN,NG Do not mow on inclines with a slope in excess of "I5 degrees (a rise of approximately 2-'I12 feet every "I0 feet). A riding mower your footing and you could slip, resulting in serious injury. could overturn and cause serious injury. If operating a walk-behind mower on such a slope, it is extremely difficult to maintain Operate RIDING mowers up and down slopes, never across th
ページ7に含まれる内容の要旨
SECTION 3: ASSEMBLING YOUR LAWNMOWER Removing UnitFromCarton • Remove staples, break g]ue on top flaps or cut tape Lift lower handle at carton end and peel along top flap to open Lower Han,,_"_ carton. • Remove loose parts if included with unit (i.e., operator's manual, hardware pack etc.). • Cut corners and lay carton down flat. Remove packing material. Lift u • Rel] or slide unit out ef carton. Check carton thoroughly for loose parts. NOTE: Make sure not to crimp cables while removing loose pa
ページ8に含まれる内容の要旨
Insert post of cable ties that are on lower handle AssemblingGrassBag into the holes provided on the lower handle. The • Join the rear frame and front frame assembly as holes may be on the inside or outside. Pull cable shown in Figure 7A. ties tight and cut off the extra. See Figure 5 below. • Place the bag over the frame (black plastic side is Cable "lle the bottom of bag). Slip the openings in the side of \ the plastic channels on the bag over the hooks on '\ \ the grass catcher frame. Po_t on
ページ9に含まれる内容の要旨
Converting toSideDischarge • Your mower has been shipped as a mulcher. Te convert it to a side-discharge mower, lift the mulching plug. Slide the two hooks en the side_ discharge deflscter under the hinge pin en the mulching plug assembly. Lower the mulching plug. See Figure "10. • De net remove the side mulching plug at any time, even when you are not mulching. Mulching Plug Figure 9 RemovingGrassCatcher • Liftthe rear discharge door on the mower. • Liftthe grass catcher up, out of the slots in
ページ10に含まれる内容の要旨
SECTION 4: KNOWYOURLAWNMOWER Read this owner's manual and safety rules befere operating your lawn mower. Compare the illustrations tn Figure "1 1 with your lawn mewer te familiarize yourself with the location of various contrels and adiustments. Lower Bail Handle Starter Rope Oil Plug Gasoline Fill _-- Spark Plug Bag*Fili Indicator Plug MulCh _ =gHeight Adjustment Lever* Side Discharge * Fourth I_._r not shown Chute Deflector Figure 11 RecoilStarter Lnwer Ball Handle The recoil starter ls attach
ページ11に含まれる内容の要旨
SECTION 5: OPERATING YOURLAWNMOWER GasandOilFill-Up Using Your Lawn Mower • Do not operate the mower without the mulching WARNING: Never fill fuel tank indoors=or cover, the grass catcher bag, or the discharge when engine is running or hot. Do not smoke chute properly installed. ............. when filling up the fuel tank. • Be sure that the lawn is clear of stones, sticks, wire, or other objects which could damage lawn mower • Service the engine with gasoline and oil as or engine. Such objects
ページ12に含まれる内容の要旨
SECTION 6: MAINTAINING YOURLAWNMOWER and surrounding areas while the mower engine fs WARNING: Always stop the engine and hot because temperature of these areas of the disconnect the spark plug wire before engine may exceed "150oF. ............ performing any maintenance work or adjustments on your lawn mower. Lubrication (see Figure 12 ) Wheels Cleaning theMower • Lubricate the wheels and bearings, if so equipped, • Clean the underside of the mower deck after each at least once a season with lig
ページ13に含まれる内容の要旨
