ページ1に含まれる内容の要旨
Safety Instructions & Operator’s Manual for
EUROPEAN
REAR ENGINE RIDING MOWER
SERIES 19
MODEL
EM250819BE
EM281019BE
MODEL NUMBER EXPLANATION
E M 28 10 19 B E
EUROPEAN MODEL ENGINE OPTIONS
MIDDLE MARKET ENGINE TYPE
CUTTING WIDTH SERIES DESIGNATION
ENGINE HP
E - European Model 25 - 25” Cutting Deck 08 - 8.0 HP Engine 19 - Series B - Briggs Engine E - Electric Start
M - Middle Market 28 - 28” Cutting Deck 10 - 10.0 HP Engine Designation
ページ2に含まれる内容の要旨
IMPORTANT SAFETY INSTRUCTIONS WARNING: This powerful cutting machine is capable of amputating hands and feet and can throw objects that can cause injury and damage! Failure to comply with the following SAFETY instructions could result in serious injury or death to the operator or other persons. The owner of the machine must understand these instructions and must allow only persons who understand these instructions to operate machine. Each person operating the machine must be of sound mind
ページ3に含まれる内容の要旨
IMPORTANT SAFETY INSTRUCTIONS PREPARATION OPERATION (Continued From Previous Page) (Continued From Previous Column) 7. Keep people and pets out of mowing area. 14. Exercise CAUTION when pulling loads. Limit Immediately STOP blades, STOP engine, and loads to those you can safely control and attach STOP machine if anyone enters the area. loads to hitch plate as specified with SNAPPER 8. Check shields, deflectors, switches, blade attachment instructions. controls and other safety devic
ページ4に含まれる内容の要旨
TABLE OF CONTENTS IMPORTANT SAFETY INSTRUCTIONS ................................................2-3 TABLE OF CONTENTS.............................................................................4 SECTION 1 - FAMILIARIZATION...........................................................5-7 Decals / Symbols.........................................................................................................6-7 SECTION 2 - OPERATING INSTRUCTIONS.......................................8-13 Pre
ページ5に含まれる内容の要旨
Section 1 - FAMILIARIZATION FUEL FILLER CAP VENT OPERATOR’S FUEL TANK SEAT STEERING WHEEL ENGINE SPEED CONTROL REAR BUMPER DECK LIFT LEVER CLUTCH/BRAKE PEDAL TRANSMISSION SHIFT LEVER MOWER BELT COVER DISCHARGE DEFLECTOR BLADE LEVER BLADE PEDALS PARK BRAKE MOWER LATCH DECK FIGURE 1.1 1.1 INTRODUCTION 1.2 NOMENCLATURE This manual has been prepared for the operator’s of the The nomenclature drawing above, Figure 1.1, shows the SNAPPER Rear E
ページ6に含まれる内容の要旨
Section 1 – FAMILIARIZATION – DECALS / SYMBOLS KEY SWITCH BLADE ENGAGED ON POSITION POSITION SYMBOLS “ON” START ENGINE OFF BLADE LEVER POSITION SYMBOLS BLADE DISENGAGED POSITION “OFF” ENGINE SPEED CONTROL SYMBOLS EUROPEAN COMMUNITY DECAL 29776 CHOKE POSITION CHUTE WARNING DECAL RABBIT 29784 “FAST” EUROPEAN NOISE CONTROL DECAL 23009 ENGINE SPEED CONTROL PATENT NUMBERS D
ページ7に含まれる内容の要旨
Section 1 – FAMILIARIZATION – DECALS / SYMBOLS LOWEST TRACTION HEIGHT OF CLUTCH CUT BATTERY CAUTION DECAL - 15691 PARK BRAKE HIGHEST CLUTCH/BRAKE HEIGHT OF DECAL - 2-8514 CUT HEIGHT OF CUT DECAL - 46218 AUTOMATIC BLADE STOP DECAL - 24072 BATTERY STORAGE DECAL - 29948 SAFETY INSTRUCTION DECAL - 35974 BATTERY CAUTION DECAL - 29947 CLUTCH/BRAKE, FAST TRANSMISSION SHIFT P
ページ8に含まれる内容の要旨
