ページ1に含まれる内容の要旨
WINE STORAGE
INSTALLATION INSTRUCTIONS
INSTRUCCIONES DE INSTALACIÓN
INSTRUCTIONS D’INSTALLATION
ISTRUZIONI PER L’INSTALLAZIONE
INSTALLATIONSANWEISUNGEN
ページ2に含まれる内容の要旨
SUB-ZERO WINE STORAGE The importance of the installation of the Sub-Zero Wine Storage unit cannot be overemphasized. Installation should be done by a qualified installer. Before you begin the installation process, CONTENTS it is recommended that you read this entire Installation Instructions book. There are key Models ICB424 and ICB424FS Installation 3 details that you should take special care to observe during the installation. By reading Models ICB427 and ICB427R Installation 12 these instr
ページ3に含まれる内容の要旨
MODELS ICB424 AND ICB424FS INSTALLATION MODELS ICB424 AND ICB424FS MODELS ICB424 ICB424FS SITE PREPARATION INSTALLATION SPECIFIC ATIONS The Sub-Zero Model ICB424FS wine storage TOP VIEW unit is designed to be attractive in a stand alone setting. It can also be slid into surround- 610 mm ROUGH ing cabinetry with clearance dimensions OPENING DEPTH slightly different than the standard built-in Model ICB424. Make sure that the finished rough opening ROUGH OPENING where the Wine Storage unit is to b
ページ4に含まれる内容の要旨
MODELS ICB424 AND ICB424FS INSTALLATION MODELS ELECTRICAL REQUIREMENTS UNPACKING AND MOVING ICB424 ICB424FS A 220-240 V AC, 50/60 Hz, 10 amp circuit Uncrate the unit, remove its wood base and breaker and electrical supply are required. A discard the shipping bolts that hold the wood separate circuit, servicing only this appliance, base to the bottom of the unit. Remove all is required. packing materials and tape. The power supply cord has a grounding plug, IMPORTANT NOTE: Do not discard the kic
ページ5に含まれる内容の要旨
MODELS ICB424 AND ICB424FS INSTALLATION ANTI-TIP BRACKET INSTALLATION MODELS ICB424 ICB424FS MODEL ICB424FS To prevent the unit from tipping forward If you are installing the Model ICB424FS in a and provide a stable installation, the unit space deeper than 625 mm, the anti-tip bracket must be secured in place with the anti-tip must be installed no more than 625 mm deep, bracket. so it engages the unit properly. It is important that this measurement be made from the front surface of the door, to
ページ6に含まれる内容の要旨
MODELS ICB424 AND ICB424FS INSTALLATION MODELS ANTI-TIP BRACKET INSTALLATION ICB424 ICB424FS WOOD FLOOR APPLICATIONS Installation for Concrete Wedge Anchors: 1) Drill a 10 mm diameter hole any depth Use the four #12 x 64 mm wood screws and exceeding the minimum embedment. the four 6 mm flat washers provided. Drill pilot Clean the hole or continue drilling addi- holes 5 mm diameter maximum, and be sure tional depth to accommodate drill fines. that the screws penetrate through the flooring Use a
ページ7に含まれる内容の要旨
MODELS ICB424 AND ICB424FS INSTALLATION LOCK INSTALLATION MODELS ICB424 ICB424FS IMPORTANT NOTE: If you are adding an If a home alarm system is to be used with the accessory lock kit to your Wine Storage unit, Wine Storage unit, the lead wires should be it should be installed before you position the threaded into the compressor compartment unit. Installation instructions are included with before you position the unit. See Home Alarm the lock kit. Connections on page 8, for the location of these
ページ8に含まれる内容の要旨
MODELS ICB424 AND ICB424FS INSTALLATION MODELS LEVEL THE UNIT HOME ALARM CONNECTIONS ICB424 ICB424FS Using an adjustable wrench or pliers, turn Before the kickplate is installed, all necessary each of the four leveling legs clockwise to raise wiring connections in the compressor compart- the unit and counterclockwise to lower the ment should be completed. unit. For the location of the leveling legs, see If a home alarm system is to be installed on illustration 6 below. the Wine Storage unit, the
ページ9に含まれる内容の要旨
MODELS ICB424 AND ICB424FS INSTALLATION KICKPLATE INSTALLATION DOOR PANELS – MODEL ICB424 MODELS ICB424 ICB424FS Once the unit is leveled and wiring connections Model ICB424 is offered in two design applica- made, the kickplate can be installed. Use the tions; stainless steel (/S) and overlay (/O). Each two #10 x 13 mm stainless steel screws that of these designs are available as a glass door are provided with the kickplate. Refer to illus- (G) model. tration 8 below. The stainless steel Model I
ページ10に含まれる内容の要旨
MODELS ICB424 AND ICB424FS INSTALLATION MODELS OVERLAY DOOR PANELS ICB424 ICB424FS OVERLAY GLASS DOOR – MODEL ICB424 IMPORTANT NOTE: After the first three or four mounting screws are in place, but not Inspect the door panel for the minimum 16 mm completely tightened, close the door and check thickness, the finished inside edge and the 5 kg your panel fit. This is the time to make small weight limit. See the Wine Storage section of adjustments. Once you are satisfied with the the Sub-Zero Design
ページ11に含まれる内容の要旨
