ページ1に含まれる内容の要旨
OPERATOR’S MANUAL
MODEL STT-31BSG
PART NUMBER 03093
ページ2に含まれる内容の要旨
WARNING:
ページ3に含まれる内容の要旨
TABLE OF CONTENTS SUBJECT PAGE Section 1 - General Information
Section 2 - Safety Informati
ページ4に含まれる内容の要旨
TABLE OF CONTENTS (CONT'D) SUBJECT PAGE Section 6 - Adjustments ( .- $-23 , ( 23 , ( -23 (" $23
ページ5に含まれる内容の要旨
Section 1 GENERAL INFORMATION &
1.1 INTRODUCTION
)
! "#$%% #$&
ページ6に含まれる内容の要旨
- ! 2 3 1 SYMBOL DESCRIPTION SYMBOL DESCRIPTION 21 % 1 6 1 6
48071S 45 %
45 4
WARNING &
0 FALLING HAZARD USE ONLY SCAG APPROVED RIDING ATTACHMENTS 481109 SEE OPERATOR'S MANUAL 2
ページ7に含まれる内容の要旨
SYMBOL DESCRIPTION SYMBOL DESCRIPTION
& 2
(6
2
7
(- 2
( 481039S 5
4 2
(" + 4 8 3
%4 0 96 $ 3
ページ8に含まれる内容の要旨
Section 2 SAFETY INFORMATION 2.1 INTRODUCTION
%
*"$?@ +,
2
0
0
1
ページ9に含まれる内容の要旨
Section 2 2.3 BEFORE OPERATION '=
$
CONSIDERATIONS (CONT'D)
:
" '' 9
B C /
!
1
1
#
ページ10に含まれる内容の要旨
Section 2 '< " 2.4 OPERATION CONSIDERATIONS (CONT'D) 'A %
< %
1
A # ':
ページ11に含まれる内容の要旨
Section 2 2.6 SAFETY AND INSTRUCTIONAL DECALS WARNING INSTALL BELT COVER BEFORE OPERATING MACHINE READ OPERATOR'S MANUAL 481039 FORWARD R F REVERSE 481568 IMPORTANT ADJUSTMENT PROCEDURES READ OPERATOR'S MANUAL FOR MORE DETAILS Check tire pressure- (Drive tires - 12 psi, Caster tires - 25 psi) NEUTRAL ADJUSTMENT Loosen jam nuts Rotate turnbuckle With an operator in the seat, engine running, control levers WARNING in neutral and the parking brake disengaged - adjust control DO NOT OPERATE WITHOUT
ページ12に含まれる内容の要旨
Section 3 SPECIFICATIONS SCAG “SABRE TOOTH TIGER” ZERO-TURN RIDER MODEL: STT– 31BSG ENGINE
! " "#$% & !' (%%)!" &* +
+ + #$,
- . &
+./.+
&+ (%% 01 %%
ページ13に含まれる内容の要旨
Section 3 SPECIFICATIONS (CON'T) SCAG “SABRE TOOTH TIGER” ZERO-TURN RIDER MODEL: STT– 31BSG CUTTER DECK 8"8-C,30B3
B2D8"8-( 30B3
B2-9+A=- + ==-.= -5B3
B- 7.&/ .5 %- .&C +//C
ページ14に含まれる内容の要旨
Section 4 OPERATING INSTRUCTIONS
CAUTION: ! Do not attempt to operate this mower unless you have read this manual. Learn the location and
" purpose of all controls and instruments before you
# operate this mower. $
% # $
ページ15に含まれる内容の要旨
Section 4 DUMP VALVE ! '
CONTROL
+
&
,- ,.# " # $%% ' !
/
& '! '
&
& '
#
' & %
ページ16に含まれる内容の要旨
Section 4 <
%
! 4.3 INITIAL RUN-IN PROCEDURES (First
%
( Day of Use or Approximately 10 Hours)
%
!
,; >1 , 9
%& -. &
% # :
#
$ %
ページ17に含まれる内容の要旨
Section 4
#
# #
#&%
# # #
&%
0 %
#
0 %
#
#&%
#
ページ18に含まれる内容の要旨
Section 4 .
4.9 AFTER OPERATION '
, +
( B !$@
4.7 HILLSIDE OPERATION
,
- WARNING:
ページ19に含まれる内容の要旨
Section 4 ; +
4.10 REMOVING CLOGGED MATERIAL !
%
ROTATING BLADES > " # NEVER PUT YOUR HANDS INTO THE DISCHARGE CHUTE FOR ANY REASON! Shut off the engine <
& and remove the key and only then use a stick or @
!$@
ページ20に含まれる内容の要旨
Section 4 LANYARD PIN 4.13 ADJUSTING CUTTING HEIGHT
% &?
,2
>
,8-2
#?
E , $
?
% 6 .2>7 - '
B
$
% HEIGHT ADJUSTMENT PEDAL 390S0140 #
