ページ1に含まれる内容の要旨
Safety Instructions & Operator’s Manual for
SCRAMBLER
ZERO-TURN
HYDRO DRIVE
SERIES 6
MODELS
SZT18336BVE
SZT18386BVE
MODEL NUMBER EXPLANATION
S Z T 18 33 6 B V E
MODEL DESIGNATION ENGINE OPTIONS
DRIVE SYSTEM TYPE ENGINE TYPE
ENGINE HORSE POWER * SERIES DESIGNATION
CUTTING WIDTH
S – Scrambler 18 – 18.0 HP Engine 33 - 33” Cutting Deck 6 - Series Designation B - Briggs Engine E - Electric Start
ZT – Zero Turn 38 - 38” Cutting Deck V – Over Head Valve
ページ2に含まれる内容の要旨
IMPORTANT SAFETY INSTRUCTIONS WARNING: This powerful cutting machine is capable of amputating hands and feet and can throw objects that can cause injury and damage! Failure to comply with the following SAFETY instructions could result in serious injury or death to the operator or other persons. The owner of the machine must understand these instructions and must allow only persons who understand these instructions to operate machine. Each person operating the machine must be of sound mind
ページ3に含まれる内容の要旨
IMPORTANT SAFETY INSTRUCTIONS PREPARATION OPERATION (Continued From Previous Page) 1. Mount and dismount machine from left side. 6. Check the area to be mowed and remove all objects Keep clear of discharge opening at all times. such as toys, wire, rocks, limbs and other objects 2. Start engine from operator's seat, if possible. that could cause injury if thrown by blade or Make sure blades are OFF and parking brake is interfere with mowing. set. 7. Keep people and pets out of mow
ページ4に含まれる内容の要旨
IMPORTANT SAFETY INSTRUCTIONS TOWING MAINTENANCE 1. Tow only with a machine that has a hitch (Continued From Previous Column) designed for towing. DO NOT attach towed 15. Maintain or replace safety and instruction labels as necessary. equipment except at the hitch point. 16. Use only genuine SNAPPER replacement parts 2. Follow the manufacturer’s recommendation for to assure that original standards are maintained. weight limits for towed equipment and towing on slopes. 3. DO NOT
ページ5に含まれる内容の要旨
TABLE OF CONTENTS IMPORTANT SAFETY INSTRUCTIONS........................................................................ 2-4 TABLE OF CONTENTS......................................................................................................5 SECTION 1 - FAMILIARIZATION................................................................................... 6-7 SECTION 2 - OPERATING INSTRUCTIONS............................................................... 8-12 Pre-Start Checklist ...........
ページ6に含まれる内容の要旨
Section 1 - FAMILIARIZATION IMPORTANT! The figures and illustrations in this manual are provided for reference only and may RIGHT MOTION OPERATOR’S differ from your specific model. Contact your CONTROL LEVER SEAT Snapper dealer if you have questions. FUEL TANK ENGINE SPEED & CHOKE CONTROL ARM REST (2) RIGHT CONTROL LEFT MOTION PANEL IGNITION CONTROL LEVER SWITCH PARKING BLADE BRAKE SWITCH LEFT CONTROL PANEL CUTTING DECK HEIGHT ADJUSTMENT
ページ7に含まれる内容の要旨
Section 1 - FAMILIARIZATION 1.3 BASIC CONTROLS AND THEIR FUNCTIONS 1.3.4. MOTION CONTROL LEVERS The figures below identify each of the operator controls Controls direction and steering of machine when and their basic function. Controls will be described in driving. Refer to Section “MOTION CONTROL” for greater detail further on in this manual. detailed operation of motion control levers. 1.3.1. IGNITION SWITCH (Left Control Panel) Starts and stops engine. Refer to Section “ENGINE OP
ページ8に含まれる内容の要旨
Section 2 - OPERATING INSTRUCTIONS VENT SCREW WARNING DO NOT attempt to operate the machine until you have FUEL FILLER CAP read this manual thoroughly and become familiar with all WITH VENT SCREW. TIGHTEN CAP AND controls and operating procedures. Serious injury or OPEN VENT SCREW damage can result. AFTER REFUELING. 2.1 PRE-START CHECK LIST FUEL CAP Make the following checks and perform the service required before each start-up. 2.1.1. Check tires and add or release air as ne
ページ9に含まれる内容の要旨
Section 2 - OPERATING INSTRUCTIONS 2.3 MOTION CONTROL IMPORTANT: This machine is equipped with hydrostatic drive. The direction and speed of movement are controlled by dual motion control levers. A small amount of movement of either lever may cause the machine to move instantly, and can result in severe injury or damage. Operate levers slowly and smoothly. To safely develop driving skills, practice driving the machine with blades disengaged, engine speed at a slow settin
ページ10に含まれる内容の要旨
Section 2 - OPERATING INSTRUCTIONS 2.3.4. CONVENTIONAL TURNING WARNING 1. To turn left, slowly ease back on the left lever while keeping or increasing pressure on the right Zero-turning the machine at any speed can result in lever. See Figure 2.6. The more you ease off on the operator disorientation, or in operator being thrown left lever and/or push on the right lever, the tighter the from the machine. Exercise extreme caution when turn. executing a zero-turn. 2. To turn rig
ページ11に含まれる内容の要旨