SECTION 7: SERVICING YOUR MOWER recommended torque. Refer to 'Blade Mounting BladeCare Torque' information below. Periedically inspect the blade adapter and pulley for • Install the blade assembly on the engine cracks, especially if you strike a foreign object. Replace crankshaft. Secure with the hex bolt and bell when necessary. washer (cupped side of washer to blade) and tighten to the recommended torque. Refer to 'Blade _%== WARNING: When remeving the cutting Mounting Torque' information belo
ページ14に含まれる内容の要旨
Right Front Left Front Wheel Wheel \\4 / Loosen this screw Shoulder Screw Pulley Figure 15 Replacing RearFlap Screw Front Drive Transmission • To remove rear flap, cut off the flat end of the wire Cover rod which secures it to the deck. See Figure 16. • Attach the new flap and new rod to deck, bending Figure 14 the ends of the new rod over to secure to deck. • Slide the belt off the engine pulley and around the Rear Discharge blade. See Figure 15. Door ,_.= WARNING: As always, use a thick piece
ページ15に含まれる内容の要旨
,\ \ \ Notch AdjustTnent J Lever Handle Figure 17 Figure 18 Carburetor Cutting Height IMPORTANT: All wheels must be placed in the same _'k WARNING: If any adjustments are made to relative position. Athe engine (e.g. carburetor)whi]e the engine is / .... running, keep clear of al] moving parts. Be • For rough or uneven lawns, move the height careful of heated surfaces like the muffler. adjustment lever tea higher pesition. This will help stop scalping of the grass. NOTE: A dirty air cleaner may c
ページ16に含まれる内容の要旨
SECTION 10: TROUBLE-SHOOTING GUIDE Problem PossibleCeuse Corrective Action Engine fails to start 1. Blade control hand]e disengaged "1. Engage blade control handle 2. Spark plug wire disconnected 2. Connect wire to spark plug 3. Fuel tank empty, or stale fuel 3. Fill up tank with fresh gasoline 4. Blocked fuel line 4. Clean fuel line 5. Faulty spark plug 5. Clean, adiust gap, or replace 6. Engine flooded 6. Wait a few minutes and start again Engine runs erratic "1. Spark plug wire loose "1. Conn
ページ17に含まれる内容の要旨
Safety & Decorative Labels iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii ¸_(Mo_ELi_TEiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii 777_0118 777D6002 ....... iiiiii_7_B060!0iiiiiiiiiiiiiii iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii _NOI'E: _lqO r',.I T B_$ LOG_75 _B27_,40 17
ページ18に含まれる内容の要旨
SECTION 11:PARTSLISTFORMODEL 466 \4 17 11 25 24 49 7O IMPORTANT: For a proper working machine, use Factory Approved Parts, 78 V-BELTS are specially designed to engage and disengage safely. A substitute (non OEM) V-Belt can be dangerous by not disengaging completely. 18
ページ19に含まれる内容の要旨
Model466 Ret. Pert No. Pert Description Ref. Pert No. Pert Description No. No. 1. 747-2136 Lower B_I Handle 49. 731-1404A Mulch Plug 2. 647-0004 Blade Control Handle 50. 731-1409 Discharge Deflector SD "F Screw 1/4-20 x 0.5" 3. 749-1501 Upper I-landle 51. 710-0599 4. 710-1270 Oval C-Sunk Scr. 1/4-20 x 1.31" 52. 736-0270 Bell Washer 0.265" x 0.75" Front Baffle 5. 746-0883 Control Housing 53. 782-5002 6. 712-0324 I-lex Lock Nut 1/4-20 54. 618-0657 Transmission Assembly Compl. 7. 746-0551 Screw #12
ページ20に含まれる内容の要旨
MANUFACTURER'S LIMITED WARRANTY FOR: The limited warranty set forth below is given by Troy-Efilt LLC d. Troy-EfiltLLC does not extend any warranty for products sold or exported outside of the United States, with respect to new merchandise purchased and used in the United States, its possessions and territories. its poesesions and territories, except those sold through Troy-Efilt LLCs authorized channels of export Troy-Hilt LLC warrants this product against defects for a distribution, period of t