MODELS ICB424 AND ICB424FS INSTALLATION HINGE ADJUSTMENT MODELS ICB424 ICB424FS IMPORTANT NOTE: Install screws in all the IMPORTANT NOTE: The Wine Storage unit mounting holes in the door frame. The nature must be installed and leveled before door of the door panel with a narrow outer rim and hinge adjustments can be made. no connecting center member requires the The top and bottom cabinet hinges on Models support provided by the glass door. ICB424 and ICB424FS are held in place with After the do
ページ12に含まれる内容の要旨
MODELS ICB427 AND ICB427R INSTALLATION MODELS MODELS ICB427 AND ICB427R ICB427 ICB427R INSTALLATION SPECIFIC ATIONS SITE PREPARATION Make sure that the finished rough opening where the Wine Storage unit is to be installed 635 mm is properly prepared. Refer to the Installation ROUGH Specifications illustration for rough opening OPENING DEPTH dimensions, door swing clearance and electri- cal placement for Models ICB427 and ICB427R. IMPORTANT NOTE: To operate properly, the TOP VIEW door must open
ページ13に含まれる内容の要旨
MODELS ICB427 AND ICB427R INSTALLATION ELECTRICAL REQUIREMENTS UNPACKING AND MOVING MODELS ICB427 ICB427R A 220-240 V AC, 50/60 Hz, 10 amp circuit Uncrate the unit, remove its wood base and breaker and electrical supply are required. A discard the shipping bolts that hold the wood separate circuit, servicing only this appliance, base to the bottom of the unit. Remove all is required. packing materials and tape. The power supply cord has a grounding plug, IMPORTANT NOTE: Do not discard the which
ページ14に含まれる内容の要旨
MODELS ICB427 AND ICB427R INSTALLATION MODELS ANTI-TIP BRACKET INSTALLATION ICB427 ICB427R WOOD FLOOR APPLICATIONS Use the six #12 x 64 mm wood screws and the To prevent the unit from tipping forward and provide a stable installation, install six 6 mm flat washers provided. Drill pilot the anti-tip bracket and extend the front holes 5 mm diameter maximum, and be sure leveling legs to the floor. that the screws penetrate through the flooring material and into the wall plate a minimum of 19 mm. Be
ページ15に含まれる内容の要旨
MODELS ICB427 AND ICB427R INSTALLATION POSITION THE UNIT MODELS ICB427 ICB427R Installation for Concrete Wedge Anchors: 1) Drill a 10 mm diameter hole any depth Before moving the Wine Storage unit into exceeding the minimum embedment. Clean position, secure the door closed. Remove the hole or continue drilling additional the drawers of the Model ICB427R. depth to accommodate drill fines. Use a OPTIONAL carbide drill bit. COMPONENTS IMPORTANT NOTE: For Model ICB427R, the 2) Assemble the washer an
ページ16に含まれる内容の要旨
MODELS ICB427 AND ICB427R INSTALLATION MODELS POSITION THE UNIT ICB427 ICB427R IMPORTANT NOTE: If you are adding an If a home alarm system is to be used with the accessory lock kit to your Model ICB427 or Wine Storage unit, the lead wires should be ICB427R, the catch should be installed at the threaded into the compressor compartment top of appliance cabinet before you position before you position the unit. See Other Wiring the unit. See Lock Installation on page 23. Connections on page 18 for t
ページ17に含まれる内容の要旨
MODELS ICB427 AND ICB427R INSTALLATION LEVEL THE UNIT MOLDING INSTALLATION MODELS ICB427 ICB427R Level the unit by turning the front leveling legs The decorative white molding strips for the clockwise to raise the unit, or counterclockwise side and top of Models ICB427 and ICB427R to lower it. To assist you in adjusting the front can be snapped into place. The top molding leveling legs up or down, use a standard piece must be installed before the side screwdriver blade and place it in the front
ページ18に含まれる内容の要旨
MODELS ICB427 AND ICB427R INSTALLATION MODELS OTHER WIRING CONNECTIONS ICB427 ICB427R Before the kickplate/grille is installed, all IMPORTANT NOTE: If you are not responsible necessary wiring connections in the compres- for alarm system connection, this information sor compartment should be completed. should be supplied to the home security system contractor. If the dual installation heater kit (#7007529) is used with Model ICB427 or ICB427R, the power OPTIONAL supply leads should be connected a
ページ19に含まれる内容の要旨
MODELS ICB427 AND ICB427R INSTALLATION KICKPLATE / GRILLE INSTALLATION MODELS ICB427 ICB427R Once the unit is leveled and wiring connec- Classic stainless steel panels—available as tions made, the kickplate/grille can be sales accessories—may be configured several installed. ways and are shipped separately. Stainless steel panels are shipped with matching IMPORTANT NOTE: The kickplate/grille must handles in place. be removed for servicing. The floor cannot PA N E L interfere with removal. The lo
ページ20に含まれる内容の要旨
MODELS ICB427 AND ICB427R INSTALLATION MODELS STAINLESS STEEL DOOR PANEL OVERLAY GLASS DOOR PANEL ICB427 ICB427R Before installing the stainless steel door panel, Inspect the door panel for the minimum 16 check the panel carefully. Options are available mm thickness, the greater width requirements for kickplate/grille height, overall height, door for the stiles (to cover the door hinges), and swing and door lock. the finished inside edge. The door panel has a weight limit of 9 kg. See the Wine S