Section 2 - OPERATING INSTRUCTIONS 2.1 PRE-START CHECK LIST 2.2 OPERATOR’S SEAT ADJUSTMENT Make the following checks and perform the service 2.2.1. FRONT TO REAR ADJUSTMENT required before each start-up. 2.1.1. Check tires and add or release air as needed 1. With the engine stopped, loosen the two adjusting to bring pressure to 12 psi in front and 12 psi in rear knobs and move seat to desired position. After tires. adjustment, tighten knobs securely. If seat does not 2.1.2. Check
ページ9に含まれる内容の要旨
Section 2 - OPERATING INSTRUCTIONS 2.3 STARTING & OPERATION TO START ENGINE, 2.3.1. ENGINE (ELECTRIC START) PUSH CLUTCH/BRAKE IMPORTANT: When the ignition key is turned to PEDAL ALL THE WAY “START”, the engine will turn over, but will not start DOWN unless the Clutch/Brake pedal is pressed all the way down, the Blade Lever is in the “Off” position (See Figure 2.5).The operator should be in the seat. Start engine as follows: 1. Move transmission shift lever to (N) Neutral position
ページ10に含まれる内容の要旨
Section 2 - OPERATING INSTRUCTIONS 2.3 STARTING & OPERATION 5. Move engine speed control to the choke position 2.3.1. ENGINE (ELECTRIC START) (Continued) to start a cold engine. See Figure 2.6 8. Should the battery be too weak to start the engine, 6. Turn key to “ON” position. See Figure 2.9. Refer to Section “ENGINE (MANUAL START)” to manually start the electric start engines. 2.3.2. ENGINE (MANUAL START) IMPORTANT: When the ignition key is turned to “RUN”, and the recoil handle
ページ11に含まれる内容の要旨
Section 2 - OPERATING INSTRUCTIONS WARNING WARNING Once blade is disengaged, it should come to a DO NOT operate blades in reverse. STOP BLADES. complete stop in 3 seconds or less. If the blade LOOK and SEE behind and down for children, pets continues to rotate after 3 seconds, the blade brake and hazards before and while backing. must be adjusted. Refer to Section “BLADE BRAKE DEPRESS ADJUSTMENT” for adjustment procedures or return CLUTCH/BRAKE machine to an authorized SNAPPER deal
ページ12に含まれる内容の要旨
Section 2 - OPERATING INSTRUCTIONS WARNING DO NOT leave machine with engine running. Stop CLUTCH/BRAKE engine. Stop blade. Shift to neutral. Engage parking PEDAL brake. Remove key. 2.4 STOPPING - ENGINE, WHEEL DRIVE, BLADE 2.4.1. ENGINE 1. Stop engine by turning key to the “OFF” position. See Figure 2.13. TURN TO “OFF” POSITION PARK BRAKE LATCH SHOWN ENGAGED KEY FIGURE 2.14 BLADE LEVER (SHOWN IN “OFF” POSITION) FIGURE 2.13 BLADE PEDALS 2.4.2. WHEEL DRI
ページ13に含まれる内容の要旨
Section 2 - OPERATING INSTRUCTIONS 2.4 STOPPING - ENGINE, WHEEL DRIVE, BLADE 2.5. CUTTING HEIGHT ADJUSTMENT 2.4.4. PARK BRAKE 1. Adjust cutting height as desired to any one of 1. Engage park brake by pushing clutch/brake pedal five positions using deck lift lever. Move deck lift lever up or down to desired cutting height and then “DOWN” and moving the park brake latch to the move over to secure in the height of cut notch. “ENGAGED” position. While holding the park brake latch “ENGA
ページ14に含まれる内容の要旨
Section 3 - MAINTENANCE 5. After all the oil has drained, close the drain and WARNING wipe up any oil that may have spilled. See Figure 3.1. DO NOT attempt any adjustments, maintenance, service Dispose of used oil properly. or repairs with the engine running. Stop engine. Stop 6. Fill engine crankcase with new oil. Refer to your blade. Engage parking brake. Remove key. Remove engine owner’s manual for oil specifications. spark plug wire from spark plug and secure away from plug.