Section 2 - OPERATING INSTRUCTIONS 2.4 MOWER OPERATION 2.4.3. MOWER BLADE DISENGAGEMENT Push Blade Switch in to its off (‘0’) position to 2.4.1. CUTTING HEIGHT ADJUSTMENT disengage mower blade(s). See Figure 2.10. This machine has seven different cutting height positions. IMPORTANT: When positioning the cutting deck into a higher cutting position, pull up on the deck WARNING lift handle only, it is not necessary to pull up on the Blades must stop rotating in 5 seconds or less af
ページ12に含まれる内容の要旨
Section 2 - OPERATING INSTRUCTIONS 2.5 SAFETY INTERLOCK SYSTEM CHECKS This machine is equipped with an electrical safety interlock system that is provided for the safety of the operator and others. All safety devices must be in place and functioning properly before operating the machine. Perform the following interlock system checks periodically during the operating season. Contact your authorized Snapper dealer if you have questions. WARNING DO NOT operate machine
ページ13に含まれる内容の要旨
Section 3 - MAINTENANCE 3.2.2. CHECK MOWER BLADE 3.1 INTRODUCTION 1. Close vent on fuel cap and make sure cap is To retain the quality of the SCRAMBLER, use genuine tight. See Figure 2.2. SNAPPER replacement parts only. Contact a local 2. Engage parking brake. SNAPPER dealer for parts and service assistance. For 3. Turn key to “STOP” position and remove key from the correct part or information for a particular mower, ignition switch. Remove spark plug wires. always mention the m
ページ14に含まれる内容の要旨
Section 3 - MAINTENANCE 3.2.4. CHECK TRANSAXLE DRIVE BELTS WARNING 1. Checking Transaxle Belt Tension DO NOT attempt any adjustments, maintenance, The transaxle drive belt requires no adjustment. If service or repairs with the engine running. Stop belt is frayed, slit, severed or belt strands exposed, engine. Stop blade. Engage parking brake. Remove replace belt before operating mower. key. Remove spark plug wire from spark plug and secure away from plug. Engine and components are 3.3
ページ15に含まれる内容の要旨
Section 3 - MAINTENANCE WARNING 4. Mower Deck Levelness DO NOT attempt any adjustments, maintenance, Check mower deck for proper levelness. Adjust as service or repairs with the engine running. Stop required. Refer to Section “MOWER DECK engine. Stop blade. Engage parking brake. Remove ADJUSTMENT – LEVELNESS”. key. Remove spark plug wire from spark plug and 5. Cleaning Mower Deck secure away from plug. Engine and components are a. Close vent on fuel cap and make sure cap is HOT. A
ページ16に含まれる内容の要旨
Section 3 - MAINTENANCE WARNING FRONT STRUCTURE ACCESS HOLE DO NOT attempt any adjustments, maintenance, service or repairs with the engine running. Stop engine. Stop blade. Engage parking brake. Remove LUBRICATE key. Remove spark plug wire from spark plug and PIVOT secure away from plug. Engine and components are SHAFTS HOT. Avoid serious burns, allow all parts to cool before working on machine. Fuel Filler Cap and Vent must be closed securely to prevent fuel spillage. 2. Mower
ページ17に含まれる内容の要旨
Section 3 - MAINTENANCE WARNING DO NOT attempt any adjustments, maintenance, service or repairs with the engine running. Stop NEW FUEL FILTER engine. Stop blade. Engage parking brake. Remove PART NO. 1-4359 key. Remove spark plug wire from spark plug and secure away from plug. Engine and components are HOT. Avoid serious burns, allow all parts to cool before working on machine. Fuel Filler Cap and Vent must be closed securely to prevent fuel spillage. 3.4 SERVICE - ANNUALLY
ページ18に含まれる内容の要旨
Section 4 - ADJUSTMENTS & REPAIR 4.1.2. Neutral Return Spring Adjustments WARNING When the motion control levers are released, return DO NOT attempt any adjustments, maintenance, springs assist them back to the neutral position. See service or repairs with the engine running. Stop Figure 4.1a. To adjust spring tension: engine. Stop blade. Engage parking brake. Remove 1. If a stronger return is desired, tighten the nyloc key. Remove spark plug wire from spark plug and nut atop the
ページ19に含まれる内容の要旨
Section 4 - ADJUSTMENTS & REPAIR WARNING SPINDLE PULLEY SPINDLE PULLEY DO NOT attempt any adjustments, maintenance, service or repairs with the engine running. Stop engine. Stop blade. Engage parking brake. Remove key. Remove spark plug wire from spark plug and secure away from plug. Engine and components are HOT. Avoid serious burns, allow all parts to cool before working on machine. Fuel Filler Cap and Vent must be closed securely to prevent fuel spillage. IDLER PULLEY STATION
ページ20に含まれる内容の要旨
Section 4 - ADJUSTMENTS & REPAIR 4.3.5. BLADE BRAKE ADJUSTMENT WARNING The SNAPPER SCRAMBLER is equipped with an DO NOT attempt any adjustments, maintenance, electric clutch/brake that should stop blade rotation service or repairs with the engine running. Stop in 5 seconds or less after being turned off. If blades engine. Stop blade. Engage parking brake. Remove continue to rotate longer than 5 seconds, key. Remove spark plug wire from spark plug and adjustment or replacement is require
