ページ1に含まれる内容の要旨
P300
Cod. 2850012 - Rev. 00 ENG - Ottobre 2008
ページ2に含まれる内容の要旨
INDEX ELECTRIC CIRCUIT LEGEND F anti-interference filter Technical characteristics ----------------------- 3 TR transformer 230Vac / 24 – 20 Vac 170VA I.P. door safety switch Installation ---------------------------------------- 4 CX safety thermostat 145°C Operating ----------------------------------------- 7 R.C. boiler heating element 230V 1200W R.G. espresso group heating element Programmation----------------------------------- 8 V ventilator frequent menu ------------------
ページ3に含まれる内容の要旨
ELECTRIC DIAGRAM TECHNICAL CHARACTERISTICS Dimensions: Height 162 cm Width 48.5 cm Depth 55 cm Weight: 90 Kg Voltage supply: 230 Vac. 50 Hz or 120 Vac. 60Hz on request Absorbed power: 1,6 KW Selections: n°14 for F300 model n°28 for F306 model Possibility to program up to 40 selections. Payment system: predisposed for • Obliterator / token system 24Vdc • Parallel selector 12Vac or 24Vac • Executive / MDB system Water connection: inside tank 15lit.
ページ4に含まれる内容の要旨
HYDRAULIC CIRCUIT INSTALLATION Before proceeding to the operations of installation, maintenance and reparation of the machine, read the manual carefully, where there is contained the necessary information for the correct use of the machine. Install the machine in a dry and not dusty place. Put to level the machine through the regulation of the feet. ELECTRIC CONNECTION Before connecting the machine to the power, follow the following instructions: o check that the el
ページ5に含まれる内容の要旨
HYDRAULIC CONNECTION TROUBLESHOOTING GUIDE INSIDE TANK The machine is provided with a program of self-diagnosis, that allows to visualize on the display the messages of breakdown or machine stopped : The machine is already set for the inside tank working. Message Description Probable cause WATER SYSTEM CONNECTION (OPTIONAL) during the cup-releasing, the board has not Fuses, cup-releaser motor, cup-releaser micro ERR. CUP-RELEAS. received the change of state of the cup-
ページ6に含まれる内容の要旨
PRODUCTS LOADING QUICK FUNCTIONS Fill up the containers of the products as the labels on them. In this section, it is possible to perform some of the most useful functions by the operator. CUPS LOADING To access press the button “QUICK MENU” of the keyboard. Rotate the cup container towards left and open the cover slightly lifting it. Load the cup columns, assuring that the two columns are jammed by the magnets. On display you will see “QUICK MENU” Close the cover
ページ7に含まれる内容の要旨
Movements nr 38 and 39 (Decounter coffee and OPERATING chocolate) After have followed all the instructions of installation, it is possible to turn on the machine through the light switch situated on the rear side. The movements nr38 (decounter coffee) and nr39 (decounter chocolate), where inserted, decrease the relative decounter by a unit. At the switch on of the machine, it appears on display for a brief time the message To set the value of the decounter, it is enough to chang
ページ8に含まれる内容の要旨
26 TIME SOLUB.5 The machine makes the soluble 5 cycle with time control. PROGRAMMING 27 UNHOOK CUP The cup-arm goes in “cup” position and the cup-dispenser (turrets type) releases a cup”. 28 SEARCH CUP A cup searching (turrets type) happens. 29 ON TIME WATER A hot water quantity (in seconds) is supplied. There are 2 levels of program: a frequent menu and a main menu. 30 SOLUBLE 6 The machine makes the soluble 6 with volumetric control. 31 TIME SOLUBLE 6 The machine makes the soluble
ページ9に含まれる内容の要旨
It is possible to eliminate, modify or insert movements or to change its regulations SET DRINKS where possible, for example the dosing of the products. Entering the program through D, you will see the sequence of the existing drink • to move the selection cursor movement use A and B codes. • to insert a new movement in the selected position press “2” • to eliminate the selected movement press “1” 11-12-13-14-15-1 • to modify the selected movement press" 3" Sel.11 • to
ページ10に含まれる内容の要旨
To modify the name of the drink use the keys: SET DRINKS " 1" to withdraw with the cursor on the character " 2" to advance with the cursor on the character Premise: every selection or drink is composed by a sequence of movements which "A" or" B" to modify the character correspond to a single operation of the machine. The single movements are only performed after the correct event of the previous Example: change the water quantity of the coffee of the selection “ long coffee
ページ11に含まれる内容の要旨
BOILER 1 WORKING COUNTERS & AMOUNTS Enable of the boiler 1. In this menu it is possible to notice the counters of the various selections and BOILER 2 WORKING eventually to reset them. Enable of the boiler 2. Press D to enter the menu that is composed in the following way: Nota 1: to avoid the blocks in the mixing group, the software controls the powder and water values in the way explained in the diagram. TOTAL COUNTERS&AMOUNTS total in normal working of counters
ページ12に含まれる内容の要旨
SET FILTER COUNTER EVENTS Counter for the limestone filter substitution. Once reached, the machine will show “*” on display but it will continue to work (see also at page 27). In this menu it is possible to notice the last 100 events of the machine. Entering the menu with D the following data will be visualized: SET NUMBER OF COFFEE GROUNDS Counter for coffee grounds emptying. Once reached, the machine will DATA: time & date show “EMPTY GROUNDS” and it will stop (see also at
ページ13に含まれる内容の要旨
E113 boiler 1 temperature OPTIONS: LEVEL 2 (manager- technician) E114 boiler 2 temperature E115 coffee grounds counter After have inserted the correct password, that it initially is "222", you will enter E116 boiler 1 off by timer the following menu: E117 boiler 2 off by timer E118 boiler 1 heating MODIFY PASSWORD LEVEL 1 E119 “executive or MDB” communication during working Insert the new password and press D to confirm. E120 “executive or MDB” communication at power on E121
ページ14に含まれる内容の要旨
MAIN MENU OPTIONS: LEVEL 1 (operator) After have inserted the correct password, which initially is "111”, the following To access this menu, keep pressed the button PROG for 5 seconds. menu will appear: The menu is composed by the followings programs: MODIFY PASSWORD LEVEL 1 Insert the new password and press D to confirm. SET TIME Setting of the clock and the schedules of some functions. TEST MACHINE MODE Set the machine in Test mode working. PAYMENT SYSTEM Setting of th
ページ15に含まれる内容の要旨
OPTIONS SET TIME This menu is constituted by 2 different levels which are protected by a password: To enter this menu, press D: 1st level: Operator - dedicated to the operator of the machine SET DATE AND HOUR 2nd level: Management - dedicated to the technician / manager of the machine Date and clock setting. The access to the first level is also possible from the 2nd level. TIMER ON/OFF BOILER 1 Set the period of inactivity of boiler 1. The machine has 3 kinds of working w
ページ16に含まれる内容の要旨
PAYMENT SYSTEM SET TEMPERATURE The followings programs compose this menu: The followings programs compose this menu: SET COIN VALUE PARALLEL SYSTEM SET BOILER 1 TEMPERATURE Setting of the coin values (see note 1). Set-up of the boiler 1 temperature. TIME 1ST PRICE PERIOD SET BOILER 2 TEMPERATURE Setting of the period 1 during which you can apply a discount. Set-up of the boiler 2 temperature (if present). 1ST PRICE-PERIOD DISCOUNT TIME OVERHEATING BOILER 1 Value of disco