ページ15に含まれる内容の要旨
Section 3 - MAINTENANCE WARNING ENGINE PULLEY DO NOT attempt any adjustments, maintenance, service or repairs with the engine running. Stop engine. Stop blade. Engage parking brake. Remove key. Remove spark plug wire from spark plug and secure away from plug. Engine and components are HOT. Avoid serious burns, allow all parts to cool BELT SPACING before working on machine. Fuel Filler Cap and Vent SHOULD BE must be closed securely to prevent fuel spillage. 1-1/4” 3.2 SERVICE -
ページ16に含まれる内容の要旨
Section 3 - MAINTENANCE 3.3.3. MOWER DECK LEVELNESS 3.2.7. INTERLOCK SYSTEM Check mower deck for proper level. Adjust as Check interlock controls for proper function: required. Refer to Section “MOWER DECK The engine MUST NOT start if: ADJUSTMENT – LEVELNESS”. 1. Blade Control is “ON” and/or clutch/brake pedal is released. 3.3.4. CLEAN MOWER DECK The engine and blades MUST STOP if: 1. Follow WARNING statement found on this page. 2. The operator leaves the operator position with
ページ17に含まれる内容の要旨
Section 3 - MAINTENANCE 3.3 SERVICE - EVERY 25 OPERATING HOURS LEFT REAR AXLE (Continued from previous page) BEARING GREASE 3.3.7. FRONT WHEEL BEARING - LUBRICATION FITTING 1. Lubricate front wheel bearings with five shots of general purpose grease, from grease gun. See Figure 3.6. FRONT WHEEL GREASE FITTING FIGURE 3.7 3.3.9. DIFFERENTIAL/CHAIN CASE - LUBRICATION 1. Stand rear engine rider on its rear bumper and FIGURE 3.6 check the fill/level plug, for cracks and we
ページ18に含まれる内容の要旨
Section 3 - MAINTENANCE 3.4 SERVICE - ANNUALLY WARNING 3.4.1. Perform all maintenance as specified in DO NOT attempt any adjustments, maintenance, “MAINTENANCE SCHEDULE” Section of this manual. service or repairs with the engine running. Stop engine. Stop blade. Engage parking brake. Remove 3.4.2. ENGINE key. Remove spark plug wire from spark plug and Perform all maintenance as specified in Engine secure away from plug. Engine and components are Owner’s Manual. HOT. Avoid seriou
ページ19に含まれる内容の要旨
Section 3 - MAINTENANCE 3.7 REMOVING FUEL TANK WARNING Before removing fuel tank from rear engine rider, DO NOT attempt any adjustments, maintenance, move rider outdoors where fumes can be easily service or repairs with the engine running. Stop dissipated. Removal of the tank is accomplished engine. Stop blade. Engage parking brake. Remove from the left side of the machine by pulling the tank key. Remove spark plug wire from spark plug and straight up and away from the fuel tank br
ページ20に含まれる内容の要旨
Section 4 - ADJUSTMENTS & REPAIR WARNING DO NOT attempt any adjustments, maintenance, service or repairs with the engine running. Stop engine. Stop blade. Engage parking brake. Remove key. Remove spark plug wire from spark plug and secure away from plug. Engine and components are FLAT HOT. Avoid serious burns, allow all parts to cool WASHERS before working on machine. Fuel Filler Cap and Vent must be closed securely to prevent fuel spillage. HAIRPIN FRAME 4.1 ENGINE ADJUSTMENTS
