ページ1に含まれる内容の要旨
SERVICE/INSTALLATION MANUAL
HOTEL/MOTEL DISPENSER
GC Series Cuber Shown
CD10022
CD10522
ICE Series Cuber Shown
CD20030
CD20530
ICE-O-Matic
11100 East 45th Avenue
Denver, Colorado, USA 80239
Part Number 80701101 Print Date: 6/00
ページ2に含まれる内容の要旨
ページ3に含まれる内容の要旨
CD10022 CD20030 CD10522 CD20530 Introduction To the owner or user. This product is a source of information about the installation, start up, cleaning, maintenance and repair of the product. The CD10022, CD10522, CD20030 and CD20530 are Ice-O-Matics brand hotel/motel ice dispenser. The CD10022 is designed to use a Ice-O-Matic model GC300, 550, ECP 400, 550, 556 ice machine as the source for ice. The CD-200-30 is designed to use a Ice-O-Matic model ICE 250, 400, 500 and 600 ice machine as the sour
ページ4に含まれる内容の要旨
CD10022 CD20030 CD10522 CD20530 Specifications Limitations: • Must meet the same limitations as the cuber installed on top of it: o 50 F air minimum o 100 F air maximum Must be installed indoors Must allow space to the right for air intake when using air cooled machine. The CD10022 and CD10522 are compatible only with Ice-O-Matics’ models GC 300, 550, ECP 400, 550, 556. The CD20030 and CD20530 are compatible only with Ice-O-Matics’ models ICE 250, 305, 400, 500, 600. Must allow spa
ページ5に含まれる内容の要旨
CD10022 CD20030 CD10522 CD20530 Installation: General After the carton has been removed from the dispenser, the legs may be installed. NOTE Remove any packaging material Place flat portions of the carton on the floor from inside the storage bin. Retain keys for later use. behind the dispenser and lay the dispenser Check that gasket tape is on the down on its back. top outside edge of the dispenser where the ice machine will rest. Thread the legs into the base of the dispenser. Be sure that the l
ページ6に含まれる内容の要旨
CD10022 CD20030 CD10522 CD20530 Installation: Ice Machine Check that gasket tape has been placed at the outside edge of the dispenser top. Place corner posts from the carton on top of the dispenser, at the left and right corners. Place the ice machine onto the dispenser. The ice machine is heavy, use of a mechanical hoist is recommended. Carefully remove cardboard supports and allow ice machine to rest on dispenser gasket. Follow all instructions for installation of the ice machine. 4
ページ7に含まれる内容の要旨
CD10022 CD20030 CD10522 CD20530 Kits: Coin Mechanism Kits are available to install a coin mechanism, a room key mechanism or a key card mechanism. 8. Mount the timer and relay from the All kits come with detailed instructions which kit in the control box. (See typical are also listed below. layout of the parts in the following page). Please follow these instructions carefully to 9. Remove wires #8 and #9 from the complete the addition of the coin mechanism control box. These wires will be re- ki
ページ8に含まれる内容の要旨
CD10022 CD20030 CD10522 CD20530 Kits: Coin Mechanism 15. Replace the control box cover, front brace and decorative front cover. The dispenser should now be restored to service. 6
ページ9に含まれる内容の要旨
CD10022 CD20030 CD10522 CD20530 Key Kit Installation This kit has been designed for use with the 5. With a key in place, adjust the snap CD10022, CD10522, CD20030 and CD20530 ice dis- action of the micro switch so that it penser. When this kit is installed, ice cannot be dis- actuates when the key is inserted. pensed unless a specific type of key is inserted into the lock cylinder. The kit contains a universal mount- Now disconnect wire #8 and #9 from ing fitting for lock cylinders and a switchi
ページ10に含まれる内容の要旨
CD10022 CD20030 CD10522 CD20530 Key Kit Installation The operation of this kit is as follows: When the key is inserted into the lock cylinder, a portion of the key will extend beyond the brass fitting. It is this part of the key that will actuate the kit micro switch. Then when the dispense button swithch is depressed and held; the machine will dispense ice. 8
