ページ1に含まれる内容の要旨
Safety Instructions & Operator’s Manual for
MID MOUNT Z-RIDER
ZERO TURNING
HYDRO DRIVE
SERIES 2
MODELS
NZM19482KWV
NZM21522KWV
NZM25612KWV
NZM27612KH
MODEL NUMBER EXPLANATION
N Z M 19 48 2 KWV
MODEL DESIGNATION ENGINE TYPE
DRIVE SYSTEM TYPE SERIES DESIGNATION
MOWER ORIENTATION MOWER DECK SIZE
ENGINE HP *
POWER UNIT
N – Model Designation 19.0 – Engine Horse Power 48 – 48” Mower Width 2 – Series Designation
Z – Zero Turning – Hydro Drive 21.0 -- Engine Horse
ページ2に含まれる内容の要旨
IMPORTANT SAFETY INSTRUCTIONS WARNING: This powerful cutting machine is capable of amputating hands and feet and can throw objects that can cause injury and damage! Failure to comply with the following SAFETY instructions could result in serious injury or death to the operator or other persons. The owner of the machine must understand these instructions and must allow only persons who understand these instructions to operate machine. Each person operating the machine must be of sound mind a
ページ3に含まれる内容の要旨
IMPORTANT SAFETY INSTRUCTIONS PREPARATION SAFE HANDLING OF GASOLINE (Continued From Previous Page) To avoid personal injury or property damage, use 2. Only mature, responsible persons shall operate or extreme care in handling gasoline. Gasoline is service the machine and only after proper instruction extremely flammable and the vapors are explosive and training. The owner is responsible for training the 1. Extinguish all cigarettes, cigars, pipes and other operators. Further, the owner/
ページ4に含まれる内容の要旨
IMPORTANT SAFETY INSTRUCTIONS OPERATION MAINTENANCE (Continued From Previous Page) (Continued From Previous Column) 8. Keep hands and feet away from rotating blades 6. Always provide adequate ventilation when running engine. Engine exhaust gases contain underneath deck. DO NOT place foot on ground carbon monoxide, an odorless and deadly while BLADES are ON or machine is in motion. poison. 9. DO NOT operate machine without entire grass 7. Disconnect battery before performing cat
ページ5に含まれる内容の要旨
TABLE OF CONTENTS IMPORTANT SAFETY INSTRUCTIONS ........................................................................2-4 TABLE OF CONTENTS ..................................................................................................... 5 SECTION 1 - FAMILIARIZATION ...................................................................................... 6 SECTION 2 –SAFETY MESSAGES AND SYMBOLS....................................................7-8 SECTION 3 - OPERATING INSTRUCTIONS .
ページ6に含まれる内容の要旨
Section 1 - FAMILIARIZATION HOUR KEY METER SWITCH BLADE CHOKE ENGINE SPEED CONTROL SWITCH CONTROL MOTION CONTROL LEVER OPERATOR’S SEAT LEFT HAND FUEL TANK RIGHT HAND FUEL TANK MOTION CONTROL LEVER PARKING DECK LIFT BRAKE LEVER LEVER CONTROL PANEL (SEE INSET) DISCHARGE DEFLECTOR IMPORTANT The figures and illustrations in this manual DECK LIFT PEDAL are provided for reference only an
ページ7に含まれる内容の要旨
Section 2 – SAFETY MESSAGES AND SYMBOLS DANGER ! ROTATING PARTS KEEP AWAY FROM MOVING PARTS MOTION CONTROL LEVER OPERATION PARKING BRAKE LEVER OPERATION WEAR HEARING PROTECTION WARNING ! AVOID SERIOUS INJURY OR DEATH STARTING, OPERATION & STOPPING OF MACHINE 7
ページ8に含まれる内容の要旨
Section 2 – SAFETY MESSAGES AND SYMBOLS RUN OFF/STOP START PULL SWITCH “UP” TO ENGAGE BLADES PUSH SWITCH “DOWN” TO KEYSWITCH HOUR METER DISENGAGE BLADES FAST CONTROL PANEL IDENTIFICATION SLOW CHOKE CONTROL ENGINE SPEED CONTROL DANGER! ROTATING BLADES KEEP CHILDREN AND OTHERS OUT OF MOWING AREA STOP RUN START DANGER! ROTATING BLADES IGN
ページ9に含まれる内容の要旨
Section 3 - OPERATING INSTRUCTIONS 3.1 PRE-START CHECK LIST 3.1.8. Place mower in desired cutting height Make the following checks and perform the service setting. Grasp deck lift lever and depress release required before each start-up. latch located underneath the lever. Move lever to 3.1.1. Check tires and add or release air as needed desired cutting height setting and release latch. to bring pressure to 12 psi in drive tires. Pressure in Insert stop pin to desired cutting height. fron
ページ10に含まれる内容の要旨
Section 3 - OPERATING INSTRUCTIONS ROLL RELEASE: To roll the machine without the 3.2 STARTING & STOPPING – ENGINE, BLADES, engine running, pressure within the hydraulic pumps PARKING BRAKE must be released. There is a hydraulic pressure relief This machine is equipped with dual hydrostatic wheel valve on the upper side of each pump that is used to drive transmissions. Each hydro pump is controlled by a release the pressure. Use a wrench to rotate both relief separate motion control l
ページ11に含まれる内容の要旨
