ページ1に含まれる内容の要旨
OPERATORS MANUAL OPERATORS MANUAL
OPERATORS MANUAL
OPERATORS MANUAL OPERATORS MANUAL
MODEL
RS-ZT
SC5062G
THIS MANUAL CONTAINS THE OPERATING
INSTRUCTIONS AND SAFETY INFORMATION
FOR YOUR SCAG ACCESSORY. READING
THIS MANUAL CAN PROVIDE YOU WITH AS-
SISTANCE IN MAINTENANCE AND ADJUST-
MENT PROCEDURES TO KEEP YOUR ACCES-
SORY PERFORMING TO MAXIMUM EFFI-
CIENCY. THE SPECIFIC MODELS THAT THIS
BOOK COVERS ARE CONTAINED ON THE IN-
SIDE COVER. BEFORE OPERATING YOUR
MACHINE, PLEASE READ ALL THE
ページ2に含まれる内容の要旨
WARNING FAILURE TO FOLLOW SAFE OPERATING PRACTICES MAY RESULT IN SERIOUS INJURY. * Keep all safety shields in place. * Before performing any maintenance or service, stop the machine and remove the spark plug wire. * If a mechanism becomes clogged, stop the engine before cleaning. * Keep hands, feet and clothing away from power-driven parts. * Read this manual completely as well as the Operator's Manual that came with your mower. * Keep others off the tractor (only one person at a
ページ3に含まれる内容の要旨
® TABLE OF CONTENTS SUBJECT PAGE Introduction..............................................................................................................1 Safety and Operating Instructions....................................................................... 1 Assembly Instructions........................................................................................... 2 - 4 Hardware List...........................................................................
ページ4に含まれる内容の要旨
INTRODUCTION 1. Read this technical manual and the technical manual that is supplied with the machine this This manual has been prepared to provide the attachment is used on. A replacement manual information you need to correctly assemble, is available by sending complete model and operate and maintain this attachment. Read it serial number to: carefully and keep it for future reference. Should Scag Power Equipment you ever need repair parts or service, contact your 1000 Metalcraft Dr. authorize
ページ5に含まれる内容の要旨
ASSEMBLY INSTRUCTIONS -Note- 5. Mount the sulky frame on the hitch ball and Before assembling and connecting this secure in place by pushing down the locking accessory to your machine, turn the engine lever on the coupler. off, remove the key, and remove the spark plug wire from the engine. -Note- When performing steps 5 through 8 keep in 1. Remove all crating and packing materials. mind that the (3) three tie rods will have Lay out
ページ6に含まれる内容の要旨
12 7/8" 13. Bolt one end of the other wheel tie rod below the lever on the right wheel spindle. Place a 1/2" ball joint spacer between the ball joint and wheel spindle lever. Secure using a 1/2-13 x 2" bolt and a 1/2-13 elastic stop WHEEL TIE ROD ADJUSTMENT nut. (See figure 2) SC502G Figure 1 14. Place the other end of the tie rod coming from the left wheel above the larger lever of the steering bellcrank located in the center of 10. On the (2) two wheel tie rods, adjust the ball the sulky frame
ページ7に含まれる内容の要旨
32 1/2" 21. Mount the seat onto the seat plate. Place the (4) four 3/8" flat washers between the seat and plate. Secure using (4) four 5/16-18 x 3/ STEERING TIE ROD ADJUSTMENT 4" bolts and (4) four 5/16" lock washers. Figure 3 SC504G 22. Mount the seat and seat plate to the seat spring using (2) two 3/8-16 x 1" bolts and 16. On the steering tie rod, adjust the ball joints (2) two 3/8" lock washers. on the tie rod so that you will get 32-1/2” distance between the center to center holes 23. Attach
ページ8に含まれる内容の要旨
Where Used List Part Number Qty. Description Where Used (4) Seat to Plate Hex HD Bolt, 5/16-18 x 3/4" 04001-08 4 (2) Seat Plate to Spring Hex HD Bolt, 3/8-16 x 1" 2 04001-19 (3) Hitch Brkt to Mower Hex HD Bolt, 3/8-16 x 1-1/4" 3 04001-32 (2) Coupler to Tongue Hex HD Bolt, 3/8-16 x 2-3/4" 2 04001-22 (2) Seat Spring to Tongue Hex HD Bolt, 7/16-14 x 4" 2 04001-89 (3) Tie Rod Ends Hex HD Bolt, 1/2-13 x 2" 04001-72 3 (1) Tie Rod End Hex HD Bolt, 1/2-13 x 3-1/4" 1 04001-90
ページ9に含まれる内容の要旨
RS-ZT SULKY 35 31 28 32 33 28A 35 29 30 5 34 30 6 16 36 12 15 44 11 12 27 40 9 40 25 6 24 8 11 48 7 43 3 21 9 49 23 2 8 1 5 18 39 22 47 7 20 46 49 2 46 3 47 6 4 56 19 45 26 57 8 17 51 14 42 50 55 50 41 5 50 6 53 12 54 8 13 9 37 38 10 52 39 11 SC505G 6
ページ10に含まれる内容の要旨
RS-ZT SULKY Ref. Part Ref. Part No. Number Description No. Number Description 1 46879 Sulky Frame 29 48014-02 Arm Rest Kit 2 48100-01 Bronze Bearing 30 48014-03 Arm Rest 3 04041-17 Flat Washer 31 04001-08 Hex Head Bolt, 5/16-18 x 3/4" 4 45377 Steering Bellcrank 32 48014-04 Mounting Bracket, RH 5 04001-72 Hex Head Bolt, 1/2-13 x 2" 33 48014-05 Mounting Bracket, LH 6 43041 Ball Joint Spacer 34 48014-07 Back Strap 7 48542 Ball Joint (RH Thread), 1/2-20 35 * Set Screw, 3/8-16 x 3/4" Flat Point 8 040
ページ11に含まれる内容の要旨
LIMITED LIMITED LIMITED W W WARRANTY- COMMERCIAL A ARRANTY- COMMERCIAL A ARRANTY- COMMERCIAL ACCESSOR CCESSOR CCESSORY Y Y LIMITED LIMITED W WARRANTY- COMMERCIAL A ARRANTY- COMMERCIAL ACCESSOR CCESSORY Y Any part of the Scag commercial accessory manufactured by Scag and found, in the reasonable judgment of Scag, to be defective in material or workmanship, will be repaired or replaced by an Authorized Scag Service Dealer without charge for parts and labor. The Scag accessory, including any defec
ページ12に含まれる内容の要旨
© 1998 PART NO. 03029 SCAG POWER EQUIPMENT PRINTED 6/98 DIVISION OF METALCRAFT OF MAYVILLE, INC PRINTED IN USA