ページ11に含まれる内容の要旨
CD10022 CD20030 CD10522 CD20530 Key Card Kit Installation This kit has been designed for use with the CD10022, CD10522, CD20030 and CD20530 ice dispenser. When this kit is installed, ice cannot be dispensed unless a key card is inserted into the key card slot. The kit contains a universal mounting and a microswitch assembly. Electrical shock hazard. Electrical shock can cause personal injury. Disconnect power before begining to service components. 1. Make sure all electrical power is disconnecte
ページ12に含まれる内容の要旨
CD10022 CD20030 CD10522 CD20530 Key Card Kit Installation The Operation of this kit is as follows: When the key card is inserted into the key card slot, and the dispenser button switch is depressed and held, the machine will dispense ice.. 10
ページ13に含まれる内容の要旨
CD10022 CD20030 CD10522 CD20530 Final Check List/Initial Start Up 1. Check that electrical power has been supplied. Electrical Sequence: 2. Check that a drain, separate from the ice Pushing the dispenser switch closes the machine, insulated and made of rigid tubing, contacts to the gearmotor and to the has been connected to the dispenser. ice door solenoid. The ice door solenoid will open and the dispensing wheel will 3. Check that the ice machine has been properly start to turn bringing ice to
ページ14に含まれる内容の要旨
CD10022 CD20030 CD10522 CD20530 Operational Schematic 12
ページ15に含まれる内容の要旨
CD10022 CD20030 CD10522 CD20530 Cleaning sweep arm securing the wheel to the General Care and Ceaning: drive shaft. Remove the sweep arm by rotating it in the counter clockwise Periodically inspect and clean the ice dispenser direction. to keep it operating at peak performance. 6. Pull the wheel off the drive shaft and Wash the outside of the dispenser with warm leave it in the dispenser. water and soap. Rinse off and dry. 7. Mix a solution of 5 ounces of ice Cleaning and Sanitizing of the Ice m
ページ16に含まれる内容の要旨
CD10022 CD20030 CD10522 CD20530 Cleaning 10. Mix a solution of ice machine sanitixer and water: 1 ounce of household bleach to 2 gallons of o o (95 F-115 F) water. Wash all interior surfaces and the wheel withthe sanitizer solution. Use a clean cloth. 11. Allow the parts to air dry. 12.Reassemble wheel and sweep arm onto drive shaft. 13. Replace all panels. 14. Reconnect power, be sure ice machine is switched back on. 14
ページ17に含まれる内容の要旨
CD10022 CD20030 CD10522 CD20530 Service Diagnosis PROBLEM POSSIBLE CAUSE PROBABLE FIX Does not vend No ice Check ice machine No power Check power supply Vend switch open Check / replace vend switch Sink interlock switch open Check / replace sink interlock switch Ice jams in chute Machine is not level Front panel not on all the way Reinstall panel Gear motor open Check/replace gearmotor Relay does not operate Check wiring Check power to relay Check for burnt contacts Check for power to solenoid I
ページ18に含まれる内容の要旨
CD10022 CD20030 CD10522 CD20530 Removal and Replacement Dispense Wheel: 1. Remove all of the ice stored inside Electrical shock hazard. the dispenser bin and shut off the Electrical shock can ice maker. cause personal injury. Disconnect power before 2. Disconnect the electrical power. begining to service components. 3. Remove ice machine from dispenser. 4. Remove large dispenser top panel. 5. Reach into opening, locate the Gear Motor: sweep arm which secures the wheel to the drive shaft. Remove
ページ19に含まれる内容の要旨
CD10022 CD20030 CD10522 CD20530 Standard With Room Key Kit or Card Kit Electrical Schematic 17
ページ20に含まれる内容の要旨
CD10022 CD20030 CD10522 CD20530 Standard With Room Key Kit or Card Kit Electrical Schematic 18