Section 3 - OPERATING INSTRUCTIONS 3.2.1. STARTING ENGINE 3.2.5. PARKING BRAKE NOTE: If after 5 seconds of cranking the engine 1. Engage parking brake by pulling the parking does not start, release the key. Attempt starting brake lever back to the engaged position. See again after waiting for approximately 20 seconds. Figure 3.7. 7. After engine starts, move the choke control to NOTE: Engaging parking brake prior to placing the “OFF” or no choke position. Allow a brief motion control le
ページ12に含まれる内容の要旨
Section 3 - OPERATING INSTRUCTIONS 3.3 CUTTING HEIGHT ADJUSTMENT 1. Adjust cutting height, as desired, to any position, using deck lift lever. The release latch should be pulled up when lowering the deck. When raising the deck, the release latch does not have to be pulled up. IMPORTANT: There is a foot assist pedal located to the right front side of the footrest. Always 6 HOLE POSITIONS FOR STOP PIN use this assist pedal to raise or lower the deck to the desired cutting he
ページ13に含まれる内容の要旨
Section 3 - OPERATING INSTRUCTIONS 3.4.2. STOPPING MACHINE 3.5 SAFETY INTERLOCK SYSTEM CHECKS This machine is equipped with an electrical safety 1. Return motion control lever to the neutral position & the neutral lock position. interlock system that is provided for the safety of the operator and others. All safety devices must be in place IMPORTANT: Operator must use hand assistance to bring both motion control levers to the neutral and functioning properly before operating the machine
ページ14に含まれる内容の要旨
Section 4 - MAINTENANCE 4.1 INTRODUCTION 4. Fill engine crankcase with new oil. Refer to your To retain the quality of the SNAPPER mower, use engine owner’s manual for oil specifications. genuine SNAPPER replacement parts only. Contact 5. Change engine oil filter at every oil change. a local SNAPPER dealer for parts and service Refer to your engine owner’s manual for service assistance. For the correct part or information for a instructions. particular SNAPPER mower, always mention
ページ15に含まれる内容の要旨
Section 4 - MAINTENANCE 4.2.3. CHECK MOWER DRIVE BELT 4. Clean Mower Deck 1. Lower deck to lowest setting. a. Remove key from ignition switch. 2. Remove footrest. See Figure 4.3. b. Remove spark plug wire(s) and secure away 3. Removal of footrest will allow access to deck from spark plug(s). belt. c. Raise mower deck to its highest setting. It may 4. Check the belt tension. The idler pulleys and be necessary to raise mower deck higher using a springs provide proper belt tension and requ
ページ16に含まれる内容の要旨
Section 4 - MAINTENANCE 4.3.3. RIDING MOWER - LUBRICATION 1. Front Wheel Bearings HYDRAULIC FLUID RESERVOIRS Lubricate with Kendall NLGI No. 2 lithium grease or equivalent, from a grease gun. See Figure 4.5. FRONT WHEEL FIGURE 4.6 LUBRICATE BEARINGS FIGURE 4.5 2. Hydro Pumps Check the level of the fluid in both of the fluid reservoirs. Wipe away all dirt and debris from around reser
ページ17に含まれる内容の要旨
Section 4 - MAINTENANCE 4.6 DECK REMOVAL WARNING Move power unit/mower deck to an area where the mower deck is to be disconnected. Turn engine Allow engine to cool for at least ten minutes before “OFF” and remove key from switch. Remove spark performing service or maintenance. DO NOT smoke plug wire(s) and secure away from spark plug(s). near fuel components when performing service or Move motion control levers to the neutral position. maintenance. DO NOT perform service and Engage
ページ18に含まれる内容の要旨
Section 4 - MAINTENANCE 6. Remove deck drive belt from around deck pulley. WARNING 7. Remove bolts and nuts to disconnect both stabilizers DO NOT attempt any maintenance, adjustments or from mower deck and power unit. See Figure 4.12 & service with engine running. STOP engine. STOP Figure 4.13. blades. Set parking brake. Remove key. Remove spark plug wires and secure away from spark plugs. Engine and components are HOT. Avoid serious burns, allow sufficient time for all
ページ19に含まれる内容の要旨
Section 5 - ADJUSTMENTS & REPAIR DANGER Exercise EXTREME CAUTION when making this REMOVE MOTION CONTROL adjustment, due to close proximity of moving parts. LEVER CONNECTING ROD 5.1 NEUTRAL POSITION ADJUSTMENTS The motion control levers control the movement and stopping of the machine. Move the control levers to the center or neutral position to stop machine. IMPORTANT: Always return both motion control levers with hand assistance to the neutral positi
ページ20に含まれる内容の要旨
Section 5 - ADJUSTMENTS & REPAIR 5.1 NEUTRAL POSITION ADJUSTMENTS 5.2 MOWER DECK & COMPONENT ADJUSTMENTS The leveling procedures for the 61 deck differ from (Continued From Previous Page) 12. With motion control levers remaining in the the 48 and 52 decks. The 61 deck replaces the two rear eyebolts with slotted brackets, and uses 1 1/4” neutral lock position, See Figure 3.7, hold connecting rod up to the activation assembly and check length of leveling blocks in place of the 1” blocks
